Installation guide
MICROWAVE/
WALL
OVEN
COMBINATION
INSTALLATION
INSTRUCTIONS
if
oven
is
used
in
a
new
branch
circuit
installation
(1996
NEC),
mobile
home,
recreational
vehicle,
or
where
local
codes
DO
NOT
permit
grounding
through
the
neutral
(white)
wire,
the
appliance
frame
MUST
NOT
be
connected
to
the
neutral
wire
of
the
4-wire
electrical
system.
(see
figure
3):
1.
Disconnect
the
power
supply.
2.
Separate
the
green
(or
bare
copper)
and
white
appliance
cable
wires.
3.
In
the
junction
box:
Connect
appliance
and
power
supply
cable
wires
as
shown
in
Figure
3.
Cable
from
Power
Supply
Ground
Wire
co
Red
SSS
White
Wire
Ground
Wire
(Bare
or
Green
Wire)
Junction
Box
TS!
White
Wire
SN
_ULL--Listed
Conduit
er
Connector
(or
CSA
Cable
from
appliance
—_|isted)
Figure
3
4-WIRE
GROUNDED
JUNCTION
BOX
Model
and
Serial
Number
Location
The
serial
plate
is
located
along
the
interior
side
trim
of
the
oven
and
visible
when
the
door
is
opened.
When
ordering
parts
for
or
making
inquires
about
your
oven,
always
be
sure
to
include
the
model
and
serial
numbers
and
a
lot
number
or
letter
from
the
serial
plate
on
your
oven.
Serial
Plate
:
Location
4.
Cabinet
Installation
IMPORTANT
NOTE
Do
not
lift
the
oven
by
the
door
handle.
A
WARNING
Heavy
Weight
Hazard
®
Use
2
or
more
people
to
move
and
install
wall
oven.
«
Failure
to
follow
this
instruction
can
result
in
injury
or
damage
to
the
unit.
@
Unpack
the
wall
oven.
Remove
the
bottom
trim
taped
on the
oven
side
panel.
Remove
the
lower
oven door
to
reduce
the
weight
of
the
appliance
and
to
facilitate
its
handling
and
its
installation.
To
remove
the
oven door
see
following
steps:
1.
Open
the
door
to
the
fully
opened
position
(Figure
4).
2.
Pull
up
the
lock
located
on
each
hinge
toward
the
front
of
range.
You
may
have
to
apply
a
little
upward
pressure
on
the
lock
to
pull
it
up
(Figure
5).
3.
Grasp
the
door
by
the
sides,
pull
the
bottom
of
the
door
up
and
toward
you
to
disengage
the
hinge
supports.
Keep
pulling
the
bottom
of
the
door
toward
you
while
rotating
the
top
of
the
door
toward
the
appliance
to
completely
disengage
the
hinge
levers
(Figure
6).
4.
Proceed
in
reverse
to
replace
the
oven
door.
Make
sure
the
hinge
supports
are
fully
engaged
before
unlocking
the
hinge
levers.
NOTE:
The
oven
door
is
very
heavy.
Be
sure
to
have
a
firm
grip
before
lifting
the
oven
door
off
the
hinges. Use
caution
once
the
door
is
removed.
Do
not
lay
door
on
its
handle.
This
could
cause
dents
or
scratches.
Lock
engaged
for
door
removal
Figure
5
Lock
in
normal
position
Figure
4
Figure
6
‘\
Hinge
Slot
-
Door
removed
from
the
appliance