Indoor Fireplace - Built-in Gas Fireplace User Manual

ManualsBrandsDesa ManualsMarine RadioVANGUARD FVSA18M

WARNING: If the information in this manual is not

followed exactly, a fire or explosion may result caus-

ing property damage, personal injury, or loss of life.

— Do not store or use gasoline or other flammable

vapors and liquids in the vicinity of this or any

other appliance.

— WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use

any phone in your building.

• Immediately call your gas supplier from a

neighbor’s phone. Follow the gas supplier’s

instructions.

• If you cannot reach your gas supplier, call the

fire department.

— Installation and service must be performed by a

qualified installer, service agency, or the gas supplier.

WARNING: Improper installation,

adjustment, alteration, service, or

maintenance can cause injury or

property damage. Refer to this

manual for correct installation and

operational procedures. For assis-

tance or additional information

consult a qualified installer, ser-

vice agency, or the gas supplier.

WARNING: This appliance is for

installation only in a solid-fuel

burning masonry or UL127 factory-

built fireplace, constructed of non-

combustible material, and con-

nected to a working flue. (See page

4 for minimum flue opening.)

WARNING: This is a gas-fired appliance. It uses air (oxygen) from the room in which it is installed.

Provisions for adequate combustion and ventilation air must be provided. Refer to the

National

Fuel Gas Codes, ANSI Z233.1/NFPA 54, Section 5.3, Air for Combustion and Ventilation.

GAS LOG VENTED

DECORATIVE APPLIANCE

OWNER’S OPERATION AND

INSTALLATION MANUAL

Save this manual for future reference.

ANSI Z21.60a-2000

CSA 2.26a-2000

APPROVED

VANGUARD MODELS:

VVSA18M, VVSA24M, VVDA18M, VVDA24M and VVDA30M

FOR USE WITH LOG SETS:

Hanover Round Oak Log Models VSLR18 and VSLR24

Kingston Split Oak Log Models VDLCR18, VDLCR24 (Shown)

and VDLCR30

FMI MODELS:

FVSA18M, FVSA24M, FVDA18M, FVDA24M and FVDA30M

FOR USE WITH LOG SETS:

Arlington Round Oak Log Models FSLR18 and FSLR24

Manchester Split Oak Log Models FDLCR18, FDLCR24 and

FDLCR30

COMFORT GLOW MODELS:

Oxford Oak Log Models CVSA18M and CVSA24M

Berkshire Oak Log Models CVDA18M, CVDA24M and

CVDA30M

Amherst Oak Log Models CPVSA18M and CPVSA24M

Convertible from Natural Gas

to Propane/LP Gas

Summary of content (30 pages)

PAGE 1
GAS LOG VENTED DECORATIVE APPLIANCE TM Convertible from Natural Gas to Propane/LP Gas OWNER’S OPERATION AND INSTALLATION MANUAL VANGUARD MODELS: VVSA18M, VVSA24M, VVDA18M, VVDA24M and VVDA30M FOR USE WITH LOG SETS: Hanover Round Oak Log Models VSLR18 and VSLR24 Kingston Split Oak Log Models VDLCR18, VDLCR24 (Shown) and VDLCR30 FMI MODELS: FVSA18M, FVSA24M, FVDA18M, FVDA24M and FVDA30M FOR USE WITH LOG SETS: Arlington Round Oak Log Models FSLR18 and FSLR24 Manchester Split Oak Log Models FDLCR18, FDLCR
PAGE 2
TABLE OF CONTENTS SAFETY INFORMATION TABLE OF CONTENTS SAFETY INFORMATION ............................................................ 2 CLEANING AND MAINTENANCE ............................................ 10 LOCAL CODES ........................................................................... 3 TROUBLESHOOTING ............................................................... 11 PRODUCT IDENTIFICATION .....................................................
PAGE 3
SAFETY INFORMATION LOCAL CODES PRODUCT IDENTIFICATION UNPACKING PRODUCT FEATURE SAFETY INFORMATION PRODUCT IDENTIFICATION Continued 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 3 3 Grate Steps Do not use a blower insert, heat exchanger insert or other accessory not approved for use with this log set. The installation and provisions for combustion and ventilation air must conform with the National Fuel Gas Codes, ANSI Z233.1/ NFPA 54, Section 5.3, Air for Combustion and Ventilation.
PAGE 4
INSTALLATION Flue Opening Specifications Check Gas Type Venting Specifications for Installation INSTALLATION WARNING: The Massachusetts State Board requires all installations be performed by a Licensed Plumber or Gas Fitter. Massachusetts state code requires all vent dampers be welded open or removed. CAUTION: Do not remove the data plates attached to the burner pan. The data plates contain important warranty and safety information.
PAGE 5
INSTALLATION Installing Damper Clamp 5 5 INSTALLATION Continued INSTALLING DAMPER CLAMP Secure the damper stop clamp provided to the leading edge of the damper as shown in Figure 3. If for any reason this clamp doesn't work on your fireplace, another suitable clamp or permanent stop must be installed, or the damper blade must be cut or removed. IMPORTANT: Install equipment shutoff valve in an accessible location. The equipment shutoff valve is for turning on or shutting off the gas to the appliance.
PAGE 6
INSTALLATION Checking Gas Connections Hearth Pan Installation INSTALLATION Continued CHECKING GAS CONNECTIONS WARNING: Test all gas piping and connections for leaks after installing or servicing. Correct all leaks at once. WARNING: Never use an open flame to check for a leak. Apply a noncorrosive leak detection fluid to all joints. Bubbles forming show a leak. Correct all leaks at once. Pressure Testing Gas Supply Piping System Test Pressures In Excess Of 1/2 PSIG (3.5 kPa) 1. 2. 3. 4. 5. 6.
PAGE 7
INSTALLATION Hearth Pan Installation (Cont.) 7 7 INSTALLATION Continued 4. 5. 6. 7. 8. Using a wrench, remove gas control valve and burner inlet fitting by turning counterclockwise (see Figure 8). Remove the burner inlet fitting from the gas control assembly (see Figure 8). DO NOT remove the orifice from this fitting. The propane/LP burner inlet fitting is included in the hardware kit (see Figure 9). Be sure to use the correct orifice for your appliance.
PAGE 8
INSTALLATION Testing Burner for Leaks Adding Pan Material Installing the Grate and Logs INSTALLATION Continued TESTING BURNER FOR LEAKS 1. Grate Grate Steps Generously apply noncorrosive leak detection fluid to all connections. WARNING: Never check for gas leaks with open flame. 2. 3. 4. 5. Light the burner with the shutoff valve no more than half open and holding a match slightly in front of the pan (see Lighting Instructions, page 9).
PAGE 9
OPERATING APPLIANCE For Your Safety Read Before Lighting Curing Logs Lighting Instructions To Turn Off Gas To Appliance 9 9 OPERATING APPLIANCE WARNING: Keep flue open when operating unit. WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life. LIGHTING INSTRUCTIONS 1. 2. 3. 4. 5. A. This appliance has a pilot which must be lighted by hand. When lighting the pilot, follow these instructions exactly. B.
PAGE 10
OPERATING APPLIANCE To Turn Off Gas To Appliance INSPECTING BURNERS Pilot Assembly Burner Flame Pattern CLEANING AND MAINTENANCE OPERATING APPLIANCE Continued BURNER FLAME PATTERN TO TURN OFF GAS TO APPLIANCE Shutting Off Appliance 1. 2. Turn control knob clockwise to the PILOT position. to the OFF Press in and turn control clockwise position. Shutting Off Burner Only (pilot stays lit) Turn control knob clockwise Burner flames will be steady; not lifting or floating.
PAGE 11
TROUBLESHOOTING 11 11 TROUBLESHOOTING Note: For additional help, visit DESA International’s technical service web site at www.desatech.com. Note: All troubleshooting items are listed in order of operation. WARNING: Turn off log set and let cool before servicing. Only a qualified service person should service and repair log set.
PAGE 12
TROUBLESHOOTING TROUBLESHOOTING Continued OBSERVED PROBLEM POSSIBLE CAUSE REMEDY Pilot lights but flame goes out when control knob is released 1. Control knob not fully pressed in 2. Control knob not pressed in long enough 1. Press in control knob fully 2. After pilot lights, keep control knob pressed in 30 seconds 3. Fully open equipment shutoff valve 4. A) Contact local natural or propane/LP gas company 3. Equipment shutoff valve not fully open 4.
PAGE 13
TROUBLESHOOTING 13 13 TROUBLESHOOTING Continued WARNING: If you smell gas Shut off gas supply. Do not try to light any appliance. Do not touch any electrical switch; do not use any phone in your building. Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions. • If you cannot reach your gas supplier, call the fire department. • • • • IMPORTANT: Operating log set where impurities in air exist may create odors.
PAGE 14
ILLUSTRATED PARTS BREAKDOWN VVSA18M, VVSA24M, VVDA18M, VVDA24M and VVDA30M ILLUSTRATED PARTS BREAKDOWN VVSA18M, VVSA24M, VVDA18M, VVDA24M AND VVDA30M 9 9 10 7 12 5 11 27 17 5 22 23 6 24 4 3 20 16 13 21 15 2 19 18 14 25 8 1 26 For more information, visit www.desatech.
PAGE 15
PARTS LIST VVSA18M, VVSA24M, VVDA18M, VVDA24M and VVDA30M 15 15 PARTS LIST This list contains replaceable parts used in your log set. When ordering parts, follow the instructions listed under Replacement Parts on page 26 of this manual. KEY PART NUMBER NO.
PAGE 16
ILLUSTRATED PARTS BREAKDOWN VSLR18, VSLR24, VDLCR18, VDLCR24, and VDLCR30 ILLUSTRATED PARTS BREAKDOWN 8 HANOVER ROUND OAK LOG MODELS VSLR18, VSLR24 6 7 5 KINGSTON SPLIT OAK LOG MODELS VDLCR18, VDLCR24, AND VDLCR30 4 9 1 3 15 2 12 Kingston Split Oak Logs 13 14 10 11 Hanover Round Oak Logs For more information, visit www.desatech.
PAGE 17
PARTS LIST VSLR18, VSLR24, VDLCR18, VDLCR24, and VDLCR30 17 17 PARTS LIST This list contains replaceable parts used in your log set. When ordering parts, follow the instructions listed under Replacement Parts on page 26 of this manual. KEY PART NUMBER NO.
PAGE 18
ILLUSTRATED PARTS BREAKDOWN FVSA18M, FVSA24M, FVDA18M, FVDA24M and FVDA30M ILLUSTRATED PARTS BREAKDOWN MODELS FVSA18M, FVSA24M, FVDA18M, FVDA24M AND FVDA30M 9 9 10 7 12 5 27 11 17 5 22 23 6 24 4 3 20 16 13 21 15 2 19 18 14 25 8 26 1 For more information, visit www.desatech.
PAGE 19
PARTS LIST FVSA18M, FVSA24M, FVDA18M, FVDA24M and FVDA30M 19 19 PARTS LIST This list contains replaceable parts used in your log set. When ordering parts, follow the instructions listed under Replacement Parts on page 26 of this manual. KEY PART NUMBER FOR NO. FVSA18M FVSA24M FVDA18M FVDA24M FVDA30M DESCRIPTION QTY.
PAGE 20
ILLUSTRATED PARTS BREAKDOWN 20 FSLR18, FSLR24, FDLCR18, FDLCR24 and FDLCR30 ILLUSTRATED PARTS BREAKDOWN 8 ARLINGTON ROUND OAK LOG MODELS FSLR18, FSLR24 7 MANCHESTER SPLIT OAK LOG MODELS FDLCR18, FDLCR24 AND FDLCR30 6 4 5 1 3 9 15 2 Manchester Split Oak Logs 12 14 10 13 11 Arlington Round Oak Logs For more information, visit www.desatech.
PAGE 21
PARTS LIST FSLR18, FSLR24, FDLCR18, FDLCR24 and FDLCR30 21 21 PARTS LIST This list contains replaceable parts used in your log set. When ordering parts, follow the instructions listed under Replacement Parts on page 26 of this manual. KEY PART NUMBER FOR NO.
PAGE 22
ILLUSTRATED PARTS BREAKDOWN CVDA18M, CVDA24M and CVDA30M ILLUSTRATED PARTS BREAKDOWN 33 32 MODELS CVDA18M, CVDA24M AND CVDA30M 30 31 28 34 29 27 27 9 9 10 7 12 35 11 17 5 22 23 6 24 4 3 20 16 13 21 15 26 19 18 14 25 8 1 2 For more information, visit www.desatech.
PAGE 23
PARTS LIST CVDA18M, CVDA24M and CVDA30M PARTS LIST This list contains replaceable parts used in your log set. When ordering parts, follow the instructions listed under Replacement Parts on page 26 of this manual. KEY PART NUMBER FOR NO.
PAGE 24
ILLUSTRATED PARTS BREAKDOWN CVSA18M, CVDS24M, CPVSA18M and CPVSA24M ILLUSTRATED PARTS BREAKDOWN 28 27 MODELS CVSA18M, CVSA24M, CPVSA18M AND CPVSA24M CVSA SERIES 29 26 36 25 35 34 24 33 9 31 9 10 32 30 CPVSA SERIES 37 7 5 14 19 20 6 21 4 3 17 13 18 12 23 16 15 11 22 8 1 2 For more information, visit www.desatech.
PAGE 25
PARTS LIST CVSA18M, CVSA24M, CPVSA18M and CPVSA24M PARTS LIST This list contains replaceable parts used in your log set. When ordering parts, follow the instructions listed under Replacement Parts on page 26 of this manual. KEY PART NUMBER FOR NO.
PAGE 26
REPLACEMENT PARTS ACCESSORIES REPLACEMENT PARTS ACCESSORIES Note: Use only original replacement parts. This will protect your warranty coverage for parts replaced under warranty. Purchase these log set accessories from your local dealer. If they can not supply these accessories, call DESA International at 1-866-672-6040 for referral information. You can also write to the address listed on the back page of this manual. PARTS UNDER WARRANTY Contact authorized dealers of this product.
PAGE 27
27 OWNER'S REGISTRATION FORM In order to provide better customer service for this and future purchases, we recommend that you register your product with us. You can register online at www.desatech.com. If access to our website is not available to you, please complete this Owner’s Registration Form and mail to the address on the back of this owner’s manual. Please provide the following product information: Brand: (Comfort Glow, Vanguard, etc.) Model: (EFP33PR, VTGH33NR, etc.
PAGE 28
TAPE 28 Postage Required TM 2701 Industrial Drive P.O. Box 90004 Bowling Green, KY 42102-9004 For more information, visit www.desatech.
PAGE 29
NOTES 29 29 NOTES _______________________________________________________________________________________________ _______________________________________________________________________________________________ _______________________________________________________________________________________________ _______________________________________________________________________________________________ _______________________________________________________________________________________________ ____________
PAGE 30
WARRANTY INFORMATION KEEP THIS WARRANTY Model Serial No. Date Purchased Always specify model and serial numbers when communicating with the factory. We reserve the right to amend these specifications at any time without notice. The only warranty applicable is our standard written warranty. We make no other warranty, expressed or implied.