Installation Sheet

Page 1 98526C (Rev. K - 06/19)
WaterSentry Plus Retro Bottle Filler and Water Cooler
7a. Turn on water supply and hold open the bubbler on cooler
 untilapproximately1gallonofwaterisdispensed.Thisushing
 procedurepurgesairandnecarbonparticlesfromthelter.
When 1 gallon of water has been purged through the cooler,
carefully inspect all water connections for leaks.
Theselterkitsaredesignedtobeusedwiththefollowing
Elkay products.
Filtered EZH2O
®
Bottle Filling Station Models
Examples include but not limited to: LZWS*, LZS*WS,
LVRC*WS, LMABF*WS
NOTICE: Do not use with water that is microbiologically
unsafe or of unknown quality without adequate
disinfection before or after the system. Filter
 mustbeusedwithltermonitorfor3000
gallon rating
General Installation Instructions
1. Theselterkitsmust be installed in compliance with all
state and local laws and regulations governing the
installation and use of this product. Maximum inlet
water temperature 100°F (38°C).
2. Mountlterheadinasuitablelocation,usingthelter
mounting bracket and screws supplied. Allow enough
 roomunderthelterheadforinstallationandremovalof
 ltercartridge(13"minimum).
3. Connectthecoldwatersupplytothelterthrougha
 shut-offvalveand3/8"O.D.tubing(suppliedbythe
installer). For ease of servicing, the shut-off valve
 shouldbelocatedwithineasyreachofthelter.
 NOTE:Theinletandoutletttingsuppliedas
 partofthelterheadareJohnGuestSuperseal
 ttingsthataccept3/8"O.D.tubingonthelter
 inletand1/4"O.D.tubingontheoutlet.Theymay
be used with copper, semirigid nylon or
polypropylene tubing, with a rated working
pressure equal or greater than encountered in
application. Do not use soft or braided tubing.
4. CAUTION: If supply pressure will ever exceed
100 psi, install a pressure regulator to limit the
 inletpressuretothelterto100psiorbelow.
 DONOTATTACHHOTWATERLINETOFILTER.
 Tomakeconnectionsonthelterhead,loosenlocknut.
Push the tube end past both o-rings to a positive stop in
 thelterheadrecess-approx.1",locknutmayhaveto
be backed out a little more. Screw the locknut hand tight
to seal (See Fig. 1). Ends of tubing must be cut square
and free of burrs and sharp ends that could cut or nick
the o-rings.
5. Connect the outletoftheltertotheinletoftheunion
 usingthe1/4"O.D.polytubingand1/4"unionsupplied.
6. Removelterfromcarton, remove protective cap, attach
 ltertolterheadbyrmlyinsertingintoheadand
 rotatinglterclockwise.
Filter Replacement
1. Turn inlet water valve off.
2. Open bubbler or activate the electric eye to relieve pressure
build-up in the system.
3Removeusedlterfromheadbyrotatingltercounterclockwise.
4.Removenewlter from carton, remove protective cap; cap may
 beplacedonoldltertoreducethechanceofwaterspillingfrom
 lterhousing.
5.Attachltertolterheadbyrmlyinsertingintoheadand
 rotatinglterclockwise.
NOTE:Thelterheadcontainsanautomaticshut-offvalvethat
stops the ow of water, if the lter is removed inadvertently
without shutting off the incoming water.
WaterSentry Plus In Wall Bottle Filler
7b. Turn on water supply and activate the electric eye on In-Wall
Bottle Filler until approximately 1 gallon of water is dispensed.
Please note that the electric eye activation times out at 30
seconds and will need to be activate repeatedly until one gallon
 hasbeenpassed.Thisushingprocedurepurgesairandne
 carbonparticlesfromthelter.When1gallonofwaterhas
 beenpurgedthroughthebottleller,carefullyinspectallwater
connections for leaks.
FILTER KIT
EWF3000WaterSentry
®
Plus Kit
(Lead, Chlorine, Taste & Odor, and Particulate Class I Reduction)
FOR COMMERCIAL USE ONLY
®
®
NOTE: This system and installation shall comply with applicable
state and local regulations.
(NOTE:CTOreplacementlterisonlycertiedtoNSF42claims;seeWSF6000RPerformance
Data Sheet for additional information.)
IMPORTANT NOTE - To avoid danger of an electric shock hazard, disconnect power to
yourunitbeforeinstallingorreplacingthelter.
B CA
SIMPLY PUSH IN
TUBE TO ATTACH
TUBE IS SECURED
IN POSITION
PUSH IN COLLET
TO RELEASE TUBE
OPERATION OF QUICK CONNECT FITTINGS
PUSHING TUBE IN BEFORE
PULLING IT OUT HELPS TO
RELEASE TUBE
OPERATIONOFQUICKCONNECTFITTINGS
SIMPLYPUSHIN
TUBETOATTACH
TUBEISSECURED
INPOSITION
PUSHINCOLLET
TORELEASETUBE
PUSHINGTUBEINBEFORE
PULLINGITOUTHELPSTO
RELEASETUBE
A B C
FIG. 2
FIG. 1
SeeNote4:Screwthelocknuthandtighttoseal
The WaterSentry
®
Plus lteristestedandcertiedbyNSFInternationaltoNSF/ANSI42and53
forthereductionofChlorine,TasteandOdor,ParticulateClassI,andLead.