MSDS

ManualsBrandsEkena Millwork ManualsEkena Millwork Flooring4"W x 8"H x 3/4"P Standard Foster Plinth Block with Square Edge

Ekena Millwork Cellular PVC

MSDS

1.1. Product Identifier

Product name: Ekena Millwork PVC Trimboard and Sheet

Alternate name: Ekena Millwork Ecel-100/Ecel-1500 Trimboard and Sheet

1.2. Intended Use Of The Product

Use of the substance/mixture: Trim/Molding/Architectural components on the Exterior/Interior of buildings

1.3. Name, Address, And Telephone Of The Responsible Party

SECTION 2: Hazards identification

2.1. Classification of the substance or mixture

GHS-US classification

Not Classified. Within the meaning of the OSHA Hazard Communication Standard [29 CFR 1910.1200]: this mixture

is not considered a hazard when used in a manner which is consistent with the labeled directions. This mixture is

considered an article in its final form.

2.2. Label elements

Using the Toxicity Data listed in section 11 and 12 the product is labeled as follows. No applicable GHS categories.

[Prevention]: No GHS prevention statements

[Response]: No GHS response statements

[Storage]: No GHS storage statements

[Disposal]: No GHS disposal statements

2.3. Other Hazards

Other Hazards Not Contributing to the Classification: Cutting, sawing, grinding, or other operations that

generate dust may raise nuisance particles that can cause mechanical irritation to the skin, eyes, or respiratory

tract.

2.4. Unknown acute toxicity (GHS US)

No data available

MANUFACTURER

Ekena Millwork

2300 W. Main Street

Clarksville, TX 75426

866-607-0453

866-591-3143

2. Hazard(s) identification

1. Identification

Summary of content (7 pages)

PAGE 1
Ekena Millwork Cellular PVC MSDS 1. Identification 1.1. Product Identifier Product name: Ekena Millwork PVC Trimboard and Sheet Alternate name: Ekena Millwork Ecel-100/Ecel-1500 Trimboard and Sheet 1.2. Intended Use Of The Product Use of the substance/mixture: Trim/Molding/Architectural components on the Exterior/Interior of buildings 1.3. Name, Address, And Telephone Of The Responsible Party MANUFACTURER Ekena Millwork 2300 W. Main Street Clarksville, TX 75426 866-607-0453 866-591-3143 2.
PAGE 2
3.osition/information Composition/information on ingredients SECTION 3: Comp on ingredients 3. Composition/information on ingredients This product is an article as defined in 29 CFR 1910.1200. It will not result in exposure to hazardous chemicals under normal conditions of use. This product is not subject to the reporting requirements of Section 313 of Title III of the Superfund Amendments and Reauthorization Act of 1986 and 40 CFR Part 372.
PAGE 3
Symptoms/injuries after skin contact: Not expected to be a primary route of exposure. Risk of thermal burns on contact with molten product. Symptoms/injuries after eye contact: Not expected to be a primary route of exposure. Excessive dust production at the time of cutting may cause minor eye irritation. Symptoms/injuries after ingestion: Ingestion is not considered a potential route of exposure. 4.3.
PAGE 4
may raise nuisance particles that can cause mechanical irritation to the skin, eyes, or respiratory tract. Polyvinyl chloride dust accumulation can present a dust explosion hazard. Take necessary measures to limit dust production, and follow applicable regulations. Wear gloves when cutting or fabricating sheet Hygiene measures: Handle in accordance with good industrial hygiene and safety procedures.
PAGE 5
SECTION 9: Physical and chemical properties 9.1. Information on basic physical and chemical properties Physical state : Solid Appearance : Finished Sheet/Board. White.
PAGE 6
10. Stability and reactivity Reactivity: Hazardous reactions will not occur under normal conditions. Chemical Stability: Stable at standard temperature and pressure. Sustained temperatures above 150°F may cause slow degradation. Possibility Of Hazardous Reactions: Hazardous polymerization will not occur. Conditions To Avoid: Direct sunlight. Extremely high or low temperatures. Incompatible materials. Incompatible Materials: Strong acids. Strong bases. Strong oxidizers.
PAGE 7
13. Disposal considerations Other information: Avoid release to the environment. SECTION 13: Disposal considerations 13.1. Waste treatment methods Sewage disposal recommendations: Do not empty into drains; dispose of this material and its container in a safe way. Waste disposal recommendations: Dispose of waste material in accordance with all local, regional, national, and international regulations. 14. Transport information SECTION 14: Transport information In accordance with ICAO/IATA/DOT/TDG 14.1.