Edelbrock E-Force Supercharger 2014 GM Truck and SUV 1500 5.3L and 6.
Edelbrock E-Force Supercharger System 2014 GM Truck & SUV 1500 5.3L and 6.2L Installation Instructions INTRODUCTION Thank you for purchasing the Edelbrock Supercharger System for the 2014 GM 1500 Trucks and SUVs. This system utilizes the same Eaton Gen VI TVS Supercharger rotors as the previous E-Force supercharger but housed inside a redesigned supercharger manifold. Paired with bolt-on runners, this new package will fit under the factory hood with no modifications to the stock body or hood.
Edelbrock E-Force Supercharger System 2014 GM Truck & SUV 1500 5.3L and 6.2L Installation Instructions IMPORTANT WARNINGS Before beginning the installation, use the enclosed checklist to verify that all components are present in the box then inspect each component for damage that may have occurred in transit. If any parts are missing or damaged, contact Edelbrock Technical Support (800-416-8628), not your parts distributor.
Edelbrock E-Force Supercharger System 2014 GM Truck & SUV 1500 5.3L and 6.2L Installation Instructions IMPORTANT WARNINGS CONT’D Please employ proper towing etiquette when towing steep grades. Turn off Air Conditioner and avoid aggressive towing behaviors to avoid any overheating that may occur. DO NOT exceed the manufacturer’s maximum tow rating for the vehicle. 91 octane or higher gasoline is required at all times.
Edelbrock E-Force Supercharger System 2014 GM Truck & SUV 1500 5.3L and 6.2L Installation Instructions INSTALLATION HARDWARE IDENTIFICATION GUIDE (Parts Are Not To Scale) Bag #1 (3x) - M8 x 1.25 x 130mm SHCS (1x) - M10 x 1.5 x 40mm Hex Flange (1x) - M8 x 1.25 x 25mm Hex Flange (2x) - M10 Washer (1x) - M10 x 1.5 x 200mm Stud (1x) - M10 x 1.5 Nylon Insert Nut (1x) - M8 Washer Bag #2 (8x) - 3/4” Hose Clamp (2x) - M8 x 1.0 x 16mm BHCS Flange (8x) - M6 x 1.
Edelbrock E-Force Supercharger System 2014 GM Truck & SUV 1500 5.3L and 6.2L Installation Instructions BRACKET AND FEAD IDENTIFICATION GUIDE (Parts Are Not To Scale) Upper / Driver LTR Bracket Upper / Passenger LTR Bracket FEAD Bracket Lower / Driver LTR Bracket Water Pump Bracket Grooved Idler Pulley Lower / Passenger LTR Bracket Smooth Idler Pulley (2) Small Spacer Recovery Tank Bracket Large Spacer ©2015 Edelbrock LLC Part #1568, 1569 Page 5 Water Pump Isolator Brochure #63-1568 Rev.
Edelbrock E-Force Supercharger System 2014 GM Truck & SUV 1500 5.3L and 6.2L Installation Instructions HOSE IDENTIFICATION GUIDE (Parts Are Not To Scale) Manifold To Recovery Tank Recover Tank to Water Pump Manifold to LTR Hose Water Pump to LTR Hose PCV - Valley to Nose 1/4” Hose (34”) Qty (2) PCV Hose ©2015 Edelbrock LLC Part #1568, 1569 Page 6 Brochure #63-1568 Rev.
Edelbrock E-Force Supercharger System 2014 GM Truck & SUV 1500 5.3L and 6.2L Installation Instructions WIRE HARNESS GUIDE (Parts Are Not To Scale) Intercooler Water Pump Fuse EVAP Solenoid Constant +12v Power Wire EVAP Engine Harness WATER PUMP HARNESS Relay Ground Strap ETC Extension harness included but not pictured. TMAP HARNESS MAF Sensor Engine Harness TMAP Sensor MAF Sensor MAP Sensor Engine Harness ©2015 Edelbrock LLC Part #1568, 1569 Page 7 Brochure #63-1568 Rev.
Edelbrock E-Force Supercharger System 2014 GM Truck & SUV 1500 5.3L and 6.2L Installation Instructions HOSE ROUTING DIAGRAM Supercharger Intercooler Reservoir Tank Heat Exchanger (LTR) Water Pump ©2015 Edelbrock LLC Part #1568, 1569 Page 8 Brochure #63-1568 Rev.
Edelbrock E-Force Supercharger System 2014 GM Truck & SUV 1500 5.3L and 6.2L Installation Instructions TEMPLATE (DO NOT SCALE TEMPLATE WHEN PRINTING) Splash Guard Template ©2015 Edelbrock LLC Part #1568, 1569 Page 9 Brochure #63-1568 Rev.
Edelbrock E-Force Supercharger System 2014 GM Truck & SUV 1500 5.3L and 6.2L Installation Instructions E-MAIL EDELBROCK YOUR STOCK VEHICLE CALIBRATION AND VEHICLE INFORMATION PLEASE COMPLETE THIS PROCEDURE PRIOR to starting the installation of your E-Force supercharger system. This will allow our calibration team to complete your calibration file while the installation of your supercharger system is being completed.
Edelbrock E-Force Supercharger System 2014 GM Truck & SUV 1500 5.3L and 6.2L Installation Instructions SUPERCHARGER INSTALLATION 10. DO NOT unplug the programmer until prompted. WARNING: Battery must be sufficiently charged before starting the PCM flashing procedure. Only begin the PCM flashing procedure when you have downloaded the updated calibration file to the handheld programmer. Do not flash the PCM until you are ready to install the supercharger.
Edelbrock E-Force Supercharger System 2014 GM Truck & SUV 1500 5.3L and 6.2L Installation Instructions 16. Using a flathead screwdriver, loosen the worm clamps on the air inlet tube and remove the assembly from the throttle body and airbox. 19. Detach the PCV hose located on the valley plate. On 5.3L applications the hose connects to the driver side of the intake manifold. On 6.2L applications, it connects to the front of the intake manifold. 5.3L 6.2L 17.
Edelbrock E-Force Supercharger System 2014 GM Truck & SUV 1500 5.3L and 6.2L Installation Instructions 22. Using a panel puller, disengage four (4) Christmas tree push pins securing the engine harness to the rear of the manifold cover. With Christmas trees removed, carefully remove the intake manifold. 23. Clean the intake port surfaces with a shop rag. Cover the ports with protective tape to keep out debris. 27. Using a 15mm socket, remove the factory tensioner. 28.
Edelbrock E-Force Supercharger System 2014 GM Truck & SUV 1500 5.3L and 6.2L Installation Instructions 31. Apply Blue thread locker to one end of the M10 Stud from Bag #1. Thread the stud, by hand, into the alternator bracket. Using the supplied M10 nut from Bag #1, continue threading the stud into the bracket until it stops. Remove the M10 nut. 35. Using one (1) M8 washers and one (1) M8 x 25mm bolts from Bag #1, install the other smooth idler pulley to the FEAD bracket with a 12mm socket.
Edelbrock E-Force Supercharger System 2014 GM Truck & SUV 1500 5.3L and 6.2L Installation Instructions 39. Connect the supplied TMAP harness to the TMAP sensor located on the passenger side runner. 40. Remove the protective tape from the passenger side cylinder head. Place the passenger side runner onto the cylinder head using the dowel pins for alignment. Apply Blue thread locker to the threads of five (5) M6 x 85mm Hex bolts from Bag #3.
Edelbrock E-Force Supercharger System 2014 GM Truck & SUV 1500 5.3L and 6.2L Installation Instructions 48. Using a 10mm socket, remove the factory EVAP 51. With the help from an assistant, carefully lower the solenoid on the intake manifold and install it to the supercharger manifold onto the runners. Make sure to align supercharger manifold using the factory bolt. the manifold to runner gaskets properly before proceeding.
Edelbrock E-Force Supercharger System 2014 GM Truck & SUV 1500 5.3L and 6.2L Installation Instructions 54. Using a breaker bar, rotate the tensioner counterclockwise and install the drive belt using the routing diagram below. S/C 56. Using a 10mm socket, remove a bolt and nut securing the engine harness support right of the new EVAP location. Carefully lift up the harness support and temporarily relocate it to access the EVAP solenoid. ALT. IDLER IDLER IDLER TEN. WATER PUMP CRANK 57.
Edelbrock E-Force Supercharger System 2014 GM Truck & SUV 1500 5.3L and 6.2L Installation Instructions 59. Using a 10mm socket, remove the throttle body from 62. Using a 10mm socket, remove four (4) bolts securing the stock manifold and install it onto the supercharger the top of the grill assembly. Some vehicles with have a manifold using the factory bolts and the supplied throttle total of five (5) bolts. body O-ring gasket. NOTE: Throttle body flange is tapped for both 5.3L and 6.2L throttle bodies.
Edelbrock E-Force Supercharger System 2014 GM Truck & SUV 1500 5.3L and 6.2L Installation Instructions 65. Using a 7mm socket, remove four (4) bolts (two per side) securing the grill assembly. Proceed to Step 71. TIP: Fender lining doesn’t have to be removed, but will simplify this procedure. 68. Using a panel puller, remove two (2) push pins (GREEN ARROW) securing the wheel well liner to the bottom of the facia.
Edelbrock E-Force Supercharger System 2014 GM Truck & SUV 1500 5.3L and 6.2L Installation Instructions 71. Using a 10mm socket, remove four (4) bolts securing 74. Using a 13mm socket, remove three (3) bolts securing the driver side headlamp. the front support brace to the chassis. 72. Carefully rotate the headlamp forward and disconnect the headlamp power connector. Repeat headlamp removal procedure for the passenger side headlamp. 75.
Edelbrock E-Force Supercharger System 2014 GM Truck & SUV 1500 5.3L and 6.2L Installation Instructions NOTE: There are two variants of the front support brace. Variant I has a flat support plate while Variant II has a support plate with raised sides. If you have variant II, proceed to Step 77. Otherwise disregard and proceed to Step 78. VARIANT I 78. Apply 3-4” of foam tape to the support bars to prevent LTR and brace contact.
Edelbrock E-Force Supercharger System 2014 GM Truck & SUV 1500 5.3L and 6.2L Installation Instructions 81. Using a 10mm socket, remove two (2) lower bolts on 85. Install the LTR to Manifold hose to the top LTR barb and the support brace. Using the same bolts, loosely secure the secure with a hose clamp from Bag #2. TIP: Use the hose lower LTR brackets to the support brace. Using two (2) M8 routing diagram to reference how to clock these hoses.
Edelbrock E-Force Supercharger System 2014 GM Truck & SUV 1500 5.3L and 6.2L Installation Instructions 88. Re-secure the support brace to the chassis using the factory hardware. 93. Using a 10mm socket and four (4) M6 x 10mm Hex Flange bolts from Bag #2, secure the recovery tank bracket to the recovery tank. Install the Recovery Tank to Water Pump hose to the bottom barb on the recovery tank and secure with a hose clamp from Bag #2. 89.
Edelbrock E-Force Supercharger System 2014 GM Truck & SUV 1500 5.3L and 6.2L Installation Instructions 96. Remove the ECU splash guard using a 10mm socket 99. Using a 15mm socket, remove two bolts securing the and a panel puller. TIP: Splash guard located next to the bumper support brace. TIP: These two bolt locations plus the bolt securing the ECU splash shield (GREEN) are the front driver chassis mount. mounting locations for the water pump bracket. 100.
Edelbrock E-Force Supercharger System 2014 GM Truck & SUV 1500 5.3L and 6.2L Installation Instructions 102. Using wire ties, or equivalent, secure the relay on the 105. Route the water pump connector down towards to water pump harness to the vehicle harness mounted on the water pump and the EVAP connector over towards the driver side firewall. Route the EVAP and water pump EVAP. connectors towards the front of the vehicle following the hood latch cable.
Edelbrock E-Force Supercharger System 2014 GM Truck & SUV 1500 5.3L and 6.2L Installation Instructions 110. Install the supplied grommets and Quick Disconnect 113. Install the 45° end of the supplied PCV hose to the fittings from Bag #4 onto the supplied air inlet tube. driver side valve cover. Install the 90° end to the fitting on the air inlet tube. 111. Install the hump coupler onto the airbox.
