User's Manual
Car Fast Wireless Charger
USER MANUAL
Features:
Attentions: Attentions: Attentions:
What is included:
Parameters:
Car holder with wireless charging fuction,
charges your phone conveniently when
driving
Power output 10W, compatible with all
phones with QI standard.
Full 360 degrees rotation for perfect
viewing angle.
Start charging once as the phone contact
with the holder, no need cable anymore.
Fix foot support to t any size of phone,
much convenient for use.
QC 3.0 USB car charger included so you
can start charging readily, with over
temperature, over current, over voltage
muti-safety protection.
Car Fast Wireless Charger
X 1
Air vent mount
X 1
X 1
cableUSB
QC3.0 car charger
X 1
Clamp arms
stretchable
range 59-85mm
Micro USB port
Transmitter coil
Infrared Sensor Wireless Charger Holder
Parameters:
Product specication:
LED Mode:
Air Vent Mount
There are three levels of locking for dierent
size AC vent blades.
2.5-3.5mm
1.8-2.5mm
Within 1.8mm
Wireless holder
10W
DC 5V/9V
Input voltage
Output power
115-205KHZ
2AInput current
Frequency
QC 3.0 car charger
5V 3A, 9V 2A, 12V 1.5A
DC 12-24V
Input voltage
Output Current
Working state LED light color
Power transfer
Red,blue,red blue light turn
on by turns for once,then o
Standby mode Light o
Charging Red light keeps on
FOD Warning Red light keeps ashing
Charge complete Red light keeps on
Attentions:
Please use the product correctly according
to instructions
Please do not disassemble the product or
throw it to re and water, to avoid leakage
caused by electrical short circuit
Please do not use wireless charger in high
temperature, wet, corrosive environment, to
avoid leakage from caused by damaged circuit
Please do not put wireless charger close to
cards with magnetic stripes or chips (ID card,
credit card etc.) to avoid demagnetization
Please keep wireless charger at least 20 CM
distance away from implantable medical device
(heart pacemaker, Implantable cochlea etc.)
to avoid potential interferences
Please do safekeeping, do not let your kids
treat wireless charger as toy to avoid unwanted
accidents
The pictures only supplies the reference, please
take the actual product as the standard
2. Insert the ball into the
socket at the back of
bracket and tighten.
1. Insert the adjuster into
the ball joint adapter.
3. Insert the mount directly
into the car air vent blade,
set the locking switch to
proper position.
6. Press the switch which
behind the bracket,
open the bracket.
5. Connect the other end
to car charger, then
insert the car charger to
car cigar lighter.
4. Connect the cable micro
head to your charge
holder.
FCC Warning:
This device complies with part 15 of the FCC Rules.Operation is
subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this
device must accept any interference received, including
interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority
to operate the equipment. This equipment has been tested and
found to comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential
installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of
the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure
requirement. The device can be used in portable exposure
condition without restriction.
FCC RF exposure statement:
The equipment complies with FCC Radiation exposure limit set
forth for uncontrolled environment.
This equipment should be installed and operated with minimum
distance 20cm between the radiator and your body.
Loose First position
Second position Third position
Please read the instructions carefully before using.
Pictures are for reference only, Specifications are
subject to the physical product
Support foot
Qi disabled devices with wireless receiver or
wireless charging case.
（Require receiver compliant with WPC Qi
standard to match).
Compatible devices:
Work well with:
Samsung Note 8, Note 9, iPhone XS MAS, Huawei P30 Pro, MIUI9,
Samsung S10+, iPhone 8PLus, Samsung S9+, Samsung S8+,
iPhone XR, Samsung S10, Samsung S7edge, Samsung S8,
iPhone XS, iPhone X, Samsung S9, iPhone 8
Also work with all other Qi enabled devices.
7. Press the clamping
arm and the phone
starts charging.
FCC ID: 2APCQ-TAC-117