Setup Guide

ManualsBrandsDell ManualsConverged InfrastructureWyse 5030 Zero Client (VMWare) / P25

Initial Environment Setup

The Dell Wyse P25 zero client is for use with PC-over-IP (PCoIP) protocol

environments. The zero client connects to a host server which is PCoIP

capable.

Before setting up and using the zero client, you must have a properly installed

PCoIP environment that it can access. This guide will help you to set up the

zero client and establish a remote connection to your host server using PCoIP

technology, enabling you to use applications and desktop peripherals as if

you were using them locally.

NOTE: PCoIP technology is designed to deliver a user desktop from a

centralized host server across standard IP networks – including full DVI dual

monitor video, complete USB 2.0 compatibility, and full-duplex

high-definition audio.

Setting Up Your Zero Client

Be sure you have read all safety guidelines before setting up and operating

this product. Refer to the figures and proceed as follows:

1 Make sure the monitor and the zero client are turned off and

disconnected from AC power. Place the zero client on a desk or use

the horizontal stand/bracket for VESA mounting (assemble with the

920275-03L screw kit; insert the thin client with cables facing down or

to the side, but never facing up).

2 Make all desired connections. The monitor, keyboard with mouse, and

Ethernet network are required. Additional connections of peripheral

devices may be made at this time.

3 Connect the power adapter to the zero client power input before

connecting to a 100-240V AC, 50-60 Hz electrical outlet.

4 Press zero client Multifunction power button to apply power. The

power button will light blue; wait for the monitor to display the On

Screen Display (OSD).

LED indicators* include:

* For detailed LED indicators information, go to the Dell Wyse Knowledge

Base at www.dell.com/wyse/knowledgebase and search for

solution 22671.

NOTE: If the monitor does not show the OSD, check all connectors and make

sure the monitor and zero client are turned on.

NOTE: For more information refer to the user and administrators guides, or

contact your Dell support.

Additional Notes

Monitor Types: In addition to DVI and DisplayPort monitors, the zero client is

compatible with analog VGA and digital HDMI monitors. See www.dell.com

for information about approved adapters for connecting VGA and HDMI

monitors to the zero client.

Note: Audio for HDMI is not supported.

IP Address: The zero client is set to DHCP client mode by default. Normally,

the IP address of the zero client and host server are assigned by the DHCP

server on your IP network. If your IP network does not have a DHCP server,

the zero client and host server will fall back to a static IP address mode after a

time-out period of approximately 2 minutes. In the fall back static IP address

mode, you can access the zero client to disable DHCP client mode and assign

a static IP address. The zero client fall back IP address is 192.168.1.101.

Multifunction Power Button/LED:

• Press the button and light turns on: Turns on the zero client.

• Press and hold the button until light turns off: Turns off the zero client.

• Press the button when zero client is connected in a session:

Disconnects zero client from the host server.

Configure

The zero client can be configured to use DHCP or Static IP addressing. To

change the settings, in the On Screen Display go to Options > Configuration

> Network tab. You may need to unlock the settings page with a password

(default password is Administrator).

Establishing a PCoIP Connection

1 Turn on the zero client and click Connect.

2 Enter the IP address of your connection broker if not configured by

your IT administrator.

NOTE: If the Connect button on the zero client user screen is inactive (grayed

out=inactive) or if the zero client cannot discover host servers on the

network, check the network connection and make sure the Ethernet switch or

router is turned on.

3 Enter your user name and password (both are case sensitive). Once

authenticated, a list of hosts you are authorized to connect to will

appear.

4 Select the host to which you want to connect and click OK.

After a successful PCoIP connection, the Status LED of the zero client

will light green. You are now connected.

NOTE: For more details, see About the OSD in the Administrators Guide:

PCoIP Release 4.0.x.

Safety Guidelines

Improper connection, mounting, or use of this product could result in

component failure or undesired interference. Read the following guidelines

before setting up and operating your device.

Setup

• Do not connect to AC power until all other connections (including the

power adapter) are made. Connecting or disconnecting components

or equipment on the back panel when the device is receiving AC

power can cause power surges and damage the device.

• Do not force a connector into its socket. If any undue resistance is

encountered, ensure that the connector is correctly oriented to the

receptacle.

Venting and Care

• Mount the device only as shown or in accordance with the instructions

provided with Dell Wyse-approved mounting accessory kits. Improper

orientation could restrict the airflow of heat from the device and

damage it.

• Allow sufficient space around the device for ventilation; do not place

the device in any enclosure that restricts airflow around the device; do

not place any objects on the device or block the vent outlets. For

environmental operating specifications, locate your product and

download the Fact Sheet using the Cloud clients tab at:

www.dell.com/wyse/P25

Power Sources

• For regulatory compliance use only the power adapter that comes

with your device or a Dell Wyse-approved equivalent. For proper

replacement compare the labels on both device and power adapter to

ensure that their voltages match.

WARNING: Use of any other power adapter may damage your

device or the power adapter. The damage caused by an improper

power adapter is not covered by warranty.

• When turning off the device, make sure to perform a complete

shutdown (via the power button). Do not disconnect the AC power

cord, DC power cord, or shut off power at a circuit breaker (including

power strips), etc., to turn off the device.

• Surge protectors for electrical devices are recommended in areas of

lightning. However, when lightning is occurring, your equipment

should be properly shut down and unplugged from AC power until the

storm has passed.

Need more information?

Dell Reference Guides - Documentation is available at:

www.dell.com/wyse/manuals

Dell Approved Mounting Accessory Kits - Information about approved

mounting accessory kit options is available at:

www.dell.com/wyse/accessories

Dell Support - Upgrade software images for installation are available at:

www.dell.com/wyse/downloads

Dell Device Manager - Information about Wyse remote management

software is available at: www.dell.com/wyse/WDM

DEll and the Environment - Information about Dell compliance with RoHS

and with the Waste Electrical and Electronic Equipment (WEEE) is available at:

www.dell.com/environment

Dell and Recycling - Information about recycling unwanted Dell product

within the United States is available at: www.dell.com/recycling

Dell Warranty - The standard warranty is three years from the date of

purchase.

__________________________________________________________________

This product is protected by U.S. and international copyright and intellectual

property laws. Dell and the Dell logo are trademarks of Dell Inc. in the United

States and/or other jurisdictions. All other marks and names mentioned

herein may be trademarks of their respective companies.

Sept 2014 Dell PN: JW46G Rev: A00

Status LED Bi-color light for connected / not connected

(green/amber)

Power LED Single light for power on/off (blue)