XR8 WASH XR8 WASH (Cod. 03.MW001.L) • Electromagnetic ballast 230V 50/60 Hz • Black colour XR8 WASH (100V) (Cod. 03.MW001.100.L) • Electromagnetic ballast 100V 50/60 Hz • Black colour XR8 WASH (120V) (Cod. 03.MW001.120.L) • Electromagnetic ballast 120V 50/60 Hz • Black colour User’s Manual Rel 1.1 GB D.T.S. Illuminazione srl - ITALY http://www.dts-lighting.
XR8 WASH ARC 1200 Le informazioni contenute in questo documento sono state attentamente redatte e controllate. Tuttavia non è assunta alcuna responsabilità per eventuali inesattezze. Tutti i diritti sono riservati e questo documento non può essere copiato, fotocopiato, riprodotto per intero o in parte senza previo consenso scritto della D.T.S. DTS si riserva il diritto di apportare senza preavviso cambiamenti e modifiche estetiche , funzionali o di design a ciascun proprio prodotto. D.T.S.
XR8 WASH ARC 1200 INDEX: 1- TECHNICAL FEATURES 2- IMPORTANT SAFETY INFORMATION 4 5 2.1 Fire prevention 2.2 Prevention of electric shock 2.3 Protection against ultraviolet radiation 2.4 Safety 2.5 Level of protection against the penetration of solid and liquid matter 3- MOUNTING THE LAMP 6 3.1 Lamp alignment 4- VOLTAGE AND FREQUENCY 5- INSTALLATION 7 7 5.1 Safety cable 5.2 Protection against liquids 5.3 Movement 5.4 Risk of fire 5.5 Forced ventilation 5.
XR8 WASH ARC 1200 1- TECHNICAL FEATURES The XR8 Wash is fitted with a Philips MSR 575/2 discharge lamp (GX9,5 lampholder base), with a colour temperature of 7,200 °K and a luminous flux of 49,000 Lumens. Duration is 750 hours, with replacement recommended before 1000 hours Other recommended lamps: Philips 575 MSD (6.000K°-49.000 Lumens-3.000 hours) The unit incorporates: Motorized zoom (20°-45°), rotating and indexable beam shaper (0°-180°), frost filter, 2 colour conversion filters (3.200°K and 5.
XR8 WASH 2- IMPORTANT SAFETY INFORMATION 2.1 Fire prevention: XR8 uses a Philips 575 MSR/2 or MSD The use of any other alternative lamp is not recommended and will null and void the fixture's warranty. -Never locate the fixture on any flammable surface. -Minimum distance from flammable materials: 1 MT. -Minimum distance from the closest illuminable surface: 2 MT. -Replace any blown or damaged fuses only with fuses of identical value. Refer to the wiring diagram if there is any doubt.
XR8 WASH 6 3- MOUNTING THE LAMPS Warning: Switch off the unit before replacing the lamp. Philips 575 MSR/2 Power 575W Luminous flux 49,000 lm Colour temperature 7.200°K Lampbase GX9,5 Rated life 1,000 hours Philips 575 MSD Power 575W Luminous flux 43,000 lm Colour temperature 6.000°K Lampbase GX9,5 Rated life 3,000 hours 1) Using a screwdriver, remove the 3 screws A,B, C, (photo 1) which fix the lamp holder. Photo 1 Photo 2 Photo 3 Photo 4 2) Remove the lamp holder assembly (photo2).
XR8 WASH 4- VOLTAGE AND FREQUENCY The XR8 with electromagnetic ballast can operate at 230 V 50-60 Hz (Standard) On request: 100 V 50-60 Hz /120 V 60 HZ 5- INSTALLATION XR8 may be either floor or ceiling mounted. For floor mounting installations, the XR8 is supplied with four rubber mounting feet on the base. For ceiling mounted installations, we reccomend the use of appropriate clamps to fix the unit to the mounting surface.
XR8 WASH 8 5.3- Movement The projector has a maximum movement of 540° for Pan and 270° for Tilt. DO NOT place any obstructions in the path of the projector's movement. 270° 540° 5.4- Risk of fire Each fixture produces heat and must be installed in a well-ventilated place. The minimum recommended distance from flammable material is 1 MT. Minimum distance from the object being illuminated is 2 MT. 5.
XR8 WASH Ensure that the conductors do not touch each other.Do not connect the cable ground to the XLR chassy The plug housing must be isolated. Connect the mixer signal to the DMX IN projector plug and connect it to the next projector by connecting the DMX OUT plug on the first projector to the DMX IN plug of the second one. In this way, all the projectors are cascade connected. NB.
XR8 WASH 7.1-DMX Addresses XR8 Wash have 16 DMX channels. Set the following addresses on the mixer: Projector 1 Projector 2 A001 A017 Projector 3 ….. projector 6 A033 A…. A081 If you want to select the next projector, just add “16” 7.2-Selecting the DMX address 1) Press the UP-DOWN key until you reach the required DMX channel. The numbers on the display will start to flash (but the new DMX address hasn't yet been set). 2) Press ENTER to confirm your selection.
XR8 WASH 11 8- DISPLAY FUNCTIONS MAINS Electronic ballast 90-245V 50 / 60Hz Electromagnetic ballast 230 V 50/60 Hz (standard) On request: 100 V 50-60 Hz 120 V 60 HZ / 208 V 60 Hz DISPLAY DMX IN DMX OUT UP MENU DOWN ENTER DISPLAY FUNCTIONS The XR8 display panel shows all the available functions . Using these functions, it is possible to change some of the parameters and add some functions.
XR8 WASH 12 8- DISPLAY FUNCTIONS MENU Up-Down ENTER Up-Down TEST MODE Full test and single function test. ALL MAGENTA PAN YELLOW TILT EFFECTS DIMMER ZOOM SHUTTER COLOR CYAN MENU Up-Down ENTER Up-Down RESET Al motors reset MENU Up-Down RESET ENABLED VIA DMX RESET DISABLED VIA DMX ENTER TOTAL RESET ENTER ENTER ENTER DEFAULT To restore default setting MENU Up-Down ENTER SOFTWARE Software version MENU Up-Down Pcb 8 motors.
XR8 WASH 13 8- DISPLAY FUNCTIONS MENU Up-Down ENTER ON / OFF VIA DMX (default) Up-Down ENTER LAMP Lamp always ON-always OFF Or lamp ON-OFF selectable via DMX ENTER ENTER ADJUST To adjust the lamp with no mixer connected.
XR8 WASH 9- PAN & TILT SPEED (SPEE) (default: 2) You can set the PAN and TILT motors at high speed on your XR8. Press menu until you see SPEE. Press ENTER and select a speed with UP-DOWN (there are 4 speeds). Confirm by pressing ENTER. When you use speed 4 (the highest) PAN and TILT speed is very high and your projector may loose its path. In this case, the encoder corrects the position. 10- FAN SPEED (FANS)( default: 12) Fan speed regulation makes it possible to reduce fan noise.
XR8 WASH 15 12- HIDDEN MENU For technical personnel only. To operate this menu: -Connect the projector to the DMX controller (DMX SIGNAL MUST BE CORRECTLY RECEIVED) - Reset the XR8 (reset from the MENU, not from the DMX controller!). - While reset is running, press the MENU and ENTER keys at the same time. Electronic calibration of the motors. Reset EEPROM (Reset all settings. ATTENTION: by pressing this key you must repeat all previous calibrations) Exit from hidden menu. 16 ES.
XR8 WASH 13- OPENING THE PROJECTOR HOUSING It is possible to inspect the inside of the projector by removing the cover as indicated below. ATTENTION REMOVE MAINS POWER PRIOR TO ACCESSING THE PROJECTOR’S INTERNAL COMPONENTS. 1) Loosen the 3 (1/4 turn) screws which fix the head covers (photo 1) . 2) Once unscrewed, simply lift the covers to access the internal components (photo 2). 14- PERIODIC CLEANING Photo 1 Photo 2 14.
XR8 WASH 17 16- DMX PROTOCOL 16 CHANNEL MODE ( 16bit) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 PAN msb (540°) PAN lsb TILT msb(320°) TILT lsb MOVEMENT SPEED DIMMER SHUTTER COLOUR CYAN MAGENTA YELLOW SPEED CMY / DIMMER MACRO CMY / COLOUR EFFECTS ZOOM RESET DMX CHANNEL 1 Parameter: PAN msb 540° DMX CHANNEL 2 Parameter: PAN lsb DMX CHANNEL 3 Parameter: TILT msb 319° DMX CHANNEL 4 Parameter: TILT lsb DMX CHANNEL 5 Parameter: MOVEMENT SPEED DMX range Value Mid point DMX value Move range (degre
- XR8 WASH ARC 1200 - 18 DMX CHANNEL DMX range Value 7 Parameter: SHUTTER Mid point DMX value Move range (degrees) Mode Option 0-9 10-23 24-37 38-51 52-65 66-79 80-93 94-107 108-121 122-135 136-149 150-163 164-177 178-191 192-205 206-219 220-227 228-233 234-255 DMX CHANNEL DMX range Value 0-12 13-25 26-38 39-51 52-64 65-77 78-90 91-103 104-116 117-129 130-142 143-155 156-168 169-181 182-197 198-200 201-203 204-206 207-209 Function Black-out Strobe random speed Strobe speed 1 min.
- XR8 WASH ARC 1200 19 210-212 213-215 216-218 219-221 222-224 225-228 229-231 232-234 235-237 238-240 241-243 244-246 247-249 250-252 253-255 DMX CHANNEL DMX range Value Right rotation speed 5 Right rotation speed 6 Right rotation speed 7 Right rotation speed 8 Right rotation speed 9 min Stop Left rotation speed 1 min. Left rotation speed 2 Left rotation speed 3 Left rotation speed 4 Left rotation speed 5 Left rotation speed 6 Left rotation speed 7 Left rotation speed 8 Left rotation speed 9 max.
- XR8 WASH ARC 1200 20 DMX CHANNEL 13 DMX range Value Mid point DMX value 0-9 10-14 15-19 20-24 25-29 30-34 35-39 40-44 45-49 50-54 55-59 60-64 65-69 70-74 75-79 80-84 85-89 90-94 95-99 100-104 105-109 110-114 115-121 122-128 129-135 136-142 143-149 150-156 157-163 164-170 171-177 178-184 185-191 192-198 199-205 206-212 213-219 220-226 227-233 234-240 241-247 247-255 Parameter: MACRO CMY / COLOUR Move range (degrees) Mode Option Function No Function Macro 1 Macro 2 Macro 3 Macro 4 Macro 5 Macro
- XR8 WASH ARC 1200 21 DMX CHANNEL DMX range Value 14 Parameter: EFFECTS Mid point DMX value Move range (degrees) Mode Option 0-19 20-39 40-255 No effect Frost Beam Shape DMX CHANNEL DMX range Value Function 15 Parameter: ZOOM Mid point DMX value Move range (degrees) Mode Option 0-225 Function Proportional DMX CHANNEL 16 Parameter: LAMP / RESET MODE 1 (DEFAULT) DMX range Value Mid point DMX value 0-9 10-60 61-129 130-179 180-200 201-239 240-255 5 30 95 154 190 220 247 Move ra
- XR8 WASH ARC 1200 22 17- COLOUR WHEEL 3 2 4 5 1 6 8 COL1 0507K004 CONV.FILTER CTO TC3256 COL2 0507K003 CONV. FILTER CTB DL542 COL5 COL6 0507C042.D01 GREEN WB5055 0507C047.D01 RED LW 640 7 COL3 COL4 0507C046.D01 WOOD SW 460 0507C051.D01 ORANGE LW590 COL7 COL8 0507C041.D01 0507C053.
XR8 WASH 18- MOTORS CONTROL CARD 8 MOTORS CONTROL CARD J7 Magnetic Sensors Connector Line 1 Brown: Line 2 Orange: Zoom motor1 (BLACK) GND ORANGE BROWN VCC Zoom motor2 (DARK GREEN) Strobe (YELLOW) Colour wheel (PINK) J1 Internal DATA Communication Connector From J8 Pan & Tilt card + Effects 30 VDC (GREY) Magenta (LIGHT BLUE) Cyan (GOLD) Yellow (BLUE) Fans Fans
XR8 WASH ARC 1200 24 19-PAN & TILT CARD PAN (WHITE) TILT (BROWN) GND (BLACK) 30 VDC (RED) FAN (WHITE) ENCODER PAN (RED) MOTOR TILT (BROWN) DATA 2 (LIGHT GREEN) DATA 1 (VIOLET) ENCODER TILT (ORANGE) TO CN5 CN6 LAMP ON-OFF CARD TO J1 DISPLAY CARD (WHITE) TO J1 8 MOTORS CARD (VIOLET) DMX INPUT (WHITE) 20-CABLES RESEND CARD ENCODER TILT (ORANGE) DISPLAY 2 DISPLAY 1 21-DISPLAY CARD FROM J12 PAN&TILT CARD BLACK RED BLACK BLACK IN LAMP 22-LAMP ON-OFF CONTROL CARD V1 OUT LAMP CN7 If the
NOTES XR8 WASH ARC 1200
NOTES XR8 WASH ARC 1200
NOTES XR8 WASH ARC 1200
The information contained in this publication has been carefully prepared and checked. However, no responsibility will be taken for any errors. All rights are reserved and this document cannot be copied, photocopied or reproduced, in part or completely, without prior written consent from D.T.S..D.T.S. reserves the right to make any aesthetic, functional or design modifications to any of its products without prior notice. D.T.S.