OSMO MOBILE 2 User Manual v1.0 2018.
Searching for Keywords Search for keywords such as “battery” and “install” to find a topic. If you are using Adobe Acrobat Reader to read this document, press Ctrl+F on Windows or Command+F on Mac to begin a search. Navigating to a Topic View a complete list of topics in the table of contents. Click on a topic to navigate to that section. Printing this Document This document supports high resolution printing.
Contents Using this Manual 2 Legend 2 Download the DJI GO App 2 Introduction 4 Charging the Osmo Mobile 2 5 Mounting and Balancing a Mobile Phone 5 Mounting the Mobile Phone Horizontally 5 Mounting the Mobile Phone Vertically 7 Using the Osmo Mobile 2 8 Controls and Operations 8 Operation Modes 11 DJI GO App 13 Installing the DJI GO App 13 Connecting to the DJI GO App 13 Key Pages 14 Updating the Firmware 17 17 How to Update Specific
Introduction Equipped with 3-axis stabilization and SmoothTrack technology, the OSMOTM Mobile 2 turns your mobile phone into a smart motion camera by stabilizing it during movement. Its light and ergonomic design puts seamlessly smooth video creation at your fingertips. A mobile phone can be mounted to the Osmo Mobile 2 either horizontally or vertically. It is easy to use and in Follow mode allows you to position your phone by hand.
Charging the Osmo Mobile 2 To charge the Osmo Mobile 2, connect a USB adapter (not included) to the Charging port using the provided power cable. During charging the battery level indicators blink to indicate the current battery level. The battery is fully charged when the battery level indicators turn solid white. With the battery fully charged, the Osmo Mobile 2’s max run-time is 15 hours*.
2. Turn the mobile phone over (so that it is facing downwards) and adjust the position of the phone (in the holder) to balance the tilt axis. The tilt axis is balanced if the mobile phone remains level when released. 3. Adjust roll axis balance by loosening the Balance Adjustment knob and pulling out the Adjustable Arm. The roll axis is balanced if the mobile phone remains level when released. Left 1 2 If the roll axis tilts to the left, pull out the arm until the roll axis remains level.
Mounting the Mobile Phone Vertically 1. To mount the mobile phone vertically, loosen the Holder Lock knob and rotate the mobile phone holder 90 degrees. 1 90° 2 2. Place the mobile phone in the mobile phone holder while pulling the sides of the holder outwards, then release the sides of the holder so they hold the phone in place. Hold the Osmo Mobile 2 horizontally and adjust the position of the phone (in the holder) to balance the tilt axis.
Using the Osmo Mobile 2 Controls and Operations The buttons on the handle allow fine control over the gimbal and mobile phone. The gimbal converts joystick movements into smooth pan and tilt transitions, and uses SmoothTrack technology to reduce the impact of natural vibrations. In Follow mode the mobile phone can also be positioned directly by hand. 1. Power/Mode Button Press and hold the Power/Mode button for 1.5 seconds to power the Osmo Mobile 2 on/off.
2. Battery Level Indicators With the Osmo Mobile 2 powered off, press the Power/Mode button once to check the battery level. Battery Level Indicators : LED is on. LED1 : LED is blinking. LED2 : LED is off. LED3 Battery Level* 67% - 100% 34% - 66% 16% - 33% 1% - 15% 0% * Battery level indications should be taken for reference only. Low High 3. System Status LED Indicates the current system status of the Osmo Mobile 2.
4. Joystick Move vertically to tilt the mobile phone. Move horizontally to pan the mobile phone. Joystick control direction can be set in the DJI GO app. 5. Shutter/Record Button Press the Shutter/Record button once to start or stop recording, or to take a photo. (To switch between photo and video modes tap the Photo/Video switch in the DJI GO app). Press and hold the Shutter/Record button for burst capture (available on iOS only). 6. Zoom Slider Push up/down to zoom in/out. 7.
Operation Modes The figures below depict the operation modes when using the Osmo Mobile 2 with a mobile phone mounted horizontally; the same operation modes apply when using with a mobile phone mounted vertically. Upright Mode Upright mode can be used without any user input. In this mode, press the Power/Mode button twice quickly to center the mobile phone.
Flashlight Mode Rotate the Osmo Mobile 2 forward 90 degrees to go from Upright mode to Flashlight mode. To make the mobile phone vertical press the Power/Mode button twice quickly. In Flashlight mode, pushing the joystick up and down tilts the gimbal and pushing the joystick left and right has no effect. With a mobile phone mounted vertically, do not center the mobile phone in Flashlight mode if doing so will cause the end of the mobile phone to collide with the gimbal.
DJI GO App Watch a live HD video feed on your mobile screen through the DJI GO app. The app also allows you to use the ActiveTrack, Timelapse, and Pano functions, or configure camera and gimbal settings in just a few taps. Installing the DJI GO App Download the DJI GO app as described in the Using this Manual section and install it on your mobile phone. Connecting to the DJI GO App 1. Enable Bluetooth and turn off portrait orientation lock on your mobile phone to allow horizontal screen display. 2.
Key Pages Equipment > Camera 1 14 13 12 11 2 3 10 4 9 5 8 6 7 1. Connection Status Indicates the status of the connection between the DJI GO app and the Osmo Mobile 2. 2. Photo/Video Switch Slide to switch between photo and video modes. 3. Photo/Video Modes Current Photo Mode Single shot, 2s, 5s, or 10s intervals, or HDR (not available on some Android mobile devices). Current Video Mode Standard: Normal video based on your camera settings.
6. Playback Tap to view photos and videos. 7. Metering Mode/ActiveTrack Tap to switch between Metering mode and ActiveTrack. Metering Mode Tap on the screen for auto focus and metering, and swipe up or down to adjust the exposure. Tap and hold on the screen to lock the current exposure setting. Tap again to unlock. ActiveTrack Mark an object on your screen to track it as it moves. Tap the Record button to start recording. To adjust framing of the subject being tracked, use the Joystick.
Scene Mode SmoothTrack speed varies depending on the scene mode. In Sport mode, it is higher, while in Walk mode it is lower. Tilt Axis Lock Locks the tilt axis at the current angle when enabled. 10. Camera Preferences Set the video resolution and flash status, and enable beautification effects or onscreen composition grids. Enable Manual Adjustment for ISO, Shutter Speed and White Balance control (currently available on iOS only). 11. Home Tap to navigate to the home screen. 12.
Updating the Firmware Use the DJI GO App to update the Osmo Mobile 2 firmware. It takes approximately 10 minutes to complete an update. How to Update Ensure that the battery has at least 30% charge before starting an update. Connect the Osmo Mobile 2 to your mobile device and then launch the DJI GO app. You will be reminded if a new firmware update is available. To start updating, connect your mobile device to the Internet and follow the on-screen instructions.
Specifications General Name OSMO MOBILE 2 Model OM170 Dimensions 295×113×72 mm (folded) Weight 485 g Power Consumption 1.2 W (when steady and balanced) Controllable Range Pan: ±160°; Tilt: ±155° (with the mobile phone mounted horizontally) Mechanical Range Pan: ±170°; Roll: -90° to +70°; Tilt: ±170° Max Controllable Speed 120 °/s Mobile Phone Width Range 58.6 to 85 mm Wireless Mode Bluetooth Low Energy 4.
This content is subject to change. Download the latest version from https://www.dji.com/osmo-mobile-2 If you have any questions about this document, please contact DJI by sending a message to DocSupport@dji.com. OSMO is a trademark of DJI. Copyright © 2018 DJI All Rights Reserved.
