OPG888E STUMP GRINDER User Manual SAFETY AND OPERATION INSTRUCTIONS IMPORTANT: Read safety rules and instructions carefully before operating equipment.
Table of Contents Table of Contents PART I: General Safety Rules PART II: Familiar with the STUMPGRINDER PART III: Operating the STUMPGRINDER PART IV: Maintaining the STUMPGRINDER PART V: Troubleshooting and Parts List 2 8 9 11 13 Conventions used in this manual WARNING This indicates a hazardous situation, which, if not avoided, could result in death or serious injury. CAUTION This indicates a hazardous situation, which, if not avoided, could result in minor or moderate injury.
Part I: General Safety Rules PART I: General Safety Rules Safety Labels Found on Your Unit 2
Part I: General Safety Rules Should make sure the emergency stop switch is available before every use. Or may result in serious injury even death. WARNING Read this Safety & Operating Instructions manual before you use the Stump Grinder. Become familiar with the operation and service recommendations to ensure the best performance of your machine. Propose CAUTION This machine is designed solely to grind stumps and must not be used for any other purpose.
Part I: General Safety Rules Before using the Stump Grinder NOTICE A． Operators must be fully trained before using this machine. B．User Manual is read and understood. C． Machine is positioned on level ground; all guards are fitted and in good condition. D． Teeth are in good condition and secure. E．All fasteners are checked for tightness. F．Only stumps are removed with this machine. G． Emergency stop wire is correctly connected and the switch is functional. H． Fire extinguisher is available on site.
Part I: General Safety Rules Safety for Children and Pets WARNING Tragic accidents can occur if the operator is not alert to the presence of children and pets. Children are often attracted to the machine and the grinding activity. Never assume that children will remain where you last saw them. Always follow these precautions: A. Keep children and pets at least 50 feet from the working area and ensure they are under the watchful care of a responsible adult. B. C.
Part I: General Safety Rules I. Keep combustible substances away from the engine when it is hot. J. Never cover the machine while the muffler is still hot. K. Do not operate the engine with the air cleaner or the carburetor air intake cover removed. Removal of such parts could create a fire hazard. Do not use flammable solutions to clean the air filter. L. The muffler and engine become very hot and can cause a severe burn; do not touch.
Part I: General Safety Rules N. O. P. Q. R. Use the machine only in daylight. Stay alert for hidden hazards. Keep all nuts and bolts tight and keep the equipment in good operating condition. Tow the equipment safely at 25 MPH off road only. NEVER tow on paved streets as this will damage your ATV tires. ALLWAYS take the brake off before towing. A Note to All Users List of warnings and cautions cannot be all-inclusive.
Part II: Familiar with the Stump Grinder PART II: Familiar with the Stump Grinder It may be helpful to familiarize yourself with the controls and features of the Stump Grinder. If you have any question, please contact DK2POWER at 702-331-5353 8-4 PST. TECHNICAL SPECIFICATIONS Recoil Start Electric Start Engine 14HP 4four stroke 14HP 4four stroke Power Gasoline Gasoline Wheel Diameter Cutters 14 inches 12 14 inches 12 Stump Height 12 inches 12 inches Stump Diameter Any Any Tire 13.
Part IV: Maintaining The Stump Grinder PART III: Operating the Stump Grinder It may be helpful to better familiarize yourself with the features of your Stump Grinder before beginning the steps outlined in this chapter. WARNING A. B. C. D. Read and understand all instructions, safety precautions, and/or warnings listed in “PART I: General Safety Rules” before operating the Stump Grinder.
Part IV: Maintaining The Stump Grinder Stopping 1. Let go of the bail shut off on the bow handle OR 2. Recoil Start: Slide the GAS lever to the LEFT to shut engine off. 3. Electric Start: Turn the Key to the OFF position. Operator Zone Stump Grinding NOTICE Clear area around stump to remove all rocks and stones WARNING Do not place your feet or hands into the cutting wheel area. This is a very UNSAFE and could result in injury or death.
Part IV: Maintaining The Stump Grinder PART IV: Maintaining the Stump Grinder Regular maintenance is the way to ensure the best performance and long life of your machine. Please refer to this manual and the engine manufacturer's user manual for maintenance procedures. WARNING Before performing any maintenance procedure or inspection, stop the engine, wait five minutes to allow all parts to cool. Disconnect the spark plug wire, keeping it away from the spark plug.
Part IV: Maintaining The Stump Grinder Lubrication NOTICE All Bearings of your Stump Grinder are sealed units and should have enough lubricant to last the life of your machine with normal use. Grease Zerks are installed if grease is ever needed. Use standard bearing grease. FOR ENGINE WARRANTY CONTACT YOUR NEAREST KOHLER ENGINE DEALER. VISIT WWW.KOHLERENGINES.COM AND ENTER YOU ZIP CODE IN THE FIND A DEALER SECTION.
Part VI: Troubleshooting and Parts List PART V: Troubleshooting and Parts List Most problems are easy to fix. Consult the Troubleshooting Table below for common problems and their solutions. If you continue to experience problems, contact DK2POWER in LAS VEGAS at 702-331-5353 8-4 PST WARNING Before performing any maintenance procedure or inspection, stop the engine, wait five minutes to allow all parts to cool. Disconnect the spark plug wire, keeping it away from the spark plug.
Part VI: Troubleshooting and Parts List Explosion View and parts list 14
Part VI: Troubleshooting and Parts List Ref Description Ref2 Description3 1 Stop frame 25 Clutch spacer 2 Spacer bush 26 8 holes rubber 3 Top handrail 27 Main frame 4 28 4 holes rubber 29 4 holes rubber fix 6 Brake line fixed block Brake line fixing piece, plastic handle Engine 30 External compression spring 7 Plastic battery box 31 Pin retaining sleeve 8 Tire 32 Brake cable limit plate 9 Universal wheel 33 The brake chuck 10 Flange 34 The brake pin 11 Tow hitch 3
Part VI: Troubleshooting and Parts List PLEASE DO NOT RETURN TO THE STORE YOU HAVE A 1 YEAR WARRANTY AND DK2 WILL REPLACE A DEFECTIVE PART FOR FREE CALL US AT 702-331-5353 FOR FAST WARRANTY PARTS AND QUESTIONS WHAT IS COVERED DK2 Inc. warrants to the original purchaser of any DK2 product that it will be free and clear of manufacturing defects in workmanship and materials under normal use and service for a period of one (1) year from the date of the original purchase.
