PARTS AND SERVICE INSTRUCTIONS FOR THE ELECTRIC FIREPLACE MODEL NUMBERS: BF33STP/DXP BF39STP/DXP Valued Customer, We are pleased that you have chosen to purchase an electric fireplace manufactured by Dimplex North America Ltd. Over the years, valuable memories will occur around the warmth and comfort of your hearth. Thank you for allowing our product to be the backdrop for those special moments.
TABLE OF CONTENTS OPERATION PAGE 3 PARTS DRAWING PAGE 6 PARTS LIST PAGE 7 WIRING DIAGRAM PAGE 8 MAIN ON/OFF SWITCH REPLACEMENT PAGE 9 PURIFIRE SWITCH REPLACEMENT PAGE 10 HEATER ON/OFF SWITCH REPLACEMENT PAGE 11 FLAME MOTOR/FLAME ROD REPLACEMENT PAGE 12 VOLTAGE SELECTOR SWITCH REPLACEMENT PAGE 14 HEATER ELEMENT REPLACEMENT PAGE 17 BLOWER MOTOR REPLACEMENT PAGE 19 TEMPERATURE LIMIT SWITCH REPLACEMENT PAGE 23 REMOTE CONTROL KIT PAGE 27 2
OPERATION MANUAL CONTROLS (WITHOUT REMOTE OPTION) PURIFIRE SWITCH The fireplace can be controlled by the manual switches located on the fireplace (FIGURE 1). Main Power Switch Main ON/OFF switch, activates the flame effect. Heater Control Switch Heater ON/OFF switch, activates heater to the high level.
BF33STP, BF33DXP, BF39STP, BF39DXP REMOTE CONTROL The remote control has a range of approximately 50ft. (15.25m). It does not have to be pointed at the fireplace and can pass through most obstacles (including walls). It is supplied with one of 243 independent frequencies to prevent interference with other units. The frequency designation is indicated on the back of the transmitter (FIGURE 3).
BF33STP, BF33DXP, BF39STP, BF39DXP RESETTING THE TEMPERTURE CUTOUT SWITCH The heater on this fireplace is protected with a safety device to prevent overheating. Should the heater overheat, a red light (Fig. 4) will be activated and an automatic cut out will turn the heater off. The heater will re-activate once the heater has cooled. The overheat cutout will be triggered if the filter is dirty. WALL MOUNTED CONTROLS The fireplace can be installed with wall mounted controls.
BF33STP, BF33DXP, BF39STP, BF39DXP 8 7 5 6 12 9 17 11 13 10 15 3 14 1 2 4 16 18 19 6
BF33STP, BF33DXP, BF39STP, BF39DXP REPLACEMENT PARTS DIMPLEX BUILT IN FIREPLACE REPLACEMENT PART 1. LOG SET 2. REFLECTOR ROD 3. GROMMET 4. FLICKER ASSEMBLY 5. BLOWER ASSEMBLY 6. BLOWER MOTOR 7. HEATER ELEMENT 8. CUTOUT 9. VOLTAGE SELECTOR 10. MAIN ON/OFF SWITCH 11. HEATER SWITCH 12. MIRROR SEMI-SILVERED 13. EXTRUSION 14. STEEL CURTAIN 15. STEEL CURTAIN ROD 16. LOWER LIGHT HARNESS 17.
BF33STP, BF33DXP, BF39STP, BF39DXP WIRING DIAGRAM 8
BF33STP, BF33DXP, BF39STP, BF39DXP If the fireplace was operating prior to servicing allow at least 10 minutes for light bulbs and heating elements to cool off to avoid accidental burning of skin. Disconnect circuit power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons. TO REPLACE MAIN ON/OFF SWITCH 1. Open the steel curtains (remove glass doors if applicable). 2. Remove the log grate retaining screws and remove the log grate. 3.
BF33STP, BF33DXP, BF39STP, BF39DXP If the fireplace was operating prior to servicing allow at least 10 minutes for light bulbs and heating elements to cool off to avoid accidental burning of skin. Disconnect circuit power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons. TO REPLACE PURIFIRE SWITCH 1. Open the steel curtains (remove glass doors if applicable). 2. Remove the log grate retaining screws and remove the log grate. 3.
BF33STP, BF33DXP, BF39STP, BF39DXP If the fireplace was operating prior to servicing allow at least 10 minutes for light bulbs and heating elements to cool off to avoid accidental burning of skin. Disconnect circuit power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons. TO REPLACE HEATER ON/OFF SWITCH (without remote control option) NOTE: Remote control kit does not have individual heater switch.
BF33STP, BF33DXP, BF39STP, BF39DXP If the fireplace was operating prior to servicing allow at least 10 minutes for light bulbs and heating elements to cool off to avoid accidental burning of skin. Disconnect circuit power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons. TO REPLACE FLAME MOTOR/FLAME ROD 1. Open the steel curtains (remove glass doors if applicable). 2. Remove the log grate retaining screws and remove the log grate. 3.
BF33ST, BF33DX, BF39ST, BF39DX, BF45ST, BF45DX If the fireplace was operating prior to servicing allow at least 10 minutes for light bulbs and heating elements to cool off to avoid accidental burning of skin. Disconnect circuit power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons.
BF33STP, BF33DXP If the fireplace was operating prior to servicing allow at least 10 minutes for light bulbs and heating elements to cool off to avoid accidental burning of skin. Disconnect circuit power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons. TO REPLACE VOLTAGE SELECTOR SWITCH (UNIT IS PERMENANTLY INSTALLED IN WALL) 1. Remove the log grate retaining screws and remove the log grate. 2.
BF33STP, BF33DXP If the fireplace was operating prior to servicing allow at least 10 minutes for light bulbs and heating elements to cool off to avoid accidental burning of skin. Disconnect circuit power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons. TO REPLACE VOLTAGE SELECTOR SWITCH (UNIT IS PERMENANTLY INSTALLED IN WALL) 15. Properly orientate the new switch and connect all of the wiring connections to the heater elements.
BF33STP, BF33DXP, BF39STP, BF39DXP If the fireplace was operating prior to servicing allow at least 10 minutes for light bulbs and heating elements to cool off to avoid accidental burning of skin. Disconnect circuit power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons. TO REPLACE VOLTAGE SELECTOR SWITCH (UNIT CAN BE REMOVED FROM WALL) 1. Remove unit from installed wall. (remove trim surround if applicable) 2.
BF33STP, BF33DXP, BF39STP, BF39DXP If the fireplace was operating prior to servicing allow at least 10 minutes for light bulbs and heating elements to cool off to avoid accidental burning of skin. Disconnect circuit power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons. TO REPLACE HEATING ELEMENTS (UNIT IS PERMENANTLY INSTALLED IN WALL) NOTE: The fireplace is equipped with two heating elements.
BF33STP, BF33DXP, BF39STP, BF39DXP If the fireplace was operating prior to servicing allow at least 10 minutes for light bulbs and heating elements to cool off to avoid accidental burning of skin. Disconnect circuit power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons. TO REPLACE HEATING ELEMENTS (UNIT CAN BE REMOVED FROM WALL) NOTE: The fireplace is equipped with two heating elements.
BF33ST, BF33DX If the fireplace was operating prior to servicing allow at least 10 minutes for light bulbs and heating elements to cool off to avoid accidental burning of skin. Disconnect circuit power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons. TO REPLACE BLOWER MOTOR / BLOWER (UNIT IS PERMENANTLY INSTALLED IN WALL) 1. Remove the log grate retaining screws and remove the log grate. 2.
14. Using a sharp utility knife, cut 3.22” off of the length of the rubber channel so the overall length is 17.33”. 15. Reassemble in the reverse order as above. NOTE: To replace the log set re-connect the logset LED wire harness to the unit, insert the front edge, pushing back down until the rear tab snaps under the back ledge and the logs are resting against the mirror.
BF39STP, BF39DXP If the fireplace was operating prior to servicing allow at least 10 minutes for light bulbs and heating elements to cool off to avoid accidental burning of skin. Disconnect circuit power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons. TO REPLACE BLOWER MOTOR / BLOWER (UNIT IS PERMENANTLY INSTALLED IN WALL) 1. Remove the log grate retaining screws and remove the log grate. 2.
BF33STP, BF33DXP, BF39STP, BF39DXP If the fireplace was operating prior to servicing allow at least 10 minutes for light bulbs and heating elements to cool off to avoid accidental burning of skin. Disconnect circuit power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons. TO REPLACE BLOWER MOTOR / BLOWER (UNIT CAN BE REMOVED FROM WALL) 1. Remove unit from installed wall. (remove trim surround if applicable) 2. Locate and remove both side trims from unit.
BF33STP, BF33DXP If the fireplace was operating prior to servicing allow at least 10 minutes for light bulbs and heating elements to cool off to avoid accidental burning of skin. Disconnect circuit power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons. TO REPLACE TEMPERATURE LIMIT SWITCH (UNIT IS PERMENANTLY INSTALLED IN WALL) 1. Remove the log grate retaining screws and remove the log grate. 2.
BF39STP, BF39DXP If the fireplace was operating prior to servicing allow at least 10 minutes for light bulbs and heating elements to cool off to avoid accidental burning of skin. Disconnect circuit power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons. TO REPLACE TEMPERATURE LIMIT SWITCH (UNIT IS PERMENANTLY INSTALLED IN WALL) 1. Remove the log grate retaining screws and remove the log grate. 2.
WARNING: Ensure wires do not come in contact with moving parts by securing wires in tie wraps. BF39ST, BF39DX, BF45ST, BF45DX If the fireplace was operating prior to servicing allow at least 10 minutes for light bulbs and heating elements to cool off to avoid accidental burning of skin. Disconnect circuit power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons.
BF33ST, BF33DX, BF39ST, BF39DX, BF45ST, BF45DX If the fireplace was operating prior to servicing allow at least 10 minutes for light bulbs and heating elements to cool off to avoid accidental burning of skin. Disconnect circuit power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons. TO REPLACE TEMPERATURE LIMIT SWITCH (UNIT CAN BE REMOVED FROM WALL) 1. Remove unit from installed wall. (remove trim surround if applicable) 2.
BF33ST, BF33DX, BF39ST, BF39DX, BF45ST, BF45DX If the fireplace was operating prior to servicing allow at least 10 minutes for light bulbs and heating elements to cool off to avoid accidental burning of skin. Disconnect circuit power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons. TO REPLACE REMOTE CONTROL KIT 1. Open the steel curtains (remove glass doors if applicable). 2. Remove the log grate retaining screws and remove the log grate. 3.
