Table of Contents Ceiling Bracket Tools Needed Preparation 30 inches Hanging the Fan 8 PA G E 9 ? ? ? 14 PA G E 13 Troubleshooting PA G E 1 PA G E 11 5 Blades Maintenance, Operation & Cleaning Light Kit PA G E 10 PA G E 7 Switch Housing 4 Motor Housing Wiring PA G E 6 3 PA G E Ladder PA G E 2 PA G E 7 feet PA G E We are proud of our work and appreciate the opportunity to supply you with the best ceiling fan available anywhere in the world.
What to Expect with Your Installation Read and Save These Instructions If you are unfamiliar with wiring, use a qualified electrician. This product conforms to UL Standard 507. WARNINGS 30 inches from blade tip to nearest wall or obstruction Must be able to secure the fan to building structure or fan-rated outlet box 7 feet from bottom edge of blade to the floor Know your wiring Assess location w.
Tools Needed Ladder Power Drill (optional) Screwdrivers 9/64” Drill Bit (optional) If mounting to a support structure, you will also need these tools.
Ceiling Bracket Bumper er w o nP r Tu OFF Make sure all four (4) bumpers are still attached. To avoid possible electrical shock, before installing your fan, disconnect the power by turning off the circuit breakers to the outlet box associated with the wall switch location. Use wood screws Use machine screws (included) when securing (provided with outlet to support structure with box) when securing to approved electrical outlet existing ceiling fan-rated box. Drill 9/64” pilot holes outlet box.
Ceiling Bracket (continued) Preparation Time Saver Tip: Get a helper to insert grommets, found in the hardware bag, into the blades while you’re doing the next couple of steps.
Hanging the Fan Ground Wire Screw Hole While holding the wires out of the way, lift the motor assembly and place the square hanger into the opening in the ceiling bracket. Be sure the ground wire attached to the hanger faces out of the large opening in the ceiling bracket. Locking Screw Once the motor is in the ceiling bracket, use the two locking screws found in the hardware bag to secure the motor to the ceiling bracket. Note: Fan style may vary.
Wiring OM FR CEILIN Note: To connect the wires, hold the bare metal leads together and place a wire connector over them, then twist clockwise until tight. G OM FR T KE Black FR (Ungrounded) M FA N Blue FRO (Ungrounded) AC Blue ING BR Black CEIL White M Using the orange wire connectors from the hardware bag, connect the black wire (ungrounded) from the ceiling to the black and the blue wires from the fan. Connect the white wire (grounded) from the ceiling to the white wire from the fan.
Motor Housing Notch Motor Housing Screw Indentation Screw Holes Raise the motor housing up over the motor and ceiling bracket. Turn the motor housing so the screw holes align and the indentation in the housing locks into place with the notch in the ceiling bracket. The motor housing is not secured until the next step is complete. Do not leave unattended. With a Phillips head screwdriver, install the four motor housing screws found in the hardware bag. Tighten all four screws securely.
Blades Insert grommets found in the hardware bag into the holes in the blades, then secure each blade to a blade iron with screws found in the hardware bag. Lightly attach the blade irons to the motor with screws found in the hardware bag, then securely tighten after both screws are attached.
Switch Housing Screw two (2) housing assembly screws from the hardware bag halfway into the motor housing. It does not matter which two screw holes you choose. Feed the wire plug through the center hole of the upper switch housing, then wrap keyhole slots around the screws and twist counterclockwise. the Insert the third screw, found in hardware bag, into place and then tighten all three (3) screws. Make sure the upper switch housing is securely attached to the mounting plate.
Light Kit Switch Housing Screw Partially install two of the switch housing screws found in the bag. Connect the plugs from the upper and lower switch housings. Make sure to line up the colored markings on the connectors. Notch Switch Housing Screw Align the notches in the sides of the lower switch housing with the upper switch housing screws. Lift the lower switch housing. Twist the lower switch housing clockwise to lock into place. Then thread the fan pull chain through the hole in the light kit.
Light Kit (continued) Metal Plate Light Pull Chain Fan Pull Chain Globe Globe Keeper Finial Cap CONGRA YOU’RETULATIONS! DONE! Finial Install a bulb into each of the sockets. When necessary, replace with bulbs of the same wattage Press the globe and globe keeper flush against the metal plate. Thread the light pull chain through the hole in the center of the finial cap and thread the fan pull chain through the hole in the side of the cap.
Maintenance, Operation & Cleaning Metal Plate r we o nP r Tu ON Globe Globe Keeper Reverse Switch Finial Cap Finial Changing the bulbs - Unscrew the finial and remove it from the threaded rod. Remove the finial cap and unscrew the globe keeper while supporting the globe with your other hand. Carefully remove the globe. Unscrew bulbs and replace with bulbs of same type and wattage. Reinstall the globe assembly. Changing the direction of air flow - Move the reverse switch to the opposite position.
Troubleshooting Fan doesn’t work Excessive wobbling • Make sure power switch is on. • Tighten all of the blade and blade iron screws until they are snug. • Pull the pull chain to make sure it is on. • Push the motor reversing switch firmly left or right to ensure that it is engaged. 2-Year Energy Warranty • Use the provided balancing kit and instructions to balance the fan. • Check the circuit breaker to ensure the power is turned on. • Make sure the blades spin freely.
