9-Cube Organizer Assembly Instructions 3632 / 3633 / 3634 Tools Needed: 01- 3641 7/17
SAFETY PRECAUTIONS WARNING • This unit contains small parts which could be a choking hazard for small children. Children should be under adult supervision at all times or serious injury could occur. • Always unload unit prior to moving the unit. The weight of personal belongings can cause the unit to become unstable and either tip or collapse. Serious bodily injury and/or damage to personal belongings may occur. • Do not overload unit.
HELPFUL HINTS We recommend you protect your work surface during assembly to prevent scratching or damage to table tops, wood floors, etc. finished edge unfinished edge Unfinished edges are shaded in gray. It is important to understand how finished edges go together. Take a moment to lay out all the wood pieces and note the finished and unfinished (raw wood) edges. Arrange pieces so all finished edges are facing the same way.
HARDWARE DESCRIPTION (H1) x 20 assembly screw #10 x 1-1/2” flathead A side panel 2 B top/bottom panel 2 C horizontal divider 2 D vertical divider 6 E back panel 5 (H2) x 20 screw cover (H3) x 2 hole plug QUANTITY B (H4) x 8 long dowel (H5) x 10 short dowel D E (H6) x 60 nail E D C A E (H7) x 1 l-bracket screw #10 x 1/2” flathead (H8) x 1 wall screw #10 x 1-1/2” (H9) x 1 l-bracket D A E D E C D D B Just call 1-800-874-0008 for parts and service.
STEP 1 B (H5) x 4 short dowel 1. 2. 3. 4. Push 4 short dowels into holes of one fixed shelf. Install dowels only into one top/bottom panel (both top/bottom panels are the same.) Top/Bottom panels have six holes on one side with the middle holes going through to the other side. Unfinished edges are shaded in light gray.
STEP 2 B A (H1) x 4 assembly screw #10 x 1-1/2” flathead 1. 2. 3. 4. 6 Attach fixed shelf to one side panel. Make sure finished edges of unit are up. Attach one set of vertical dividers. Push vertical dividers onto dowels in fixed shelf. Make sure finished edges of unit are up. From opposite side of fixed shelf, secure each vertical divider with a screw.
STEP 3 C D D C (H1) x 4 assembly screw #10 x 1-1/2” flathead 1. 2. 3. 4. 5. (H4) x 8 long dowel D D Insert long dowels. Attach horizontal divider. Be sure to assemble with all finished edges to front. Push horizontal divider down over dowels. (Holes in horizontal dividers go all the way through.) Secure horizontal divider with two screws through side panel. Repeat Steps 1 & 2 to attach second set of vertical dividers.
STEP 4 B (H1) x 4 assembly screw #10 x 1-1/2” flathead 1. 2. 3. 4. 8 (H4) x 4 short dowel Insert SHORT dowels and attach top fixed shelf. Be sure to assemble with all finished edges to front. Align holes in underside of top fixed shelf and place top panel into position. Secure top panel with two screws through side panel. Secure top vertical dividers with two screws through top panel.
STEP 5 A (H1) x 8 assembly screw #10 x 1-1/2” flathead 1. Attach other side panel with provided screws. 2. Be sure to assemble with all finished edges to front.
STEP 6 E E E E E (H2) x 20 screw cover 1. 2. 3. 4. 10 (H6) x 60 nail Lay unit so finished (front) edges face down and unfinished edges face up. (Unfinished surfaces are shaded in gray.) Push screw covers onto all screw heads. Gently tap in place with hammer. Position the back panels in a staggered pattern as shown. Nail the back panels into place through the holes provided, being careful not to angle the nail.
STEP 7 stacking unit single unit (H3) x 2 hole plug (H5) x 2 short dowel 1. Install dowels or hole plugs. 2. For single unit: Insert hole plugs into top holes. 3. For stacking units: Insert dowels into top holes.
STEP 8 single unit wall stud when stacking units top panel top panel wall stud (H7) x 1 l-bracket screw #10 x 1/2” flathead (H8) x 1 wall screw #10 x 1-1/2” (H9) x 1 l-bracket 1. Align center of unit with wall stud. (All units MUST be fastened to the wall. When stacking units, the unit on the bottom must be attached to the wall first before setting another unit on top. Do not stack units more than 72” high.) 2. Place short end of L-bracket against wall/wall stud.
