D E S IG N E R ’S IM A G E ® Store behind closed doors. Storage Cabinet Model 422704 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Need help? Visit Sauder.com to view video assembly tips or chat with a live rep. Prefer the phone? Call 1-800-445-1527. PLEASE READ AND KEEP FOR FUTURE REFERENCE. English pg 1-18 Français pg 19-21 Español pg 22-24 Share your journey! Lot #: 511088 Date Purchased: __________________ 12/08/17 Be sure to give us a ring before making any returns.
Table of Contents Part Identification Assembly Tools Required 2-3 Hardware Identification No. 2 Phillips Screwdriver Tip Shown Actual Size 4 Assembly Steps 5-18 Hammer Français 19-21 Español 22-24 Safety 25-26 Not actual size Tape Measure Warranty 27 Skip the power trip. This time. Now you know our ABCs. Part Identification å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other.
Part Identification G2 D K K F A C B J J I H J J E L 422704 www.sauder.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit. 1 ANGLE BRACKET - 5 7 10 3 HINGE - 6 8 APPLIQUE - 30 DOOR BRACKET - 1 13 2 11 HINGE BRACKET - 6 SHELF SUPPORT - 16 12 NAIL - 36 1-1/2" FLAT HEAD SCREW - 40 17 1/2" FLAT HEAD SCREW - 12 19 Page 4 9 METAL BRACKET - 2 99 LARGE 1/2" PAN HEAD SCREW - 10 www.sauder.
Look for this icon. It means a video assembly tip is available at www.sauder.com/services/tips Step 1 å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. å Fasten five ANGLE BRACKETS (1) to the SKIRT (L). Use five LARGE 1/2" PAN HEAD SCREWS (19). å NOTE: Be sure the edges of the ANGLE BRACKETS are even with the edges of the SKIRT. å Fasten the BOTTOM BRACKET (9) to the BOTTOM (E). Use two 1/2" PAN HEAD SCREWS (18).
Step 2 å Fasten the SKIRT (L) to the BOTTOM (E). Use three LARGE 1/2" PAN HEAD SCREWS (19) through the ANGLE BRACKETS on the VALANCE and into the BOTTOM. 19 LARGE 1/2" PAN HEAD SCREW (3 used in this step) L E The molding on the BOTTOM should be here. Page 6 www.sauder.
Step 3 å Fasten the VALANCES (K) to the TOP (D). Use eight 1-1/2" FLAT HEAD SCREWS (13). su rfa ce Some assembly (and snacks) required. This arrow should be pointing up. Fi ni sh ed T ON FR K D 13 1st Un fin ish ed su rfa ce 1-1/2" FLAT HEAD SCREW (8 used in this step) K D nd 2 422704 T ON FR This arrow should be pointing down. www.sauder.
Step 4 å Fasten two METAL BRACKETS (8) to the UPRIGHT (C). Use two 1/2" PAN HEAD SCREWS (18). å NOTE: Be sure the edges of the METAL BRACKETS are even with the top edge of the UPRIGHT. å Fasten the BOTTOM (E) to the UPRIGHT (C). Use two 1-1/2" FLAT HEAD SCREWS (13). Caution Do not stand the unit upright without the BACK fastened. The unit may collapse. 18 1/2" PAN HEAD SCREW (2 used in this step) 13 1-1/2" FLAT HEAD SCREW (2 used in this step) L 8 E Top edge C Page 8 www.sauder.
Step 5 å Finish fastening the BOTTOM (E) to the SKIRT (L). Use two 1-1/2" FLAT HEAD SCREWS (13). å Fasten the SHELF (F) to the UPRIGHT (C). Use two 1-1/2" FLAT HEAD SCREWS (13) å Finish fastening the SHELF (F) to the UPRIGHT (C). Use two 1/2" PAN HEAD SCREW S (18) through the METAL BRACKETS on the UPRIGHT and into the SHELF. å Then, peel four APPLIQUES (7) from the applique card and stick them over the heads of the SCREWS (13). Peel the APPLIQUES from the applique card.
Step 6 å Fasten the HINGE BRACKETS (3) to the ENDS (A and B). Use the SCREWS in the HINGE BRACKETS. å NOTE: The arrow on the HINGES should face towards the edge of the ENDS. 3 A B 3 3 Page 10 www.sauder.
Step 7 å å Fasten the LEFT END (B) to the TOP (D), BOTTOM (E), SHELF (F), VALANCES (K), and SKIRT (L). Use thirteen 1-1/2" FLAT HEAD SCREWS (13). Hey! It's starting to look like something! Finish fastening the LEFT END (B) to the SKIRT (L). Use a LARGE 1/2" PAN HEAD SCREW (19) through the ANGLE BRACKET on the SKIRT and into the LEFT END.
Step 8 å Fasten the RIGHT END (A) to the TOP (D), BOTTOM (E), SHELF (F), VALANCES (K), and SKIRT (L). Use thirteen 1-1/2" FLAT HEAD SCREWS (13). å Finish fastening the RIGHT END (A) to the SKIRT (L). Use a LARGE 1/2" PAN HEAD SCREW (19) through the ANGLE BRACKET on the SKIRT and into the RIGHT END. Edge with HINGE BRACKETS K D F K A L E 13 1-1/2" FLAT HEAD SCREW (13 used in this step) 19 LARGE 1/2" PAN HEAD SCREW (1 used for the ANGLE BRACKET) Page 12 www.sauder.
Step 9 å Carefully turn your unit over onto its front edges. Unfold the BACK (G2) and lay it over your unit. å Make equal margins along all four edges of the BACK (G2). Push on opposite corners of your unit if needed to make it "square". å Using your hammer, fasten the BACK (G2) to your unit using the NAILS (12). å NOTE: Be sure to tap NAILS into the holes that line up over the UPRIGHT (C). å Peel the backing off of each FELT DISC (20) and stick them on the edge of the ENDS (A and B).
Step 10 å Fasten the HINGES (2) to the DOORS (H and I). Use twelve 1/2" FLAT HEAD SCREWS (17). å Fasten the DOOR BRACKET (10) to the LEFT DOOR (I). Use two 1/2" PAN HEAD SCREWS (18). 17 1/2" FLAT HEAD SCREW (12 used for the HINGES) 2 I H 2 2 18 1/2" PAN HEAD SCREW (2 used for the DOOR BRACKET) Page 14 www.sauder.
Step 11 å å Carefully stand your unit upright. å å See the enlarged diagrams for adjustments. Mounting screw Fasten the DOORS (H and I) to the ENDS (A and B). Slide the HINGES on the DOORS onto the HINGE BRACKETS on the ENDS. Secure the DOORS with the mounting screw on the HINGE BRACKET. Fasten the PULLS (4) to the DOORS (H and I). Use four 5/8" MACHINE SCREWS (15). HINGE BRACKET 15 5/8" MACHINE SCREW (4 used for the PULLS) B A 4 I H 4 422704 www.sauder.
Step 12 å å Insert the SHELF SUPPORTS (11) into the hole locations of your choice in the ENDS (A and B) and UPRIGHT (C). Set the ADJUSTABLE SHELVES (J) onto the SHELF SUPPORTS. If you're doing this to help a friend, don't leave without a bite. NOTE: The lips of the ADJUSTABLE SHELVES can face either up or down in your unit. B A C 11 J J Page 16 (16 used) J J www.sauder.
Step 13 å We recommend using the FURNITURE TIPPING RESTRAINT KIT (99) for added stability. Fasten a bracket to the back edge of the TOP (D) using the 5/8" screw as shown. å å Place your unit in its final location against a wall. Follow the instructions included in the KIT to fasten your unit to the wall. Use the 5/8" screw through the small hole in a bracket and into the back edge of the TOP (D). Small hole 99 D 422704 www.sauder.
Step 14 å Peel twenty-six APPLIQUES (7) from the applique card and stick them over the heads of the SCREWS in the ENDS (A and B). å å NOTE: Please read the back pages of the instruction booklet for important safety information. This completes assembly. Clean with your favorite furniture polish or a damp cloth. Wipe dry. And to celebrate, why not share your success story? A No load Weight Limits: Top Shelf - 50 lbs. Adjustable Shelf - 25 lbs. each Bottom - 50 lbs.
DE S IG N ER ’ S I M A G E ® Modèle 422704 Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. La pièce devant être attachée à l’élément est représentée en gris sur les schémas de chaque étape pour plus de précision. Comparer la “Liste de pièces” ci-dessous avec la “PART IDENTIFICATION” du manuel en anglais pour vous familiariser avec les pièces avant l’assemblage.
ÉTAPE 1 ÉTAPE 5 Assembler l'élément sur un sol à moquette ou sur le carton vide pour éviter d'endommager l'élément ou le sol. Finir de fixer le DESSOUS (E) à la PLINTHE (L). Utiliser deux VIS TÊTE PLATE 38 mm (13). Fixer cinq CONSOLES À ÉQUERRE (1) à la PLINTHE (L). Utiliser cinq GRAND VIS TÊTE GOUTTE DE SUIF 13 mm (19). Fixer la TABLETTE (F) au MONTANT (C). Utiliser deux VIS TÊTE PLATE 38 mm (13). REMARQUE : S'assurer que les chants des CONSOLES À ÉQUERRE sont à fleur des chants de la PLINTHE.
ÉTAPE 9 ÉTAPE 12 Attention: Ne pas relever l'élément dans sa position verticale avant d'avoir fixé l’ARRIÈRE. L'élément risque de s'effondrer. Insérer les SUPPORTS DE TABLETTE (11) dans les trous choisis dans les EXTRÉMITÉS (A et B) et le MONTANT (C). Poser les TABLETTES RÉGLABLES (J) sur les SUPPORTS DE TABLETTE. Avec précaution, retourner l'élément sur ses chants avant. Déplier l'ARRIÈRE (G2) et le placer sur l'élément. Veiller à avoir des marges égales le long des quatre chants de l'ARRIÈRE (G2).
DE S IG N ER ’ S I M A G E ® Modelo 422704 Use estas instrucciones de ensamblaje en español junto con las figuras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Se destacan las figuras de cada paso con una tonalidad oscura para mostrar precisamente cual parte se debe montar a la unidad. Compare la “Lista de Part” abajo con la “Part Identification” en el folleto en inglés para familiarizarse con Las partes de ensamblaje.
PASO 1 PASO 5 Ensamble la unidad sobre un piso alfombrado o sobre el cartón vacío para evitar rayar la unidad o el piso. Termine de fijar el FONDO (E) al FALDÓN (L). Utilice dos TORNILLOS DE CABEZA PERDIDA de 38 mm (13). Fije cinco SOPORTES ANGULARES (1) al FALDÓN (L). Utilice cinco TORNILLOS GRANDE DE CABEZA REDONDA de 13 mm (19). Fije el ESTANTE (F) al PARAL (C). Utilice dos TORNILLOS DE CABEZA PERDIDA de 38 mm (13).
PASO 9 PASO 12 Precaución: No coloque la unidad en posición vertical hasta que se fije el DORSO. La unidad podría caerse. Inserte los SOPORTES DEL ESTANTE (11) en los agujeros al nivel preferido de los EXTREMOS (A y B) y el PARAL (C). Coloque los ESTANTES AJUSTABLES (J) sobre los SOPORTES DEL ESTANTE. Cuidadosamente voltee la unidad para que repose sobre los bordes delanteros. Desdoble el DORSO (G2) y colóquelo sobre la unidad.
WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following safety information. Death or serious injury may occur when children climb on furniture. A remote control, toys or other items placed on the furniture may encourage a child to climb on the furniture which could cause it to tip-over and result in serious injury or death. NEVER allow children to climb on furniture.
ADVERTENCIA Por favor use el mobiliario correcta y seguramente. El mal uso puede causar riesgos de seguridad o daño a las unidades o artículos domésticos. Lea cuidadosamente la siguiente información de seguridad. Pueden suceder lesiones graves o la muerte cuando los niños se suben en los muebles. Un control remoto, juguetes u otros artículos colocados en los muebles pueden alentar a un niño a subirse en el mueble, lo cual podría causar que se derribe y resultaría en lesiones graves o la muerte.
1-YEAR LIMITED WARRANTY 1. Sauder Woodworking Co. (Sauder®) provides limited warranty coverage to the original purchaser of this product for a period of one year from the date of purchase against defects in materials or workmanship of Sauder furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 2.
Dear Valued Customer: So, how did it go? Thanks so much for choosing Sauder® furniture. I hope the purchase and assembly process was a positive experience and you feel good about the furniture you just built. If you need assistance or want to learn more, please contact our award-winning, Ohio-based customer service team at 1-800-445-1527 or Sauder.com. Set a world record for speed? Feeling good about yourself? Nice. Get social with it on any of these quality share sites.
