User Guide

11
“Enable?” if the function has been disabled);o
4. Press the
button to disable (or enable) energy
saving mode;
5. Then press the MENU/ESC button to exit the menu.
When the function is enabled, if the machine is not used for
about 1 minute, “Energy Saving” is displayed.
Please note!
When in energy saving mode, a few seconds may elapse before
the rst drink with milk is delivered as the appliance must heat
up again.
Cup warmer
This function enables or disables the cup warmer.
Proceed as follows:
1. Press the MENU/ESC button to enter the menu;
2. Press the HOT MILK or LATTE button (g. 8) until “Cup
warmer” appears on the display;
3. Press the
button. “Disable?” is displayed (or
“Enable?” if the function has been disabled);
4. Press the
button to disable (or enable) the
function.
5. Press the MENU/ESC button to exit the menu.
Warming the cups keeps the coee hot.
Setting water hardness
For instructions on setting water hardness, see page 17.
Setting the language
To change the language for the display, proceed as follows:
1. Press the MENU/ESC button to enter the menu;
2. Press the HOT MILK or LATTE button (g. 8) until “Set
language” is displayed;
3. Press the
button;
4. Press the HOT MILK or LATTE button until the required
language is displayed;
5. Press the
button to conrm;
6. Press the MENU/ESC button to exit the menu.
Install lter
For instructions on how to install the lter, see the section
“Installing the lter” on page 18.
Replacing the lter
For instructions on how to replace the lter, see the section
“Replacing the lter” on page 19.
Beep
This enables or disables the beep emitted by the machine
each time the buttons are pressed or an accessory is inserted/
removed. The beep is enabled by default.
To disable or re-enable the beep, proceed as follows:
1. Press the MENU/ESC button to enter the menu;
2. Press the HOT MILK or LATTE button (g. 8) until “Beep”
is displayed;
3. Press the
button. “ Disable?” or “ Enable?” is
displayed;
4. Press the
button to enable or disable the beep;
5. Press the MENU/ESC button to exit the menu.
Cup lighting
This function enables or disables the cup lighting. The lighting
is enabled by default.
The lights come on each time coee and drinks with milk are
made and during each rinse cycle.
To disable or re-enable this function, proceed as follows:
1. Press the MENU/ESC button to enter the menu;
2. Press the HOT MILK or LATTE button (g. 8) until “Cup
lighting” is displayed.
3. Press the
button. “ Disable?” or “ Enable?” is
displayed;
4. Press the
button to enable or disable the cup
lighting;
5. Press the MENU/ESC button to exit the menu.
Default values (reset)
This resets all menu settings and programmed quantities back
to the default values (with the exception of the language which
remains as previously set).
To reset the default values, proceed as follows:
1. Press the MENU/ESC button to enter the menu;
2. Press the HOT MILK or LATTE button (g. 8) until “Default
values” is displayed;
3. Press the ;
button
4. The message “Conrm?” is displayed.
5. Press the
button to conrm and exit.
Statistics function
This displays statistics relating to the machine.
To display, proceed as follows:
1. Press the MENU/ESC button to enter the menu;
2. Press the HOT MILK or LATTE button (g. 8) until
“Statistics” is displayed;
3. Press the
button;
4. Press the HOT MILK or LATTE button (g. 8) to verify:
- how many coees have been made;
- how many times the machine has been descaled;
- the total number of litres of water delivered;
- the total number of drinks made with milk;
- how many times the water lter has been replaced.
5. Press the MENU/ESC button twice to exit the menu.