TDS

DRYLOK® Floor & Wall Masonry Waterproofer (formerly Clear Masonry Waterproofer)
DRYLOK® Floor & Wall Masonry
Waterproofer is the rst non-pigmented
masonry waterproofer specically
formulated for use on bare masonry oor
and wall surfaces. Provides a durable,
waterproof, easy to clean, non-yellowing
high gloss nish. DRYLOK® Floor & Wall
Masonry Waterproofer incorporates
biocides, to resist the growth of mold and
mildew on the dry paint lm. Resists 4 PSI,
greater than a wall of water 9 feet (2.7
meters) high! Fully transferable 7 year
warranty.
Clear high-gloss waterproof coating
Exterior-wall water repellent
Stops hydrostatic pressure
Resists 98 MPH wind-driven rain
High abrasion resistance
Provides moisture/vapor barrier to floors
prior to applying a adhesive and flooring
Use as a finish coat or use under latex
paint
Resists wear from foot traffic
Complies with current VOC requirements
It’s perfect for waterproong interior and
exterior concrete oors, poured concrete
walls, split-faced block, concrete and
cinder block, stone, brick, stucco, and pre-
cast decorative items.
Not recommended for automobile traffic.
Hydrostatic performance dependent on
achieving recommended lm thickness.
COMPOSITION:
Latex
SHEEN:
High gloss
% WEIGHT SOLIDS:
30% ± 2%
DENSITY (LBS./US GAL.):
8.69 ± 0.2 lbs. (1.04 g/L)
VISCOSITY:
120-130 Ku @ 77ºF (25ºC)
pH:
8.5-9.0
COLORS:
Clear
DRY TIME:
• To touch: 2 hours
• To recoat walls: 2 hours
• Light foot traffic: 4 hours
• Heavy foot traffic: 24 hours
• Under oor covering: 24 hours
Note: Maximum cure and dry time
will be prolonged when slightly
humid and/or damp, cool conditions
prevail.
CLEAN UP:
Soap and water.
Dispose of contaminated absorbent,
container, and unused contents in
accordance with local, state, and
federal regulations.
COVERAGE (SQ. FT./GAL.):
First coat: Wet: 18 Dry: 4.9 mils @
90 sq. ./gal.
Second coat: Wet: 14 Dry: 3.8 mils
@ 114 sq. ./gal.
Note: Actual coverage will vary
depending upon application
method, surface texture, and
porosity.
RECOMMENDED FILM THICKNESS/COAT:
Average 16 wet mils/2 coats
(406 microns). See COVERAGE.
SHELF LIFE:
3 Years unopened container
FREEZE/THAW:
Protect from freezing (passes 3
cycles)
CONTAINER SIZES:
One gallon (3.785 L) and ve gallon
(18.9 L) containers
Does not exceed 100 g/L
N/A
Do not thin.
Best results are obtained when applied
over dry surfaces. Wait for a dry (rain-
free) period for application. Surface must
be clean and free from dirt, dust, grease,
oil, form release compound, or paint.
Patch all holes and cracks, especially the
oor/wall joint with DRYLOK® Fast Plug®, a
fast seing hydraulic cement or use a
patching compound which matches the
original surface color and smooth the
patch evenly with the surface around it.
EFFLORESCENCE, a white, powdery,
crystal-like deposit visible on the masonry
surface must be removed.
DRYLOK® Etch (liquid or powder) or
muriatic acid, used according to
manufacturer’s directions, are effective
UNITED GILSONITE LABORATORIES
MAILING: P.O. Box 70, Scranton, Pennsylvania, 18501
SHIPPING: 1396 Jefferson Avenue, Dunmore, Pennsylvania, 18509
T
OLL FREE: 1-800-UGL-LABS (845-5227)
P
HONE: 1-570-344-1202 • FAX: [phone]
www.UGL.com
D R Y L O K ® M A S O N R Y P R O D U C T S
O V E R
S
o
a
p
DRY TIME:
2 Hours
Recoat 2 Hours
CLEAN-UP:
Soap and Water
COVERAGE:
2 Coats Minimum
SPREAD RATE:
90-100 Sq.
Ft./Gallon
07 14 16 COLD FLUID-APPLIED WATERPROOFING
DIV. 07