Warranty

PRODUCT DATA SHEET: ECOBOND
®
LBP
For additional information, contact ECOBOND LBP, LLC: Ph: 888-520-7132 Email: [e-mail] www.ecobondlbp.com
Corporate Office: 14045 West 66
th
Avenue; Arvada, CO 80004
ECOBOND
®
LBP, Lead Based Paint Sealant and Treatment (Latex Primer). Used by residential and commercial contractors, painters, and home owners as a multi-use lead based paint
product that Seals and Treats Lead Hazards during Renovation, Repair, Painting (RRP), lead paint maintenance, commercial/industrial remediation and demolition activities
BENEFITS (when used as specified)
 Lead-Based Paint Management – seals and treats lead dust
and lead in paint (use as directed); used in interim control as
allowed by EPA/HUD; simplifies clean-up
 Eco-Protective – supports worker and resident safety;
reduces airborne lead up to 99%; reduces lead hazards up
to 95% (EPA Method 1311) for disposal; reduces lead bio-
accessibility by up to 75% (EPA 9200.1-86)
 Easy and Safe to Use –Paint it on, Leave it on latex formula;
no hazardous solvents or fumes; low VOCs
 Low Cost – less than 25¢/sf
 Mold and Mildew Resistant – ASTM D5590-00 (modified)
 Fire Resistant – ASTM E84, Flame spread “0”, Smoke
developed “0” NFPA/IBC Class A Coating
 Liability Protection – reduces worker and occupant lead
exposure; simplifies clean up; supports obtaining final
inspection clearance
USES
 Residential: Renovation, Repair, Painting (RRP); Lead Paint
Maintenance and Lead Paint Stabilization
 Commercial: Lead Remediation, Lead Paint Stabilization,
Demolition and Firing Ranges
 Prior to lead paint removal methods
 As a lead dust sealant and treatment
 For treatment of lead paint
 Allowed for use in all 50 states as Lead Paint Interim Control
(42 USC 63A 4851b(13)), Check local requirements
 High quality interior/exterior latex paint formula: tintable
interior top coat or primer; exterior primer, product accepts
most topcoats
 Note: This product is not a permanent epoxy encapsulant as
defined by HUD/EPA and is not to be used as a substitute
for a permanent encapsulant with 20 year warranty
PRODUCT APPLICATION
 NOTE: Due to settling, prior to use, mechanically re-mix
thoroughly for 1 minute per gallon. (Following mixing, if
needed add up to 1 cup of water per gallon)
 Use on a wide variety of surfaces including (but not limited
to) wood, drywall, steel, masonry/brick, concrete and asphalt
 Interior application – use as a primer or as tintable topcoat;
Exterior application – use as primer
 Minimal surface preparation required. Surface must be dry;
remove excess grime, dirt, oil and grease. Extra surface
preparation may be required for application on high gloss oil
or epoxy surfaces.
 Initial testing is recommended by painting a 1 ft x 1 ft section
prior to full application to ensure satisfactory results.
 Do not apply at temperatures below 50
º
F or within 8 hours
of any anticipated precipitation.
 Dry to touch is 4 hours. Average cure time to apply topcoat
is 24 hours. Any application during periods of high humidity
or low temperatures will increase the amount of drying time.
 Apply at typical 6-8 mil wet thickness depending on lead-
based paint condition and lead contamination.
 Product is tintable and pre-textured
EQUIPMENT
 Apply with airless sprayer, brush, or roller
 For airless sprayer, minimum recommended spray tip
orifice: .027 - .031 with all filters removed. Recommended
mesh size: 20 or lower. Pump size 0.70 GPM or larger (e.g.
Titan 640 or Graco 695)
CLEAN-UP
 Easy cleanup with warm, soapy water
STORAGE
Product must be stored indoors or under cover at temperatures
of 50
º
F – 100
º
F
PRODUCT SPECIFICATIONS
 One gallon covers up to 300 sf, dependent on surface
conditions
 1 gallon weighs approximately 11 lbs.
 No petroleum distillates or hazardous material
 Non-combustible latex based product
SAFETY PRECAUTIONS
 Provide adequate ventilation - if you experience difficulty in
breathing, leave the area to obtain fresh air. If continued
difficulty is experienced, get medical assistance
immediately.
 Avoid contact with eyes and skin - in case of eye contact,
flush immediately with plenty of water for at least 15 minutes
and get medical attention; for skin, wash thoroughly with
soap and water. If swallowed, get medical attention
immediately.
 Spray equipment must be in good condition and used in
accordance with manufacturer’s instructions.
 The use of a respirator, eye protection, and protective
clothing is recommended.
 Wash hands, tools, and equipment with warm soapy water
after use in an area that is safe for lead disposal; properly
dispose of resulting waste and wastewater as it may contain
lead.
 Visit the USEPA website (http://www.epa.gov/lead/) for
guidance and requirements for working with lead paint