Owner`s manual

ManualsBrandsDraper ManualsDrill54443

CORDLESS DRILLS

■ STOCK No. 54441. ■ PART No. CHD96V.

■ STOCK No. 54442. ■ PART No. CRD12V.

■ STOCK No. 54443. ■ PART No. CHD12V.

■ STOCK No. 54445. ■ PART No. CHD12V2.

■ STOCK No. 54444. ■ PART No. CHD14V.

■ STOCK No. 54446. ■ PART No. CHD14V2.

■ STOCK No. 57806. ■ PART No. CHD142VPLUS.

■ STOCK No. 57807. ■ PART No. CHD182VPLUS.

06/2000

• INSTRUCTIONS •

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY TO ENSURE THE

SAFE AND EFFECTIVE USE OF THIS TOOL.

GENERAL INFORMATION

This manual has been compiled by Draper Tools and is an integrated part of the power tool equipment, which should be kept with the

machine.

This manual describes the purpose for which this tool has been designed and contains all the necessary information to ensure its correct

and safe use.We recommend that this manual is read before any operation of the machine, before performing any kind of adjustment to the

machine, and prior to any maintenance tasks. By following all the general safety instructions contained in this manual, it will ensure both

machine and operator safety, together with longer life of the tool itself.

All photographs and drawings in this manual are supplied by Draper Tools to help illustrate the operation of the machine.

Whilst every effort has been made to ensure accuracy of information contained in this manual, the Draper Tool policy of continuous

improvement determines the right to make modifications without prior warning.

Summary of content (12 pages)

PAGE 1
CORDLESS DRILLS ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ STOCK No. 54441. STOCK No. 54442. STOCK No. 54443. STOCK No. 54445. STOCK No. 54444. STOCK No. 54446. STOCK No. 57806. STOCK No. 57807. PART No. CHD96V. PART No. CRD12V. PART No. CHD12V. PART No. CHD12V2. PART No. CHD14V. PART No. CHD14V2. PART No. CHD142VPLUS. PART No. CHD182VPLUS. • INSTRUCTIONS • IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY TO ENSURE THE SAFE AND EFFECTIVE USE OF THIS TOOL.
PAGE 2
CORDLESS DRILLS ■ STOCK No.54441. ■ STOCK No.54442. ■ STOCK No.54443. ■ STOCK No.54445. ■ STOCK No.54444. ■ STOCK No.54446. ■ STOCK No.57806. ■ STOCK No.57807. ■ PART No.CHD96V. ■ PART No.CRD12V. ■ PART No.CHD12V. ■ PART No.CHD12V2. ■ PART No.CHD14V. ■ PART No.CHD14V2 ■ PART No.CHD142VPLUS. ■ PART No.CHD182VPLUS. CONTENTS: Page No. Specification/Guarantee ...........................................................................................1 – 2 Safety warning ........................................
PAGE 3
-2- 13,000 max. 10mm 3 ⁄ 8 x 24UNF Speed........................................ Impact blows per min. ............. Chuck capacity......................... 1 hr. approx. 230V 1.8kg. 1 hr. approx. Charging time .......................... Charger input voltage .............. Weight - machine only ............. Charging time .......................... CHD12V2 54445 As above, but supplied with 2 battery packs .................................................. .....................................
PAGE 4
GENERAL SAFETY INSTRUCTIONS FOR POWER TOOLS WARNING Please read the following instructions carefully, failure to do so could lead to serious personal injury. IMPORTANT Draper Tools Limited recommends that this machine should not be modified or used for any application other than that for which it was designed. If you are unsure of its relative applications do not hesitate to contact us in writing and we will advise you. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14.
PAGE 5
ADDED SAFETY INSTRUCTIONS FOR CORDLESS POWER TOOLS Safety is a combination of operator common sense and alertness at all times when the drill is being used. WARNING For your own safety do not attempt to use your drill until the battery is fully charged. Remember the drill is always in an operating condition as it does not need to be connected to a power supply. When not in use place the direction of rotation switch in the neutral position.
PAGE 6
POWER SUPPLY CONNECTING YOUR MACHINE TO THE POWER SUPPLY: (240V) To eliminate the possibility of an electric shock your machine has been fitted with a BS approved, non rewireable moulded plug and cable which incorporates a fuse, the value of which is indicated on the pin face of the plug. Should the fuse need to be replaced an approved BS1362 fuse must be used of the same rating, marked thus . The fuse cover is detachable, never use the plug with the cover omitted.
PAGE 7
UNPACKING AND CHECKING CONTENTS WARNING: For your own safety, never connect the plug to the power supply until all the assembly steps have been completed and you have read and understood the safety and operating instructions. FIG.A ✕✌ Cordless drill. ✖✌ Battery charger complete with BS approved moulded plug and cable. ✗✌ Battery pack. ✘✌ Carrying case. ✙✌ Extra battery pack. (Supplied with CHD12V2, CHD14V2, CHD142VPLUS and CHD182VPLUS). FIG.
PAGE 8
GETTING TO KNOW YOUR CORDLESS DRILL/CHARGER ✓ ✮✌ ✖ ✴✌ CHD96V - CHD14V2 ✓ ✖ CHD142V Plus - CHD182V Plus ✱✌ ✬✌ ✫✌ WARNING: Please ensure the Battery Pack is installed correctly before charging. ✭✌ ✪✌ ✲✌ ✳✌ ✯✌ ✰✌ FIG.B ✪✌ TRIGGER - When the variable speed trigger switch is depressed the chuck will rotate (providing the direction switch is in a clockwise or anticlockwise position). ✫✌ FORWARD/REVERSE LEVER - This lever determines the direction of rotation of the chuck, i.e.
PAGE 9
OPERATION BATTERY CHARGING To charge the battery pack it must first be removed from the drill. To release the battery pack squeeze the grips located on either side of the battery casing and gently pull the battery pack from the housing (fig.1). Plug the battery charger unit into a 230V/A.C. 13 amp, three-pin socket. For the CHD96V, CRD12V, CHD12V, CHD12V2, CHD14V & CHD14V2 place the battery in the charger as shown in (fig 2A).
PAGE 10
OPERATION cont’d ... CHANGING SPEEDS To change the speed of the chuck, push the two-speed gearbox selection switch ✫✌, (fig. 6 and 7) forwards for low speed, or backwards for high speed. IMPORTANT: ONLY CHANGE SPEED WHEN THE MACHINE HAS STOPPED. TRIGGER When the trigger is depressed the chuck will rotate (provided the direction switch is set in the forward or reverse position). This trigger switch is electronic which enables the user to vary the speed continuously in both gears.
PAGE 11
OPERATION cont’d ... DRILLING WOOD AND PLASTIC To prevent splitting around the drill holes on the reverse side, place a piece of scrap timber under the material to be drilled. DRILLING MASONRY Start drilling at a low speed to prevent the drill bit from wandering. Once penetration is achieved fully depress the trigger to achieve maximum speed and hammer power. DRILLING METAL Metals such as sheet steel, aluminium and brass may be drilled.
PAGE 12
DRAPER TOOLS LIMITED, Hursley Road, Chandler's Ford, Eastleigh, Hants. SO53 1YF. England. Tel: (023) 8026 6355. Fax: (023) 8026 0784. HELPLINE (023) 8049 4344 www.draper.co.uk e-mail: sales@draper.co.uk YOUR DRAPER STOCKIST ©Published by Draper Tools Ltd. No part of this publication may be reproduced, stored in a retrieval system or transmitted in any form or by any means, electronic, mechanical photocopying, recording or otherwise without prior permission in writing from Draper Tools Ltd.