a5). DESIGN HOUSE READ AND SAVE THESE INSTRUCTIONS {this photo for referents only OWNERS INSTRUCTION MANUAL FOR DUAL MOUNT FAN'S @ INSTALLATION ® OPERATION ® MAINTENANCE CAUTION isn Rie se ass Se INSTALLATION AND FAN OPERATION.
| 1 ABLE OF CONTENTS Safety Hos 2 Unpacking Your Fan 3 Material Required wf Electrical Outlet box 4 Install Mounting Bracket: 5 installing the Fan 6 Electrical connections 8 Blade Attachment: 10 Installing Light kit 11-14 Operation 15 Maintenance 16 Trouble Shooting 47 Part List 18 Page
186. SAFETY TIPS To void possible electric shook, sen off the electricity at the main fuse box of circuit. panel before you bag din the fan installation or before servicing the fan or installing accessories. CAUTION: READ ALL INSTRUCTIONS AND SAFETY INFORMATION CAREFULLY BEFORE INSTALLING YOUR FAN AND SAVE THESE INSTRUCTIONS.
UNPACKING YOUR FAN 1. Unpack your fan and check the contents. Do not discard the carton. Jf warranty replacement or repair is giver necessary the fan should be returned in original packaging. Remove all parts mind hardware. Da not lay motor housing ort its side: the decorative casting may shift. 2, Examine ll parts. Yous should have the following: @ 154 Mounting Bracket &. Downfall assembly 3, Ceiling canopy 4. Fan Housing Motor, and switch housing.
TOOLS AND MATERIALS REQUIRED *Phillips scow driver *Blade screw diver *Adjustable pliers or wrench “Step ladder “Wire cutter “Electrical tape ELECTRICAL OUTLET BOX if there Nisan existing outlet box, ensure it is. clearly marked Suitable For Fan Support. if fot, i must be replaced with an approved one. : Secure the bullet: Box (or make ‘sure the existing bok is secured) directly to the building McClure, Use appropriate fasteners and building materials.
1, INSTALL MOUNTING BRACKET To avoid possible electrical ‘shock, be. Sure ethnicity 18 tamed off at the main power panel before wiring, All wiring sinister ban accordance. with National and Total Electrical: Codes, and the ceiling fan must be grounded asa precaution against possible electrical shock.
INSTALLING THE FAN SELECT TYPE OF INSTALLATION HANG DOWN HUGER HANG DOWN STYLE 1 Slide the canopy on the down rod (Fig 8) Thread the power l¢ads from the fan through the canopy dnd downed, Take tiara care not to pull on power wires. Damage and loose connections could result from any abnormal pressure on these wires. Set down rod into down rod collar yoke, Route unt! the holes match. Being careful motto damage wiring, insert connector pity through the holes {Ses Flg: 6A.
WIDOWHOOD: SETSCREW & £ Faith Nut 3 wisp Hilario Secretive Fig? 3. Tighten motor seal-screw. Check the strength of this. connection {predesignated at factory} by holding the motor Sousing in. position and fuming the down rod counter clockwise, if this connection slips, firefighter motor setscrew and lockout: Follow the same procedures as mentioned above for download setscrew, 4: install ball info hanger bracket opening. The tab. opposite of the hanger bracket opening shield fit in stolon ball (Fig 8).
ELECTRICAL CONNECTIONS 1. Four wires are consisted 16 theretofore the fan. @® Black" Hot" Power/Live for the fan & Blue!” Hol’ Power! Live for the light kit ® White: for if Tan and the light kit ® Greengrocer & Yellow: “Ground” /Barth wire 2. ¥the fan and light are connected to the same dildo, the black and blue wires should be connected together to the blat wire in the tailing using & wire nut'to make the connection, } Nn 3. The white wire from the fan should be connected 1o.
BLADE ATTACHMENT Place screw through the blade and start the screw into the blade ami repeat this procedure without tightening the screw until alf 3 screws have been started Into the blade arn (Fig 11). As most fan use concealed screw blades arms, screws may rioting through the whole blade arms. Tighter each screw starting with center screw, Fasten blade assembly to motor with provided screws. Repeat procedures for remaining blades. (Fig.
INSTALLING GENERAL CLUSTER LIGHT KIT(OPTIONAL) Locate two wires in the switch: housing (white and blue tabled Yor light’) Connect them to the light kit wire connectors (Fig. 12) White to while Blu fo blue Secure all splices with: electrical tape to prevent connection from vibrating loose during fan operation, Carefully push all wires back into the switch housing. Her attach housing cover plate to switch Housing with the 3 screws provided.
69 HE INSTALL Remove switch. housing screws and then samovar Bottom clip of switch housing shell on fan. Locate Wo wires in the: switch "housing (white and blue. labeled “for light”), Connect them the it Kit wire connectors, White fo white Blue lo'blue Secure those wires with wire nuts in the fan, Wire Nut Carefully push all wires back into the switch housing. Then attach housing cover plate to switch housing with the 3 screws provided. Brows washers install light bulbs to the freeholder.
EGS a Bh You may purchase: a fan wile Light Pan instead of clitoris it Kit mentioned above: For any kind of Baht kit you should complete the blade installation before attaching this light Kit assembly, REMEMBER to disconnect the rain power before installing the light lat by removing the fuse or troubadour the electrical panel box Parts Identification Pull chain Glass shady The whole Right Rit assembly Includes the above parts: Locals these parts. from the package and be careful motto damage the glass shade.
¢ 9 ob LTE Sy Remove switch gouging screws and then remove bottom cap of switch housing shell on fan, igi Figs 10 Locate two wires in the switch housing (white and blue labeled “for Eight Connect than to the ght kit wire connectors (Fig. 12-2). White to white lus to blue Beauteous those wires with wire nuts in the fan. bw nuncio Bids lei Biden Span 123 Carefully push all wires back into the switch housing. Then attach housing caver plate to switch: housing with the 3 screws provided.
OPERATION 1. Restore electrical power by turning on the eclectically at thé mah fuse box. 2. Turret the wall switch. & Your fanciness two controls on therewith Sousing SPEED CONTROL Full Cheer Switch Tug gently) Pull: Speed 1 High 2 Medium 3 Low 4. Off Switch Box DIRECTION CONTROL Rovers Slide Switch {Up and down) Up for upward air flow to recirculate air upward Down fof downward air flow fora cooling effect NOTE ON FANS WITH 3 SPEEDS: 11 Poll-Medium 3. Pull-Low 4.
MAINTENANCE 1. The fan's natural movements may cause some connections fo work loose. A clicking or rattling noise is lancer sigh of loosening screws. Cheek the support connections. brackets and blade attachment twice a year, and tighten all screws as necessary. Make sure all screws attaching the glass screws are tightened: 2, Clean your fan periodically. Use only a cloy dampened with. a mild detergent solution.
RUBLE SHOOTING FAN DOES NOT START Check all fuses or circuit breakers, Replace if MISSING. z Turn off electrical power and check all wire connections’ to fan and in with Housing. 3 Make sure pull chain switch 18.00, and reverse slide switch is up or dowry, inst in the middle. 4... Ensure the Switch box. cover and check all wig colonels, if ‘the. wire connectors are loose, tighten i firmly. Fan FOUND NOISY Always take avow days’ breaking time for any new fan af medium or high sped.
FOR BLADES MODELS 5, & Dumbness taps CRE 3 3 placement Busch 1-2 Fuchsia: 3-4 Switch 2 Switch 4 Tillich 4-3 FOR 5 BLADES MODELS 104 Eta Nurtured gate vacuous | Stitch 2-4 Switch 34 Switch 21 Switch 2-4 Switch 4d i the above does not eliminate the wobble, lip & balancing Kit oh any one of blade: about the middle of blade edge. Let fan run: fit is still wobbling, strophe fan, and change the location. Repeating this procedure off the’ remaining Blades until the wobble is removed.