MIRAGE-X SHOWER AND TUB DOOR INSTALLATION INSTRUCTIONS IMPORTANT DreamLine® reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical drawings, manuals, warranty information or additional details please refer to your model’s web page on DreamLine.
This model is treated with DreamLine’s exclusive ClearMaxTM Glass technology. This is a specially formulated coating that prevents the buildup of soap and water spots. Install the surface with the ClearMaxTM label towards the inside of the shower. Please note that depending on the model, the glass may be coated on either one or both surfaces. For best results, squeegee the glass after each use and dry with a soft cloth. MIRAGE-X shower and tub door manual Ver 1 Rev 5 12/2017 ©2017 DreamLine.
Table of Contents Section title Model Diagram Page # 2 Preparation Tools 3 Parts List 5-6 Installation Steps Bumpers 7-24 10-11 L-Bar 14-15 Roller Assembly 17-18, 20-21 Vinyl Seals 22 Product maintenance 24 MIRAGE-X shower and tub door manual Ver 1 Rev 5 12/2017 4 ©2017 DreamLine.
Model Diagram L- Bra 5 t cke 9 11 PAN EL DOO R 4 ©2017 DreamLine.
Preparation 1. Prior to installation, examine all boxes and packages for shipping damage and compare the piece count with your packing slip. After opening all boxes and packages read this introduction carefully. Check that all of the needed parts are included in the package by checking off the components on the “Detailed Diagram of Shower Door Components”.
Tools Level Power Drill Professional grade Glass suction cup Tape Measure Hammer Pencil Phillips Screwdriver Miter Saw or Hacksaw Razor Knife Drill bit (Ø8mm) (Ø5/16") Silicone Drill bit (Ø3mm) (Ø1/8") Carpenter’s Square Phillips extender driver bit Top Threshold must be level. Tip: Prior to installation, cover the shower/tub drain with tape to prevent losing screws or small parts. Tip: Set screw gun clutch to low setting when installing screws and bolts to prevent stripping the heads.
Detailed Diagram of Shower Door Components L-Bar (Left ) L-Bar (Right ) 6 7 5 9 1 2 10 11 12 PAN EL DOO DOOR R 4 13 EL PAN 14 15 3 16 17 18 19 20 21 Left-hand door installation ©2017 DreamLine. All Rights Reserved Right-hand door installation The glass surface with the ClearMax™ label must be installed to face inside of the shower ! NOTE: This model is available in either a shower height or a tub height. This manual will describe the installation steps showing a shower height model.
Parts List Item# PART NUMBER ITEM QTY Item# PART NUMBER ITEM QTY 01 010260003 Stationary Panel Glass 1pc 12 07121063 Bottom Rail insert 1pc 02 010260006 Door Glass 1pc 13 063007100-1804 Bumper seal strip 1pc 03 04170011-1574 Bottom Guide Rail 1pc 14 07551088 0.5mm Bottom Spacer Strip 1pc 04 07221002 Handle (203mm centers) 1pc 15 098002/098003 Allen Wrench 2.5mm,3mm 1ea 05 07121048 L - Bar™ (Left and Right) 1set 16 091105 Truss Head screw ST4.
Installation steps 1. Measure the finished opening at the top, middle and bottom. The bottom width dimension will be “W”. Also check the threshold for level and the walls for plumb. Note that this model will provide up to 3/8” of adjustment for out-of-plumb conditions within the U-Channel on the panel side only. (Fig 1) This model requires a minimum threshold width of 1-3/8” Fig 1 2. Subtract 1/16” from your “W” dimension. (W (-) 1/16” = L) “L” = finished cut length.
3. Place the Bottom Guide Rail (#03) onto the threshold and mark its position. Use a tape measure to keep Bottom Guide Rail (#03) parallel with the outside edge of the threshold. (Fig 3) threshold Fig 3 4.
5. Position the Wall Profile/U-Channel (#17) against the wall, on top of the Bottom Guide Rail (#03), and flush with the outside of the Bottom Guide Rail (#03). Adjust to plumb using a level. (Fig 5) Right-hand door installation shown Fig 5 position on the wall and also mark the hole locations for drilling. Remove the Wall Profile/ U-Channel (#17) and drill Ø5/16”(6mm) holes into the wall. Insert the Wall Anchors (#06).
NOTE: The top SafeStop™ Bumper (#11) needs to be screwed to the wall beneath the L-Bar™ (#05) and against the Wall profile/U-Channel (#17). The bottom SafeStop™ Bumper (#11) is installed with 3M tape only. Attaching the bottom SafeStop™ Bumper (#11) with a screw is optional. (Fig 10, Fig 12 and Fig 13) 11 11.2 11.1 11.4 11.3 3M tape SafeStop™ Bumper #11 parts list Phillips extender driver bit recommended for screw installation 11.1 Bumper insert 1pc 11.2 Bumper base 1pc 11.3 ST4.
8. To install the bottom SafeStop™ Bumper (#11); First, clean the area with an alcohol swab. Remove the 3M tape backing from the Bumper (#11) and install the SafeStop™ Bumper (#11) onto the Bottom Rail (#03) firmly against the wall and the Wall profile/U-Channel (#17). (Fig 8a and Fig 8b) ! NOTE: Drilling a Ø5/16” hole and using an anchor to attach the bottom Safe Stop™ Bumper (#11) is optional. 1 2 Remove the 3M tape backing inside Fig 8a u-channel ©2017 DreamLine.
9. Apply silicone into the Wall profile/U-Channel (#17) and into the Bottom Guide Rail (#03) equal to the width of the panel glass. (Fig 9) Caulk Wi Pa dth o ne f lG las s 10. Cut the 0.5mm Bottom Spacer Strip (#14) into four to five 2” pieces and place them into the Bottom Guide Rail (#03) (after the silicone) to protect the bottom edge and corners of the Stationary Panel Glass (#01). (Fig 10) (DO NOT install one long continuous strip into the bottom rail).
11. After applying silicone into the Bottom Guide Rail (#03), add the 2” pieces of the 0.5mm Bottom Spacer Strip (#14) into the Bottom Guide Rail (#03) to protect the bottom edge and corners of the Stationary Panel Glass (#01). (DO NOT install one long continuous strip). (Fig 11) Wi Pa dth o ne f lG las s Fig 11 12. Install the Stationary Panel Glass (#01) into the Wall profile/U-Channel (#17) and Bottom Guide Rail (#03).
13. After the Stationary Panel Glass (#01) is installed into the Wall Profile/U-Channel (#17), install the appropriate L-Bar™ (#05) as described in the following steps. (Fig 13) Left L-Bar™ installation shown as an example 5.4 5.5 5.6 5.7 5 5.3 5.8 5.2 5.1 L-Bar parts list 5.1 Rubber pad 2pcs 5.2 M5 rubber tip set screw 2pcs 5.3 L-Bar 1pc 5.4 Decorative cover 1pc 5.5 Wall Anchor 2pcs 5.6 Wall plate 1pc 5.7 ST4.2x40 2pcs 5.8 M5x14.5 Screw 2pcs ©2017 DreamLine.
14. Use a level and position the L-Bar™ (#05) onto the Stationary Panel Glass (#01) as shown and mark the position on the wall. Remove the Wall Plate (#5.6) and mark the holes for drilling. Drill two Ø5/16”(8mm) holes and insert the Wall Anchors (#06). Attach the Wall Plate (#5.6) using ST4.2 x 40 (#5.7) screws. (Fig 14) ! TIP: Leave the decorative cover attached when marking the L-Bar postion on the wall to allow space to re-attach the cover plate after installation.
16. Measure from the edge of the installed Stationary Panel Glass (#01) to the wall and cut the Bottom Rail Insert (#12) to this dimension: W (-) 1/16”. Use a metal file to file off any burrs from the cut end. Apply silicone into the Bottom Guide Rail (#03) and install the Bottom Rail Insert (#12). (Fig 16) W W Trim the insert to: W (-) 1/16” W 0.5mm Bottom Spacer Strip (#14) ! ©2017 DreamLine. All Rights Reserved Fig 16 NOTE: Insert a small section (1/4”+/-) of the leftover 0.
Bottom Roller Assembly (#10) Parts List 10.1 Roller body (exterior) 1pc 10.2 Rubber pad 1 2pcs 10.3 Rubber pad 2 1pc 10.4 Bearing 1pc 10.5 Adjustment disk 1pc 10.6 M5x14 Allen Bolt 4pcs 10.7 Cover plate 1pc 10.8 Decorative cover plate 1pc 10.9 M5x16 Allen Bolt 2pcs 10.6 10.9 10.8 10.6 10.5 10.4 10.3 10.2 10.1 10.7 NOTE: It is not necessary to completely disassemble the wheel assembly during installation ! NOTE: DO NOT install the handle onto the door glass until instructed.
! NOTE: Have an assistant available to hold the door glass in position during the next steps until the door is secured in position with the Guide Block Assembly (#09). 18. Set the Door Glass (#02) with the attached Bottom Roller Assemblies (#10) onto the Bottom Guide Rail (#03). Have an assistant support the Door Glass (#02) for the next few steps. (Fig 18) panel glass or the wall during installation. ©2017 DreamLine.
Guide Block Assembly (#09) Parts List 9.1 Exterior Slider Bracket (for panel) 1pc 9.2 Gasket 2pcs 9.3 Rubber sleeve 2pcs 9.4 Shaft 2pcs 9.5 Sliding pad 1pc 9.6 Sliding Guide Block (for door) 1pc 9.7 M5x10 set screw 2pcs 9.8 M4x4 flat head screw 2pcs 19. Loosen the M5x10 set screws (#9.7) to seperate the bracket. Attach the Exterior Slider Bracket (#9.1) through the notch of the installed Stationary Panel Glass (#01) as shown in Fig 19a.1, using the Gasket (#9.
20. Install the Handle (#04) to the outside of the Door Glass (#02). (Fig 20.1) 1 Attach the Bumper Seal Strip (#13) to the closing edge of the Door Glass (#02). (Fig 20.2) 2 doo r Fig 20 21. The door should operate smoothly and create a good seal with the wall when in the closed position. If necessary, adjust the Bottom Rollers (#10) as shown to tilt the door slightly for a good seal with the wall. Loosen the center M5 x 14 Allen Bolts (#10.6) and then rotate the Adjustment Disk (#10.
NOTE: Wheel assembly adjustment detail (Fig 21b) 1/16” 1/16” max. 1/4”(6.5mm) 3/16”(4.5mm) min.1/16”(2.5mm) Fig 21b Fig 22 MIRAGE-X shower and tub door manual Ver 1 Rev 5 12/2017 ©2017 DreamLine. All Rights Reserved 22. Attach the roller Cover Plates (#10.8), leaving approximately 1/16” of clearance beneath the bottom rail. Re-adjust the plate if it makes contact with the bottom rail.
23. Remove the paper strip from the adhesive backing of the Bottom Deflector (#18) and attach all three deflectors to the bottom edge of the Door Glass (#02) as shown. Notch the bottom of the Bumper Seal Strip (#13) to fit around the Bottom Deflector (#18). Attach the Anti-water side strip (#19) to the edge of the Door Glass (#02). Notch the top to fit around the L-Bar™ and notch the bottom to fit around the Bottom Deflector (#18). (Fig 23).
24. Apply a good quality, mildew-resistant silicone along the U-Channel and Bottom rail. (Fig 24) ! Allow 24 hours for the silicone to fully cure before first use. ©2017 DreamLine.
Product Maintenance BASES and BACKWALLS: To ensure long-lasting life for your acrylic back walls, wipe them off after each use with a soft cloth. To clean the acrylic back walls use non-abrasive sprays or cream based cleaners. Avoid the use of aerosol spray cleaners. Never use abrasive cleansers, metal brushes or scrapers that could scratch or dull the surface. GLASS: To ensure long-lasting life for your glass shower products, wipe them off after each use with a soft cloth.
TEL: 866-731-2244 FAX: 866-857-3638 DREAMLINE.COM For more information on DreamLine® Shower Doors and Enclosures please visit DreamLine.com ©2017 DreamLine.