Installation Sheet

ManualsBrandsElkay ManualsKitchen SinksElkay Dayton 31-3/4" Double Basin Undermount Stainless Steel Kitchen Sink with Pullout Spray High-Arc Kitchen Faucet - Includes Bottom Grid and Drain

INSTALLATION

ATTENTION INSTALLER:

1. Make cutout using electronic DXF file.

2. Locate and drill the mounting holes (following

the countertop manufacturer’s instructions) as

shown below. Holes should allow even spacing

of mounting brackets around the sink. Type of

fasteners to be as recommended by countertop

supplier.

3. Fasten mounting brackets (optional accessory-

LKUCLIP8) to countertop loosely.

4. Using a good quality silicone caulk, apply a bead

evenly all around the top of the sink flanges.

5. Position and align sink over the countertop

opening. Press silicone onto countertop.

6. Tighten fasteners until mounting brackets are

snug against sink.

7. Check alignment of sink to countertop opening.

8. Tighten down fasteners evenly. Be careful not to

overtighten. Remove excess silicone.

DXUH 1/8” OVERHANG AND 1/2” REVEAL

COUNTERTOP INSTALLATION

COUNTERTOP

MOUNTING

BRACKET

(OPTIONAL

ACCESSORY)

SINK

SILICONE CAULK

(NOT FURNISHED)

COUNTERTOP

OVERHANG

APPROX. 1/8”

1/8” COUNTERTOP OVERHANG

1) ELKAY RECOMMENDS THAT UNDERMOUNT SINKS SHOULD BE INSTALLED BY A PROFESSIONAL

EXPERIENCED INSTALLER.

2) WARNING: THE ELECTRONIC TEMPLATE (DOWNLOAD DXF FILE FROM WWW.ELKAYUSA.COM) WILL

CREATE AN OVERHANG OF APPROXIMATELY 1/8" OR A REVEAL OF 1/2”. IT IS RECOMMENDED THAT

YOU DISCUSS THIS WITH YOUR CUSTOMER AND AGREE THAT THIS FINISHED APPEARANCE IS THE

DESIRED EFFECT. ELKAY IS NOT RESPONSIBLE FOR IMPROPER SINK OR COUNTERTOP

INSTALLATIONS. DUE TO THE AESTHETIC QUALITIES OF THE CONVERGING BOWL RADII, THE DXF

TEMPLATE PROVIDES THE ONLY OPENING RECOMMENDED FOR INSTALLATION OF ELKAY

UNDERMOUNT SINKS. SEE ILLUSTRATION BELOW.

3) ELKAY UNDERMOUNT SINKS SHOULD ONLY BE FASTENED TO A SOLID SURFACE COUNTERTOP

(I.E. GRANITE/CORIAN

/SILESTONE

4) ELKAY IS NOT RESPONSIBLE FOR SINK OR COUNTERTOP IF DAMAGED DURING INSTALLATIONS.

5) METAL EDGES MAY BE SHARP - USE CAUTION WHEN HANDLING.

6) FOLLOW ALL LOCAL PLUMBING AND BUILDING CODES.

7) INSPECT SINK FOR DAMAGE PRIOR TO BEGINNING INSTALLATION.

1/2” COUNTERTOP REVEAL

COUNTERTOP

MOUNTING

BRACKET

COUNTERTOP RECESSED

APPROX. 1/2"

SILICONE CAULK

(NOT FURNISHED)

SINK

1-1/8"

FASTENER

(NOT FURNISHED)

FASTENER

(NOT FURNISHED)

Summary of content (2 pages)

PAGE 1
DXUH 1/8” OVERHANG AND 1/2” REVEAL COUNTERTOP INSTALLATION ATTENTION INSTALLER: 1) 2) 3) 4) 5) 6) 7) ELKAY RECOMMENDS THAT UNDERMOUNT SINKS SHOULD BE INSTALLED BY A PROFESSIONAL EXPERIENCED INSTALLER. WARNING: THE ELECTRONIC TEMPLATE (DOWNLOAD DXF FILE FROM WWW.ELKAYUSA.COM) WILL CREATE AN OVERHANG OF APPROXIMATELY 1/8" OR A REVEAL OF 1/2”. IT IS RECOMMENDED THAT YOU DISCUSS THIS WITH YOUR CUSTOMER AND AGREE THAT THIS FINISHED APPEARANCE IS THE DESIRED EFFECT.
PAGE 2
Installation Instructions Suggestions for the Care and Cleaning of your Elkay Stainless Sink ELKAY SATIN FINISH Elkay's original highlighted satin finish is produced by an abrasive grinding operation which lends a uniform pattern of satin finish lines to the metal surface. All exposed areas then undergo a series of progressive machine and hand polishing operations. It is this careful polishing that makes an Elkay satin luster finish so beautiful…and so easy to clean and maintain.