ASSEMBLY INSTRUCTIONS Single Door Floor Cabinet ADULT ASSEMBLY REQUIRED This product requires assembly by an adult because of small parts. Care should be taken in unpacking and assembling this item to keep small parts away from children. During assembly children should be kept away from the product due to possible risk of injury. WARNING SEE FULL WARNING ON PAGE 2 Young children can be seriously injured or killed if furniture tips over.
THIS CABINET WILL HOLD UP TO 25 POUNDS PER SHELF OR A TOTAL OF 75 POUNDS. DO NOT LOAD EACH SHELF WITH MORE THAN 25 POUNDS OR 75 POUNDS TOTAL WEIGHT. IF OVERLOADED WITH MORE THAN 25 POUNDS PER SHELF OR 75 POUNDS TOTAL WEIGHT CABINET MAY TIP FROM WALL AND CAUSE SERIOUS INJURY OR DEATH.
PARTS LIST NO QTY DESCRIPTION 1 2 3 4 5 6 7 8 9 10 11 12 13 1PC 1PC 1PC 1PC 1PC 1PC 1PC 1PC 1PC 1PC 1PC 1PC 1PC Top Board Left Side Panel Right Side Panel Cross Bar Back Board Door Adjustable Shelf Bottom Board Drawer Front Board Drawer Left Side Panel Drawer Right Side Panel Drawer Back Board Drawer Bottom Board
NO A B C D E F G H I J K L PARTS QTY DESCRIPTION 10PCS Cam Bolt (5x35mm) 10PCS Cam Lock (15x10mm) 4PCS Wood Dowel 1PC Magnet 6PCS Screw (3x14mm) 1PC Adjustable Anchor Bracket 1PCS Screw (3x10mm) 4PCS Shelf Holder 4PCS Screw (4x35mm) 1PC Magnet Plate 2PCS Door Pin 2PCS Screw (4x25mm) M N O 2PCS Knob 1PC Screw (4x30mm) 1PC Plastic Anchor P Q R S T U V W X 4PCS Plastic Bracket 4PCS Cam Bolt (5x25mm) 4PCS Cam Lock (12x10mm) 8PCS Screw (3x12mm) 1PC Drawer Slide (attac
STEP 1 1. 2. 3. 4. 5. Screw 4 cam bolts (A) into cam bolt holes on top board (1). Attach 1 metal bracket (F) to top board (1) by inserting 1 screw (X) through hole on metal bracket (F) and tighten to top board (1). Attach magnet plate (J) to door (6) by inserting 1 screw (G) through hole on magnet plate (J) and tighten to door (6) Attach 1 knob (M) to door (6) by inserting 1 screw (L) through hole on door (6) and tighten to knob (M). Insert 2 door pins (K) into holes on door (6). STEP 2 1. 2. 3. 4.
STEP 3 1. 2. 3. 4. Attach magnet (D) to cross bar (4) by inserting 2 screws (E) through holes on magnet (D) and tighten to cross bar (4). Insert 2 wood dowels (C) into wood dowel holes on left side panel (2). Attach cross bar (4) and bottom board (8) to left side panel (2) by inserting wood dowels (C) into wood dowel holes on cross bar (4) and bottom board (8). Insert 3 cam locks (B) into cam lock holes on cross bar (4) and bottom board (8), then rotate clockwise to secure cam bolts in place. STEP 4 1.
STEP 5 1. 2. 3. Insert 2 wood dowels (C) into wood dowel holes on cross bar (4) and bottom board (8). Attach right side panel (3) to cross bar (4) and bottom board (8) by inserting wood dowels (C) and cam bolts (A) into wood dowel holes and cam lock holes on cross bar (4) and bottom board (8). Insert 3 cam locks (B) into cam lock holes on cross bar (4) and bottom board (8), then rotate clockwise to secure cam bolts in place. STEP 6 1. 2. 3.
STEP 7 1. 2. 3. Screw 4 cam bolts (Q) into cam bolt holes on drawer front board (9). Attach drawer left side panel (10) and drawer right side panel (11) to drawer back board (12) by inserting 4 screws (I) through holes on drawer left side panel (10) and drawer right side panel (11), then tighten to drawer back board (12). Slide drawer bottom board (13) into grooves on drawer left side panel (10), drawer right side panel (11) and drawer back board (12). STEP 8 1. 2. 3.
STEP 9 1. Attach drawer slide (V) and (W) to bottom of assembled drawer by inserting 4 screws (S) through holes on drawer slide (V) and (W), then tighten to bottom of assembled drawer. STEP 10 1. 2. Insert 4 shelf holders (H) into holes on left side panel (2) and right side panel (3), making sure all 4 shelf holders (H) are on same level. Place adjustable shelf (7) onto shelf holders (H).
STEP 11 1. Attach 4 brackets (P) to back of cabinet by inserting 4 screws (E) through holes on brackets (P) and tighten to cabinet. STEP 12 Option #1: Securing to Drywall 1. Position cabinet against wall in desired location. Using a pencil, make small mark on wall through hole on bracket (F). Move cabinet away from wall and screw 1 plastic anchor (O) into wall on pencil mark. 2. Place cabinet against wall, insert 1 screw (N) through hole on metal bracket (F), then tighten to plastic anchor (O).
ATTENTION ADULTS: Cabinet should be checked periodically for damage or loose screws/parts. Take appropriate action necessary to correct hazards such as tightening of screws and taking any damaged parts away from children. WARNING Please make sure your item is secured to the wall, per assembly instructions. CARE INSTRUCTIONS: Wipe clean with a water dampened cloth. Wipe dry with clean cloth. IMPORTANT: Keep assembly instructions for future reference.
Enjoy your new Cabinet! Thank you for purchasing thisHome item. We hope you enjoy it and consider purchasing other items.