Manual

Instructions : Heavy Duty Record Storage Rack,

Welded Bulk Storage Tire Rack

See reverse side for product parts list & contact information

General Instructions

Safety Instructions

Edsal Record Storage Rack is engineered to offer maximum flexibility as well as ease and quickness of assembly. The

rack units can stand individually, or for greater stability, be joined together using the common post. Individual beams

can be adjusted without disturbing the beams in adjoining units. These instructions should be followed exactly. All

parts supplied must be used as shown. Any alteration or deviation from this instruction sheet can result in unit failure.

After the unit is assembled, it must be placed on a level surface for safety, and optimal product performance.

This storage rack unit must be placed on a level surface. Failure to do so can result in unit failure, poor product per-

formance, or a possible “tipping” safety hazard. DO NOT STAND ON THE UNIT OR USE THE UNIT AS A LADDER !

DO NOT OVERLOAD ! Evenly distribute the weight on each shelf, and keep the heaviest loads on the bottom shelf.

Use care and the proper attire when working with metal parts.

Assembly Instructions

Figure 4

Starter Add-On

Figure 2

Attach the beams to the welded end frames as seen in figure 1.

Use both welded end frames to establish the left and the right sides

of the units. After a beam has been placed to the end units, tap

down with a hammer to help drive the beam end clip tabs into the

end frame post slots. To secure the beam to the end frame, insert

the plastic canoe clips through the hole in the beam bracket and

into the frame (see figure 1). NOTE: If the beam end clip tabs

become bent due to mishandling. It may be necessary to ad-

just the tabs back to their proper form.

For record storage rack, attach tie bars to the beams by inserting

them into the slots of the beams (see figure 1). NOTE : TIRE RACK

DOES NOT REQUIRE TIE BARS AND ARE NOT INCLUDED.

Particle Board Shelving can now be added to each level to com-

plete the record storage rack unit (see figure 2).

Tires can now be added to each level to complete the tire rack unit

(see figure 3).

Each end frame can be used as a common end, add on units can

be purchased to expand storage capacity (see figure 4).

Figure 1

End Frame Post

End Frame Post Slots

Canoe Clip

Beam

Tie Bar

Beam End

Clip Tabs

Figure 3

PAGE 1
Instructions : Heavy Duty Record Storage Rack, Welded Bulk Storage Tire Rack Safety Instructions This storage rack unit must be placed on a level surface. Failure to do so can result in unit failure, poor product performance, or a possible “tipping” safety hazard. DO NOT STAND ON THE UNIT OR USE THE UNIT AS A LADDER ! DO NOT OVERLOAD ! Evenly distribute the weight on each shelf, and keep the heaviest loads on the bottom shelf. Use care and the proper attire when working with metal parts.
PAGE 2
Heavy Duty Record Storage Rack Parts List Model Number 1KAC4 1KAC5 1KAC6 1KAC7 1KAC8 1KAC9 1KAD1 1KAD2 1KAD4 1KAD6 1KAD8 1KAE1 RSS6018 RSS6036 RSS7218 RSS7236 RSS6918 RSS9636 RSA6018 RSA6036 RSA7218 RSA7236 RSA9618 RSA9636 Unit Starter Starter Starter Starter Starter Starter Add-on Add-on Add-on Add-on Add-on Add-on Upright Frame BWRS1872LG BWRS3672LG BWRS1872LG BWRS3672LG BWRS1872LG BWRS3672LG BWRS1872LG BWRS3672LG BWRS1872LG BWRS3672LG BWRS1872LG BWRS3672LG Beam (2) (2) (2) (2) (2) (2) (1) (1) (1) (