Shower Door and Shower Base Kit Installation Instruction IMPORTANT at any time without prior DreamLine TM reserves the right to alter, modify or redesign products notice. For the latest up -to-date technical drawings, ma nuals or any other details please refer to the support.BathAuthority.com web page. STEP 1: Install Shower Base Shower Base Installation Instructions STEP 2: Install Shower Door Shower Door Installation Instructions Please read these instructions carefully before installing.
FLEX SHOWER DOOR INSTALLATION INSTRUCTIONS IMPORTANT DreamLineTM reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical drawings, manuals or any other details please refer to the support.BathAuthority.com web page. Please read these instructions carefully before installing.
Preparation 1. After opening all boxes and packages, read this introduction carefully. Check that all of the needed parts are included in the package by marking all the components on the “Detailed Diagram of Shower Door Components”. Examine boxes and packages for shipping damage. If the unit has been damaged, has a finishing defect, or is missing parts, please contact our customer support department within 5 business days of the delivery date.
Detailed Diagram of Shower Door Components 1 3 2 1 4 5 6 13 7 8 Part List 01 02 03 04 05 Wall profile Door assembly Wall anchor Round head screw ST4.2x10 Round head screws ST4.2×40 2pcs 1set 8pcs 8pcs 8pcs 06 07 08 13 Decorative cover Flanged anti-water strip Bottom anti-water strip Handle 8pcs 1pc 1pc 1pc NOTE: Unpack your unit carefully and inspect it. Lay it out and identify all parts using detailed diagram and packing list in your manual as a reference.
Door Assembly Diagram Alluminum profile Stationary glass Expandable rail Glass door Alluminum profile Expandable rail “FLEX” Rev.2, Ver.
Shower Door Installation NOTE: The installation of this door requires two installers. NOTE: The door can be installed on the shower base or custom threshold. 1. Prior to the Shower door installation, Shower base installation and plumbing must be completed. See Fig. 1 for details. W Fig. 1 2. Push the Wall profiles (01) over the Door assembly (02) on both sides. Be sure that the flanges with predrilled holes are pointing in towards the shower. 1 See Fig. 2 & Fig. 3 for details. 2 Fig. 2 “FLEX” Rev.
NOTE: Flip the entire assembly for opposite installation. Fig. 3 3. Move the Door assembly (02) with the Wall profiles (01) on the Shower base with Stationary glass side tight to the wall. Pull Glass door side of the Door assembly by stretching top and bottom Expanding rails to extend the Door assembly towards the opposite side of the wall.
4. Level the Door assembly (02) vertically using a level. See Fig. 5 for details. Fig. 5 5. Have second installer hold the Door assembly (02) in the correct position; mark the wall through the predrilled holes on the flange of the Wall Profiles (01). 1 See Fig. 6 for details. Inside 2 Outside Inside Fig. 6 “FLEX” Rev.2, Ver.
6. Set the Door assembly (02) aside; drill the holes using Ø5/16” drill bit and insert the Wall anchors (03). 1 Ø 5/16” See Fig. 7 for details. 2 Fig. 7 1 7. Apply silicone along the Wall Profiles (01) and around the holes on the wall. Place the Wall Profiles back on the Shower base into correct position and secure them to the walls using the Round head screws ST4.2×40 (05). See Fig. 8 and Fig. 9 for details. 2 3 Fig. 8 “FLEX” Rev.2, Ver.
1 2 3 Fig. 9 8. Place the Door assembly (02) back onto the Shower base. See Fig. 10 for details. Fig. 10 “FLEX” Rev.2, Ver.
9. Install the Handle (13) onto the Door assembly (02). Insert the Door assembly (02) with the Stationary glass side into the Wall profile (01). 1 See Fig. 11 for details. 2 Fig. 10 Fig. 11 10. Extend the Door assembly (02) toward the other wall and insert Glass door side into the Wall profile (01). See Fig. 12 and Fig. 13 for details. Fig. 12 “FLEX” Rev.2, Ver.
Fig. 13 1 11. Make sure the Door assembly (02) is fully extended inside the Wall profiles (01). Adjust top and bottom Expanding rails to the same length. Use a tape measure for accuracy. See Fig. 14 for details. 2 Fig. 14 “FLEX” Rev.2, Ver.
1 12. Drill holes in top and bottom Expanding rails through the predrilled holes using Ø 1/8” drill bit. Ø 1/8" ATTENTION: Do not drill the Expanding rail throughout, only the first layer. Ø 1/8" Secure the Expanding rails using Round head screws ST4.2×10 (04) with the raised white washers. Cover exposed screw heads with Decorative covers (06). See Fig. 15 for details. 13. Do the final adjustments of the Door assembly (02) in the Wall profiles (01).
. Attach Flanged Anti-water strip (07) to the vertical edge of the Stationary glass. Cut Bottom Anti-water strip (08) in two pieces to cover the bottom edge of the door from pivot to both sides of the Glass door. Attach both pieces of the Bottom Anti-water strip to the bottom edge of the Glass door. 1 Outside See Fig. 17 for details. 2 Fig. 17 15.
Product Maintenance To ensure long lasting life for your acrylic back walls, wipe them off after each use with a soft cloth. To clean the acrylic back walls use non-abrasive sprays or cream based cleaners. Never use abrasive cleansers, metal brushes or scrapers that could scratch or dull the surface. To ensure long lasting life for your glass shower products, wipe them off after each use with a soft cloth. Rinse and wipe off the glass using either soft cloth or squeegee to prevent soap buildup.
SLIMLINE SHOWER BASE SHOWER BASE DIMENSIONS AND INSTALLATION INSTRUCTIONS IMPORTANT DreamLineTM reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical drawings, manuals or any other details please refer to your model’s web page on BathAuthority.com Please read these instructions carefully before installing.
Preparation 1. Prior to installation, examine all boxes and packages for shipping damage and compare the piece count with your packing slip. After opening all boxes and packages, read this introduction carefully. Check that all of the needed parts are included in the package by checking off the components on the “Detailed Diagram of Shower Door Components”.
SINGLE THRESHOLD SHOWER BASE Center Drain Configuration W W1 11 D1 D MODEL SPECIFICATION D (in) W (in) D1 (in) W1 (in) DLT-1132320 DLT-1136360 32"×32" 36"×36" 32" 36" 32" 36" 15" 15" 16" 18" DLT-1134420 34” x 42” 34” 42” 15” 21” DLT-1132480 DLT-1136480 DLT-1130600 DLT-1132600 DLT-1134600 DLT-1136600 32"×48" 36"×48" 30"×60" 32"×60" 34"×60" 36"×60" 32” 36" 30" 32" 34" 36" 48” 48" 60" 60" 60" 60" 15” 15" 15" 15" 15" 15" 24” 24" 30" 30" 30" 30" “SLIMLINE SHOWER BASE” Ver.5 Rev.
SINGLE THRESHOLD SHOWER BASE Left-Hand Drain Configuration W W1 D1 D MODEL SPECIFICATION D (in) W (in) D1 (in) W1 (in) DLT-1130601 DLT-1132601 DLT-1134601 DLT-1136601 30"×60" 32"×60" 34"×60" 36"×60" 30" 32" 34" 36" 60" 60" 60" 60" 15" 15" 17" 18" 12" 12" 12" 12" “SLIMLINE SHOWER BASE” Ver.5 Rev.
SINGLE THRESHOLD SHOWER BASE Right-Hand Drain Configuration W W1 D1 D MODEL SPECIFICATION D (in) W (in) D1 (in) W1 (in) DLT-1130602 DLT-1132602 DLT-1134602 DLT-1136602 30"×60" 32"×60" 34"×60" 36"×60" 30" 32" 34" 36" 60" 60" 60" 60" 15" 15" 17" 18" 12" 12" 12" 12" “SLIMLINE SHOWER BASE” Ver.5 Rev.
NEO ANGLE SHOWER BASE W C C A W B A MODEL SPECIFICATION W (in) A (in) B (in) C (in) DLT-2036360 DLT-2038380 DLT-2040400 DLT-2042420 36"×36" 38"×38" 40"×40" 42"×42" 36" 38" 40" 42" 18 5/16" 20 5/16" 22 5/16" 24 5/16" 25" 25" 25" 25" 12" 12" 14 3/8" 14 3/8" “SLIMLINE SHOWER BASE” Ver.5 Rev.
QUARTER ROUND SHOWER BASE W C C W R MODEL SPECIFICATION W (in) C (in) R (in) DLT-7033330 DLT-7036360 DLT-7038380 33"×33" 36"×36" 38"×38" 33" 36" 38" 12" 12" 12" 21 5/8" 21 5/8" 21 5/8" “SLIMLINE SHOWER BASE” Ver.5 Rev.
DOUBLE THRESHOLD SHOWER BASE Corner Drain Configuration W C C W MODEL SPECIFICATION W (in) C (in) DLT-1032320 DLT-1036360 32"×32" 36"×36" 32" 36" 12" 12" “SLIMLINE SHOWER BASE” Ver.5 Rev.
DOUBLE THRESHOLD SHOWER BASE Left-Hand Drain Configuration W W1 D1 D MODEL SPECIFICATION D (in) W (in) D1 (in) W1 (in) DLT-1034481 DLT-1036481 DLT-1036601 34"×48" 36"×48" 36"×60" 34" 36" 36" 48" 48" 60" 17" 18" 18" 12" 12" 12" “SLIMLINE SHOWER BASE” Ver.5 Rev.
DOUBLE THRESHOLD SHOWER BASE Right-Hand Drain Configuration W W1 D1 D MODEL SPECIFICATION D (in) W (in) D1 (in) W1 (in) DLT-1034482 DLT-1036482 DLT-1036602 34"×48" 36"×48" 36"×60" 34" 36" 36" 48" 48" 60" 17" 18" 18" 12" 12" 12" “SLIMLINE SHOWER BASE” Ver.5 Rev.
Shower Base Cross Section Diagram Shower Base Cement board Finished Wall (2"×4") Stud Mortar Drain “SLIMLINE SHOWER BASE” Ver.5 Rev.
Shower Base Installation - Preparation 1. Ensure that the floor and the studs are at right angles. Provide a 5”×5” opening in the subfloor for the drain. The 2” PVC waste pipe should extend above the surface of the sub-floor according to the drain installation instructions and the height of the Shower base. Refer to the product drawings and tables in these installation instructions for the drain location. 90° 90° 90° See Fig. 1 and Fig. 2 for details.
2. Install the shower drain (NOT INCLUDED) according to the drain installation manual (supplied with the drain). See Fig. 3 for example Fig. 3 3. Place the tray into the designated position so that the Drain Body drops around the Drain Pipe and butt the Shower Base up against the studs. See Fig. 4 for details. Lower the base over the drain pipe and set it into place against the studs. Fig. 4 “SLIMLINE SHOWER BASE” Ver.5 Rev.
4. Level the tray and place marks on the studs above the upper edge of the tile flange. See Fig. 5 for details. Level base in two directions Fig. 5 5. Mix the bedding material (Mortar, cement-sand mix, etc.) Concrete or plaster is not recommended. Apply enough bedding material to support the entire bottom of the shower base. This will add additional stability and prevent the base from shifting position. See Fig. 6 for details. Mortar Fig. 6 “SLIMLINE SHOWER BASE” Ver.5 Rev.
6. After the bedding material has been poured and before it sets, place the shower base into the position with the drain assembly sliding over the PVC waste pipe. It will be necessary to push the shower base until the top of the tile flange aligns with the marks drawn on the studs and the front edge is contacting the rough floor along the entire length of the shower base. Ensure that the base is level in all directions.
Fig. 9 Product maintenance To ensure long lasting life for your acrylic back walls, wipe them off after each use with a soft cloth. To clean the acrylic back walls use non-abrasive sprays or cream based cleaners. Never use abrasive cleansers, metal brushes or scrapers that could scratch or dull the surface. To ensure long lasting life for your glass shower products, wipe them off after each use with a soft cloth. Rinse and wipe of the glass using either soft cloth or squeegee to prevent soap buildup.
DREAMLINE™ EXCLUSIVE LIMITED WARRANTY AS OF MAY 6, 2013 This warranty extends only to the original owner/end‐user for household use only and is not transferable to a subsequent owner. This warranty extends for a designated period of time, so long as it remains in use in its original place of installation. This warranty applies only to DreamLine products purchased from an authorized dealer in United States or Canada.
TEL: 866-731-2244 FAX: 866-857-3638 WWW.BATHAUTHORITY.COM For more information on DreamLineTM Shower Bases please visit www.BathAuthority.
