OCEANA Shower Cabin Installation Instructions IMPORTANT Please read carefully the following instructions before installing your shower cabin. If you have any questions on this shower cabin installation - please call our technical support specialists Monday to Friday 9:00AM – 5:00PM EST at 1-866-731-8378 Option 3 or e-mail our technical support group at support@BathAuthority.
Preparation 1. After opening all the boxes, read this introduction carefully, check all the packed parts are complete by cross checking all the components against the “Detailed Diagram of Shower Cabin Components”. Examine for shipping damage. If the unit has been damaged or has a finishing defect, please contact your local distributor within 3 business days.
Detailed Diagram of Shower Cabin Components 2 1 9 10 11 4 12 13 6 7 14 8 15 16 5 3 Packing List 01 02 03 Back panel Roof Bottom tray 1 pc 1 pc 1 pc 04 Vertical post 2 pcs 05 Guide rail with attached 2 pcs stoppers Stationary glass 2 pcs Glass door 2 pcs Handles 2 pairs Magnetic strip 2 pcs Anti-water strip 4 pcs 06 07 08 09 10 11 12 13 14 15 16 17 18 19 Seal gasket U shape gasket M6×20 bolt set with nuts, washers Flat head self tapping screw ST4.
Cabin Installation 1. Choose the location where you will be installing the tray, mark the location of the tray because you may need to move it out from the position for better assembling procedure. Check on the drain if it is fastened tight enough to make sure it won’t leak after complete tray installation. 2. Also сheck all the hose connections to prevent leakage. Your plumber may want to replace the drain flex hose to hard PVC pipes which is also possible (instructions are provided in the manual). 3.
or problems; open each valve to see how it works, check thermostatic valve for hot and cold water. You may need to tight some connections (during storage and transportation connections may get loose). If you do not see any leakage, then you can move it to the permanent position, attach the front skirting panel and finish your project. One of the ways on how to change flex hose to hard PVC pipes: Disconnect the flex hose from the shower drain unit. Fasten the 1 ½” hard PVC pipe to the drain.
Fig 2 Fig 3 Rev. 1.1.
Fig 5 Fig 7 Rev. 1.1.
Fig 9 Fig 11 Rev. 1.1.
Fig 13 Fig 14 Using controls ● ● ● ● ● Valve “a” turns on water of the “tropical rain” head shower. Valve “b” turns on water of seven massage jets. Valve “c” turns on water of the hand shower. Turn the revolve cover of the shower head will change water pattern. Valve “d” turns on the tub filler Valve “e” turns on the foot massager. Thermostatic valve “f” adjusts water temperature on any valves you are using. b d OFF e OFF OFF OFF 113 100 2 12 86 F Rev. 1.1.
Product maintenance Acrylic cleaning. Acrylic should be cleaned with warm water and a clean, nonabrasive cloth. If desired, a mild, nonabrasive detergent may also be used. Use only light pressure when cleaning. Avoid rubbing dirt or grit into the surface. Turn the cloth often and replace with a clean cloth frequently. Dry by blotting gently with a clean, dry cloth. DO NOT USE window cleaning sprays, alcohol, kitchen abrasive compounds, or solvents (such as acetone, gasoline, or thinners).
Bath Authority™ LLC / DreamLine™ Shower Enclosure, Jetted/Steam Shower and Shower Columns Limited Warranty CONSUMER RESPONSIBILITIES Your DreamLine™ Shower Products will remain beautiful for many years if you take care of them. Some of the waterproofing plastic strips and other seals will need to be replaced when they show signs of wear, yellowing, or are not watertight. Refer to the parts list of your manual for all seals.