AQUA-Q SWING ® d e rve INSTRUCTIONS SHOWER AND TUB DOOR iIn NSTALLATION L e s m e PLEASE REVIEW THIS ENTIRE MANUAL PRIOR TO INSTALLATION a R e Dr ghts © Ri All Model# d e e in erv L s m e a R e r s D ght © Ri All ® left-pivot door installation shown SD-373472Q-## SD-374072Q-## SD-373458Q-## ##=finish 01 - Chrome 04 - Brushed Nickel 06 - Oil Rubbed Bronze 09 - Satin Black IMPORTANT! DreamLine® reserves the right to alter, modify or redesign products at any time without prior notice for the purpose of p
d e e n v i r L e s m e a R e Dr ghts © Ri All ® Record the following purchase information for your records or in the event you need to contact DreamLine®: Purchase Order Number Store/Vendor Purchased From Installation Date OD Number (optional) Installed By: SKU Number AQUA-Q SWING Shower and Tub Door Manual Ver 1a 052021 located on the shipping box or label if available.
Section Title Page # Warnings and General Preparation Model Specific Preparation Adjustable Wall Profile System ® Tools Detailed Diagram of Aqua-Q Swing Shower Door Components Parts List Installation Steps Aluminum Threshold Dam Strip Installation Vinyl Seals Installation Handle/Towel Bar Installation Product Maintenance Troubleshooting Factory Parts Information d e e n v i r L e s m e a R e Dr ghts © Ri All d e e n v i r L e s m e a R e Dr ghts © Ri All Symbol Legend TIP NOTE ! ® TIP - for ease of
d e e n v i r L e s m e a R e r s D ght © Ri All IMPORTANT • • • DreamLine® reserves the right to alter, modify or redesign products any time without prior notice for product improvement and customer experience. Please refer to the model’s web page on DreamLine.com for the latest technical drawings, installation manuals, warranty information or additional product details.
©2021 DreamLine® All Rights Reserved Model Specific Preparation ! REQUIRED: ±0.0 d e e n v i r L e s m e a R e Dr ghts © Ri All ® 1-1/2” minimum threshold 1/2” (12mm) maximum Out-of-Plumb Adjustment within the Wall Profile; Verify threshold and walls with a level 1-1/2“ (37.5mm) minimum threshold ±0.0 ! Threshold must be level Tile Tub Acrylic L swing NOTE ®! DO NOT attach the Handle to the Door Glass until instructed. DO NOT use the handle to lift the glass during installation.
©2021 DreamLine® All Rights Reserved Adjustable Wall Profile System ! Glass Profile d e e n v i r L e s m e a R e Dr ghts © Ri All Wall Profile Glass Profile max 1/2” adju s tmen ST4.0×10mm Pan Head Screw (#05) t d e e n v i r L e s m e a R e Dr ghts © Ri All ® decorative cap (#06) Wall Profile The Glass Profiles can be adjusted up to 1/2” within the Wall Profile for overall width or to correct for out-of-plumb conditions within the model size.
©2021 DreamLine® All Rights Reserved Tools Level Drill Bit Ø1/8" (3mm) Safety Glasses Tape Measure Pencil #2 Phillips Screwdriver d e e n v i r L e s m e a R e Dr ghts © Ri All Drill Bit Ø5/16" (8mm) ® Razor Knife Work Gloves Soft Head Hammer Power Drill 100% Silicone* Professional-grade Glass Suction Cup (Optional but recommended) Verify that the correct model size has been ordered; measure the finished opening before proceeding with the installation.
©2021 DreamLine® All Rights Reserved Detailed Diagram of AQUA-Q SWING Shower Door Components 06 d e e n v i 02 er L s m e a R e r s D ght © Ri All ® 05 inside 11 d e e n v i r L e s m e a R e Dr ghts © Ri All ® 03 01 04 07 09 08 10 AQUA-Q SWING Shower and Tub Door Manual Ver 1a 052021 6
©2021 DreamLine® All Rights Reserved Parts List 01 02 03 d e e n v i r L e x1 s x1 m e a R Dre ghts © R05i 06 l l A ® (with pre-installed Glass Profile) 04 ST4.0×40mm Pan Head Screw x5 Threshold Connector 10 Threshold End Cover (left/right) ST4.
©2021 DreamLine® All Rights Reserved 1 Installation Steps NOTE 1 Check the walls for plumb and threshold for level. This model allows for up to 1/2” of out-of-plumb adjustment within the Wall Profile. The threshold must be level for correct installation. d e e n v i r L e s m e a R e Dr ghts © Ri All ® 2 3 TIP d e e n v i r L e s m e a R e Dr ghts © Ri Fig 1 l l A ® Confirm the Wall Profile (#01) is plumb with a level before marking the location of the holes for drilling.
©2021 DreamLine® All Rights Reserved 2 1 3 2 *see NOTE d e e n v i r L e s m e a R e Dr ghts © Ri All *see® NOTE 4 6 5 silicone the back of the Wall Profile Fig 2 NOTE de insi NOTE d e e n v i r L e s m e a R e Dr ghts © Ri All ® Install the Wall Profiles (#01) so that the holes face the inside of the shower. ◾If a Stud is present behind the wall: drill a Ø3/16”(4mm) hole up to the stud, drill an Ø1/8” (3mm) pilot hole into the stud and use the ST4.
©2021 DreamLine® All Rights Reserved 3 NOTE Before installing the Door Glass (with pre-installed Glass Profile), make sure the side with the ID Groove, screw holes and Vinyl Seal are facing the inside of the shower. ID Groove d e e in erv L s m e a R e r s D ght © Ri All ® 1 Screw Hole Vinyl Seal Inside of Shower 2 d e e in erv L s m e a R e r s 3t D Fig h © Rig All ® Place 1/2” (12mm) thick wood or plastic shims onto the threshold to provide proper spacing beneath the door glass.
©2021 DreamLine® All Rights Reserved 3a Optional Step ! NOTE This optional step requires drilling into the threshold, which may have warranty implications in the case of some prefabricated shower pans. If in doubt, check the shower pan manufacturer’s warranty. If additional stability is desired for the Bottom Pivot Bracket, it can be screwed to the threshold. This is not a necessary step for installation, but can be accomplished using the steps below if desired.
©2021 DreamLine® All Rights Reserved 4 Decorative Caps Installation NOTE Make sure the Door Glass is plumb and level. Drill Ø1/8” holes through the pre-drilled holes in the Wall Profile (#01). Drill only through the first layer of the Glass Profile and install the ST4.0x10mm Pan Head Screws (#05) using the Decorative Cover and Washer (#06) Do not overtighten screws.
©2021 DreamLine® All Rights Reserved Threshold Installation 5 NOTE Open the Door Glass and install the Threshold Dam Strip. 08 d e e in 2erv L s m e a R e r s t D gh © Ri l l A ® 1 3 inside inside 5 4 d e e in erv L s m e a R e r s t D gh © Ri l l A ® Fig 5 NOTE This product is shipped with both a left and right Dam Strip Clip installation. The large curved lip of the dam strip is intended to face toward the outside of the shower to ensure the flow of water is redirected towards the drain.
©2021 DreamLine® All Rights Reserved 6 Vinyl Seals Installation d e e n v i r L e s m e a R e Dr ghts © Ri All ® d e e n v i r L e s m e a R e Dr ghts © Ri All ® Inside Fig 6 Parts Needed 09 x1 AQUA-Q SWING Shower and Tub Door Manual Ver 1a 052021 13
©2021 DreamLine® All Rights Reserved 7 Handle/Towel Bar Installation TIP Be sure to use all the gaskets correctly to prevent any metals to glass contact.
NOTE ©2021 DreamLine® All Rights Reserved 8 The surfaces need to be clean and free of debris before applying silicone d e e in erv L s m e a R e r s D ght © Ri l l A ® d e e n v i r L e s m e a R e r s D ght © Ri l l A ® Fig 8 ! Allow 24 hours for the silicone to cure before using the shower AQUA-Q SWING Shower and Tub Door Manual Ver 1a 052021 Tools Needed 15
©2021 DreamLine® All Rights Reserved Product Maintenance BASES and BACKWALLS: To ensure long lasting life for your acrylic back walls: wipe them off after each use with a soft cloth. To clean the acrylic back walls use non-abrasive sprays or cream based cleaners. Avoid the use of aerosol spray cleaners. Never use abrasive cleansers, metal brushes or scrapers that could permanently scratch or dull the surface.
©2021 DreamLine® All Rights Reserved Troubleshooting Problem/Symptom Suggested Solution Page(s) • Check all shipping/packaging material for missing parts/components. Missing Parts • If not found, contact DreamLine Customer Support [1-866-731-2244] to order factory part replacement.
©2021 DreamLine® All Rights Reserved Factory Parts Information AQUA-Q FOLD {SD-373472Q-##} ITEM # 01 02 03 04 05 06 07 08 09 10 11 FACTORY PART NUMBER 04280011-1828 220540102 07552148 091107 091101 07551011 07551057/07551058 04092011-0787 063015060-0799 07551077/07551078 07221035 FACTORY PARTS INFORMATION ITEM DESCRIPTION Left and Right Wall Profile for 1/4" Thick Glass Hinge and Door Assembly d e e n v i r L e s m e a R e Dr ghts © Ri All ® Wall Anchor 8mm (5/16”) ST4.0 x 40mm Pan Head Screw ST4.
©2021 DreamLine® All Rights Reserved Factory Parts Information AQUA-Q FOLD {SD-374072Q-##} ITEM # FACTORY PART NUMBER 01 04280011-1828 02 220540101 03 07552148 04 091107 05 091101 06 07551011 07 07551057/07551058 08 04092011-0939 09 063015060-0951 10 07551077/07551078 11 07221035 FACTORY PARTS INFORMATION ITEM DESCRIPTION Left and Right Wall Profile for 1/4" Thick Glass Hinge and Door Assembly Wall Anchor 8mm (5/16”) ST4.0 x 40mm Pan Head Screw ST4.
©2021 DreamLine® All Rights Reserved Factory Parts Information AQUA-Q FOLD {SD-373458Q-##} ITEM # FACTORY PART NUMBER 01 04280011-1472 02 220540103 03 07552148 04 091107 05 091101 06 07551011 07 07551057/07551058 08 04092011-0787 09 063015060-0799 10 07551077/07551078 11 07221035 FACTORY PARTS INFORMATION ITEM DESCRIPTION Left and Right Wall Profile for 1/4" Thick Glass Hinge and Door Assembly Wall Anchor 8mm (5/16”) ST4.0 x 40mm Pan Head Screw ST4.
©2021 DreamLine® All Rights Reserved NOTES: d e e in erv L s m e a R e r s D ght © Ri All ® d e e in erv L s m e a R e r s D ght © Ri All ® AQUA-Q SWING Shower and Tub Door Manual Ver 1a 052021 21
d e e in erv L s m e a R e r s D ght © Ri All ® d e e in erv L s m e a R e r s D ght © Ri All ® TEL: 866-731-2244 FAX: 866-857-3638 DREAMLINE.COM For more information on DreamLine® Shower Doors and Enclosures please visit DreamLine.