Installation Guide

ManualsBrandsDelta ManualsBathroom Sink FaucetsT3561LF-SSWL

Model/Modelo/Modèle

T3561LF-WL

Series/Series/Seria

Compel

TWO HANDLE WALL MOUNTED LAVATORY

FAUCET TRIM

LLAVES DE AGUA - GRIFOS - DE DOS MANIJAS

PARA INSTALACIÓN EN LA PARED

ROBINETS MURAUX À DEUX MANETTES POUR

LAVABO

Write purchased model number here.

Escriba aquí el número del modelo comprado.

Inscrivez le numéro de modèle ici.

You may need / Usted puede necesitar / Articles dont vous pouvez avoir besoin:

For easy installation of your Delta faucet

you will need:

・

READ ALL

the instructions completely before

beginning.

・

READ ALL

warnings, care and maintenance

information.

・

To complete the deck and valve rough-in prior to

installing this trim kit.

Para instalación fácil de su llave Delta

usted necesitará:

・

LEER TODAS

las instrucciones completamente

antes de empezar.

・

LEER TODAS

los avisos, cuidados, e información

de mantenimiento.

・

Para completar el borde y la instalación de válvulas

dentro de las paredes previa a la instalación de la llave

y sus accesorios.

Pour installer votre robinet Delta

facilement, vous devez:

・

LIRE TOUTES

les instructions avant de débuter.

・

LIRE TOUE LES

les avertissements ainsi que toutes

les instructions de nettoyage et d’entretien.

・

Installez le corps du robinet et terminez le pourtour du

bain avant de poser les accessories de nition.

www.deltafaucet.com 7/08/2015 Rev. B

85756

Rough-in R3500-WL required for installation

Rough-in R3500-WL necesario para la instalación

Rough-in R3500-WL requis pour l'installation

1/8" (3.17mm)

3/32" (2.38mm)

Summary of content (6 pages)

PAGE 1
85756 TWO HANDLE WALL MOUNTED LAVATORY FAUCET TRIM LLAVES DE AGUA - GRIFOS - DE DOS MANIJAS PARA INSTALACIÓN EN LA PARED Model/Modelo/Modèle T3561LF-WL Series/Series/Seria ® Compel ROBINETS MURAUX À DEUX MANETTES POUR LAVABO Write purchased model number here. Escriba aquí el número del modelo comprado. Inscrivez le numéro de modèle ici.
PAGE 2
CLEANING AND CARE Care should be given to the cleaning of this product. Although its finish is extremely durable, it can be damaged by harsh abrasives or polish. To clean, simply wipe gently with a damp cloth and blot dry with a soft towel.
PAGE 3
RP79433▲ Spout Flange and Gasket Reborde del Surtidor y Empaque Embase de bec et joint RP79432 Spout Tube & O-Rings Caño a Tube y Anillo “O”s Bec de Tube et Joint Toriques RP79580 O-Ring Anillo “O” Joint Torique RP70600 O-Rings Anillo “O”s Joint Toriques RP79434▲ Handle Flange and Gasket (2) Reborde de la Manija y Empaque (2) Embase de manette et joint (2) RP79436 Set Screw and Button Tornillo de Ajuste y Botón Vis de Calage et Bouton RP61821 Flange Nut (2) Tuerca con arandela incorporada (2) Écrou à e
PAGE 4
1 9 1 2 8 4 7 6 3 3 5 2 MAINTENANCE – VALVES MAINTENANCE – SPOUT SHUT OFF WATER SUPPLIES BEFORE SERVICING VALVE OR SPOUT ASSEMBLIES If your faucet leaks out of spout or around handle body, replace valve cartridge (1). A. Remove button (2) and set screw (3). Pull off handle (4). B. Remove screw (5) and stem extender (6). C. Remove flange nut (7), flange and gasket (8). D. Remove mounting sleeve (9). E. Unscrew cartridge by turning it counterclockwise using a 19 mm hex socket wrench. F.
PAGE 5
1 A. 2 Figure 1 4 2 1 4 2 1 3 3 B. 1 3 1 2 Figure 2 1 4 2 3 C. 4 1 2 3 2 1 SPOUT FLANGE AND SPOUT INSTALLATION HANDLE FLANGE INSTALLATION A. Pull off plasterguards (1) and discard them. B. Install spout flange (1) and gasket (2). Option: If mounting surface is uneven, apply suitable sealant to the back surface of gasket, according to the manufacturer’s instructions. Finished wall thickness can vary from 1/8" to 1 1/8".
PAGE 6
3 A. 4 1 Finished Wall 1 7/8"-2" (47.6mm-50.8mm) 2 1 B. 3 1 2 5 4 2 3 1 3 7 6 HANDLE INSTALLATION A. Install stem extender (1) onto the cartridge. Mark the stem (1) between 1 7/8" - 2" from finished wall; remove and cut if necessary. Reinstall stem extender (1). Select one of the 4 supplied screw (2) lengths. Screw must securely hold stem extender (1) in place. B. Make sure handle insert (1) and glide ring (2) are pressed into place in the handle (3). Install handle (3) onto stem (4).