Cut Sheet

ManualsBrandsEaton B-Line ManualsBeamBeam Clamp Retaining Strap, Rod Size: 3/8", Length: 10"

Beam Clamps

All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.

Beam Clamps

Pipe Hangers & Supports

Size Range:

/8"-16 thru

/4"-10 rod

Material: Steel

Function: Designed for attaching a hanger rod to the flange of a beam.

Approvals: Conforms to Federal Specification WW-H-171E &

A-A-1192A, Type 19 and Manufacturers Standardization Society

ANSI/MSS SP-69 & SP-58, Type 19.

Finish: Electro-Galvanized or Hot-Dip Galvanized

Ordering: Part number and finish. When retaining strap is required,

order B312 separately. See page 39.

Recommended Set Screw Torque:

/2”-13 = 350 in-lbs (39.5 N•m)

/8”-11 = 700 in-lbs (79.0 N•m)

Minimum Flange Thickness:

For B321-1 thru B321-3 =

/8” (9.5)

For B321-4 & B321-5 =

/8” (15.9)

Size Range:

/4"-20 thru

/8"-11 rod

Material: Steel

Function: Designed for attaching a hanger rod to the flange of a beam.

Approvals: Conforms to Federal Specification WW-H-171E & A-A-1192A,

Type 19 and Manufacturers Standardization Society ANSI/MSS SP-69 &

SP-58, Type 19.

Finish: Electro-Galvanized or Hot-Dip Galvanized

Order By: Part number and finish. When retaining strap is required, order

B312 separately. See page 39.

Recommended Set Screw Torque:

/8”-16 = 150 in-lbs (16.9 N•m)

/2”-13 = 350 in-lbs (39.5 N•m)

Part Rod Size Setscrew CTDesign Load Approx. Wt./100

No. A Size

in. (mm) in. (mm) Lbs. (kN) Lbs. (kg)

B303

/4”-20

/8”-16 2

/16" (58.7) 11 Ga. (3.0) 400 (1.78) 72 (32.6)

B304

/16”-18

/8”-16 2

/16" (58.7) 11 Ga. (3.0) 600 (2.67) 72 (32.6)

B305

/8”-16

/8”-16 2

/16" (58.7) 11 Ga. (3.0) 600 (2.67) 72 (32.6)

B306

/8”-16

/2”-13 2

/16" (61.9) 7 Ga. (4.5) 1100 (4.89) 97 (44.0)

B307

/2”-13

/2”-13 2

/16" (61.9) 7 Ga. (4.5) 1100 (4.89) 97 (44.0)

B308

/2”-13

/2”-13 2

/16" (65.1)

/4" (6.3) 1500 (6.67) 133 (60.3)

B309

/8”-11

/2”-13 2

/16" (65.1)

/4" (6.3) 1500 (6.67) 133 (60.3)

B303-B309 - Beam Clamps

Fig. B321 - Series Beam Clamps

Part Rod Size Setscrew CTDesign Load Approx. Wt./100

No. A Size

in. (mm) in. (mm) Lbs. (kN) Lbs. (kg)

B321-1

/8”-16

/2”-13 3

/16" (92.1)

/4" (6.3) 1300 (5.78) 187 (84.8)

B321-2

/2”-13

/2”-13 3

/16" (92.1)

/4" (6.3) 1400 (6.23) 186 (84.3)

B321-3

/8”-11

/2”-13 3

/16" (92.1)

/4" (6.3) 1600 (7.12) 185 (83.9)

B321-4

/8”-11

/8”-11 3

/32" (94.4)

/16" (7.9) 1800 (8.00) 239 (108.4)

B321-5

/4”-10

/8”-11 3

/32" (94.4)

/16" (7.9) 2000 (8.89) 238 (107.9)

Set Screw

Included

/16" (42.8)

Maximum

Flange

Thickness

/8"

(41.3)

/4"

(82.5)

/8" (22.2)

Maximum

Flange

Thickness

/8"

(28.6)

/2"

(63.5)

Set Screw

Included

Summary of content (8 pages)

PAGE 1
Beam Clamps Set Screw Included B303-B309 - Beam Clamps Size Range: 1/4"-20 thru 5/8"-11 rod T Material: Steel 11/8" 7/8" (22.2) Maximum Flange Thickness Function: Designed for attaching a hanger rod to the flange of a beam. Approvals: Conforms to Federal Specification WW-H-171E & A-A-1192A, Type 19 and Manufacturers Standardization Society ANSI/MSS SP-69 & SP-58, Type 19. (28.6) C Finish: Electro-Galvanized or Hot-Dip Galvanized A Order By: Part number and finish.
PAGE 2
Beam Clamps Fig. 69 - Beam Clamp Retaining Strap (B-Line B3367) Component of State of California OSHPD Approved Seismic Restraints System Size Range: 3/8"-16 thru 3/4"-10 rod 4” (101,6mm) thru 16” (406.4mm) lengths Note: longer lengths are available consult factory Material: Pre-Galvanized Steel Function: To offer more secure fastening of various types of beam clamps to beam where danger of movement might be expected.
PAGE 3
Beam Clamps Fig. 69R - Retrofit Capable Beam Clamp Retaining Strap Component of State of California OSHPD Approved Seismic Restraints System Size Range: 3/8"-16 & 1/2"-13 rod 4” (101,6mm) thru 16” (406.4mm) lengths Note: longer lengths are available consult factory Material: Pre-Galvanized Steel Function: To offer more secure fastening of various types of beam clamps to beam where danger of movement might be expected.
PAGE 4
Beam Clamps B312 - Retaining Strap Material Thickness 14 Gauge (1.9) Size Range: 9” (228.6mm) to 18” (457.2mm) strap lengths L Material: Steel 13/4" (44.4) Function: Designed for use with B303-B309 and B321 beam clamps. Finish: Pre-Galvanized 1/2" 11/4" (31.7) Order By: Part number and finish. (12.7) 1/4" (6.3) Notes: Maximum beam thickness 3/4” (19.0). For thicker beams step up one flange width size. Requires field forming on beam. Beam Clamps Part No. For Flange With L Approx. Wt.
PAGE 5
Beam Clamps B3050 - Beam Clamp (TOLCO Fig. 62) A Center of bolt to bottom of beam flange. Material: Steel Function: Recommended for the suspending of hanger rod from the center of an I-beam, equally distributing the load on both sides of the beam. Use with B3210 eye rod, B3211 welded eye rod or B3200 weldless rye nut.
PAGE 6
Beam Clamps B3055 - Steel Beam Clamp Size Range: 3/8"-16 thru 1"-8 rod Material: Steel Function: Designed for attaching a hanger rod to be centered under beam flanges. 2" (50.8mm) vertical adjustment is provided in the clamp. Approvals: Conforms to Federal Specification WW-H-171E & A-A-1192A, Type 21 and Manufacturers Standardization Society ANSI/MSS SP-69 & SP-58, Type 21. Finish: Plain or Electro-Galvanized Order By: Part number, flange width, and finish.
PAGE 7
Beam Clamps B3054 - Malleable Iron Beam Clamp With Extension B3054WO - Malleable Iron Beam Clamp Without Extension (TOLCO Fig. 329) Size Range: 3/8"-16 thru 7/8"-9 rod Clamping Rod and Nuts Included Material: Malleable Iron Function: Designed for attaching a hanger rod to the bottom flange of a beam. Adjustable for flange widths of 3" (76.2mm) to 7" (177.8mm) and a flange thickness of no greater than 5/8" (15.9mm). Approvals: Underwriters Laboratories Listed.
PAGE 8
Beam Clamps B3291, B3292, B3293, B3294, B3295, B3296, B3297, B3298 UFS Beam Clamp With Weldless Eye Nut Available with left hand threads by adding an L to part number Example: B3291L-* Size Range: 3/8"-16 thru 2"-41/2 rod C C Material: Forged Steel Function: Designed for attaching a hanger rod to the bottom flange of a beam. Adjustable from flange widths of 3" (76.2mm) to 15" (381.0mm). and flange thickness of no greater than 11/32" (26.2mm).