Installation Guide

43
1
2
4
3
5
Maintenance
Mantenimiento
Entretien
44
6
If faucet exhibits very low flow –
Unscrew hose from spray head and clean debris
from screen (1) (the screen is located just inside
the spray) . IMPORTANT: Reinstall screen to the
spray head (failure to reinstall the screen could
damage internal parts).
If faucet leaks from under handle or
from spout outlet – Loosen set screw (2) inside
of handle. Remove handle. Remove bonnet cap
(3) by rotating counterclockwise. Bonnet cap
may be stiff due to O-ring, but should rotate
by hand. Remove bonnet nut (4) by rotating
counterclockwise with a wrench. Remove
cartridge (5) by pulling directly back on stem.
Replace cartridge and reassemble.
WARNING: Failure to securely tighten bonnet
nut with a wrench could result in water
damage.
Note: A small amount of water may run out the
spout or drip for a very short period after the
faucet is shut off. This is a natural occurrence
caused by the long fl exible hose.
Maintenance
Cleaning and Care
Care should be given to the cleaning of this prod-
uct. Although its finish is extremely durable, it can
be damaged by harsh abrasives or polish. To clean,
simply wipe gently with a damp cloth and blot dry
with a soft towel. Glass cleaner can be used on SS
(Stainless) finish to remove fingerprints and main-
tain color match. You can avoid turning the faucet
on and off by closing the handle.
LED Guide
If LED (6) is:
Solid Blue - Solenoid valve is open, water
temperature is less than 80
°F (27°C).
Solid Magenta -
Solenoid valve is open, water
temperature is between 80
°F (27°C) and
110
°F
(43
°C).
Solid Red -
Solenoid valve is open, water
temperature is greater than 110
°F (43°C).
3 red flashes before solenoid opens or closes -
replace batteries.
Solenoid Troubleshooting
Note: Normal operation of the faucet will turn
off water fl ow if faucet is not touched for 4
minutes.
1. If your spout fl ashes a red light on then off
and then keeps repeating this,
replace the batteries.
If the spout still fl ashes a red light, please
replace solenoid and electronics kit**. (see
manual bypass of electronics section*)
2. If your spout displays the proper light, but no
water is coming out of the spout,
a. Verify the handle is in the “on” position.
b. Verify the water supplies are turned to the
“on” position.
c. Move handle to the “off” position. Unscrew
hose from spray head and check for any
debris in the spray head inlet. Move handle
to the “on” position to verify water is reaching
the sprayer. Replace spray head.
d. Move handle to the “off” position. Remove
the hose from the solenoid and place bucket
underneath solenoid. Move handle to the “on”
position to check for fl ow coming from the
solenoid. Reconnect hose to solenoid.
e. With handle in the “off” position, remove the
hose from the faucet to the solenoid and place
bucket underneath the solenoid. Move handle
to the “on” position to check if water is going
through the manual valve and reaching the
solenoid. If water is getting to the solenoid, but
it is not getting through the solenoid, replace
solenoid and electronics kit**.
3. If your LED base indicator (6) is not
displaying any lights,
a. Check to make sure the spout connector is
attached to the spout and the wire from the
solenoid / electronics kit. If it is disconnected,
or loose (see step 5), reattach and check for
proper operation.
b. Replace batteries.
c. If it is attached and the light (6) still does not
display on the indicator at the base of the
faucet, contact customer service:
1-800-345-DELTA (3358)
[e-mail] **.
*For immediate and temporary operation of
your faucet.
** Refer to part diagram included in this document
for correct RP number.