TDS

DRYLOK® E1 1-Part Epoxy Floor Paint 50 g/L
DRYLOK® E1 1-Part Epoxy Floor Paint utilizes
an Advanced Epoxy Ester Resin fortied
formulation for greater protection and
durability.
Resists hot tire pick-up, chemicals, oil, grease
and gasoline stains
Formulated using Advanced Epoxy Ester
Resin for a durable finish
Easy to maintain
UV-resistant semi-gloss finish
Specially formulated to protect and beautify
interior and exterior concrete oors, garage
oors, basement oors, walkways and patios.
DRYLOK E1 is not recommended for oors
previously painted with 2 component epoxy
paints or for commercial or industrial use.
COMPOSITION:
Epoxy ester/acrylic blend
SHEEN:
Semi-gloss
Surface appearance depends upon
condition and porosity of
concrete/masonry surface. Highly
porous masonry/concrete may require
additional coats to achieve full gloss.
% WEIGHT SOLIDS:
238 Platinum: 42.76%
237 Gray: 43.51%
284 Tint Base: 42.46%
% VOLUME SOLIDS:
238 Platinum: 33.89%
237 Gray: 34.10%
284 Tint Base: 33.81%
DENSITY (LBS./US GAL.):
238 Platinum: 9.53
237 Gray: 9.62
284 Tint Base: 9.49
VISCOSITY:
80 ± 3 Ku
pH:
8.0-9.0
COLORS:
• Available in Tint Base
• 2 ready mixed colors
DRY TIME:
• To touch: 30 minutes-1 hour
• To recoat: 4 hours
• Light use: 4 hours
• Heavy use: 24 hours
• Vehicular traffic: 5-7 days
• Maximum resistance properties: 3-5
days.
Note: Maximum cure and dry time will
be prolonged when slightly humid and
damp, cool conditions prevail.
CLEAN UP:
Soap and water
Dispose of contaminated absorbent,
container and unused contents in
accordance with local, state and federal
regulations.
COVERAGE (SQ. FT./US GAL.):
• 300-400 sq. ./gal.
Note: Actual coverage will vary
depending upon application method,
surface texture and porosity.
RECOMMENDED FILM THICKNESS/COAT:
• 4-5 wet mils/coat
FLASH POINT:
N/A
SHELF LIFE:
5 Years
FREEZE/THAW:
Stable
CONTAINER SIZES:
One gallon (US)
Does not exceed 50 g/L
Do not add more than 12  oz of universal
tinting colorant per gallon.
e success of your project is dependent
upon the degree of surface preparation
provided. Surface must be clean and free
from dirt, dust, grease, oil, soap, wax, concrete
curing membranes and the oily lm le by
sweeping compounds. Stains on the surface
should be removed using UGL DRYLOK
Concrete Cleaner & Degreaser or a heavy
duty detergent until the surface is clean. Rinse
thoroughly with clean water and allow to dry
completely. If using a pressure washer, do not
use on a pressure seing above 1750 psi to
avoid damaging the concrete. Remember
concrete acts like a “stone sponge.” Pressure
washing and cleaning in general may trap
residual moisture in the concrete.
Check for Trapped Moisture: Tape a 12” x
12” piece of 3 mil plastic or aluminum foil
tightly on all four edges to the surface.
Remove it aer 24 hours. If the oor side of
the plastic or foil is damp allow additional
drying and then repeat the test. A
dehumidier or fan may help to eliminate
residual trapped moisture.
e concrete to be painted should have a
slight texture, such as the look and feel of
medium grit sandpaper or a broom nish. A
®®
UNITED GILSONITE LABORATORIES
MAILING: P.O. Box 70, Scranton, Pennsylvania, 18501
SHIPPING: 1396 Jefferson Avenue, Dunmore, Pennsylvania, 18509
T
OLL FREE: 1-800-UGL-LABS (845-5227)
P
HONE: 1-570-344-1202 • FAX: [phone]
www.ugl.com
D R Y L O K ® M A S O N R Y P R O D U C T S
O V E R
DRY TIME:
Recoat 4 Hours
CLEAN-UP:
Soap and Water
COVERAGE:
2 Coats Maximum
SPREAD RATE:
300-400 Sq.
Ft./Gallon