Dell Networking W-7024 Controller Installation Guide
Copyright Information © 2015 Aruba Networks, Inc. Aruba Networks trademarks include , Aruba Networks®, Aruba ® Wireless Networks , the registered Aruba the Mobile Edge Company logo, and Aruba Mobility Management System®. Dell™, the DELL™ logo, and PowerConnect™ are trademarks of Dell Inc. All rights reserved. Specifications in this manual are subject to change without notice. Originated in the USA. All other trademarks are the property of their respective owners.
Contents Contents 3 Preface 7 Guide Overview 7 Related Documentation 7 Contacting Dell 7 W-7024 Controller 8 Packaging Checklist 8 W-7024 Components 9 Access Ports Access Port LEDs Uplink Ports 10 10 11 Uplink Port LEDs 11 SFP/SFP+ Modules and DAC Cables 12 Management Port 13 Power, Status, and Peered LEDs 13 LCD Panel 14 LCD Mode Menu 14 Disabling the LCD Screen 15 USB Interface 16 Serial Console Port 16 Serial Console Port Adaptor 16 Micro-USB Console Port 17 Micro
Precautions 18 Selecting a Location 19 Rack Mounting - Standard/Front 19 Required Tools and Equipment 19 Installation Steps 20 Rack Mount Installation- Mid Required Tools and Equipment 21 Installation Steps 21 Table or Shelf Installation 22 Required Tools and Equipment 22 Installation Steps 22 Wall Mounting 22 Required Tools and Equipment 23 Installation Steps 23 Connecting and Disconnecting the AC Power Cord 24 Connecting the AC Power Cord 24 Disconnecting the AC Power Cord 2
Canada 29 Japan VCCI 29 Taiwan (BSMI) 29 Europe 29 South Korea 29 EU Regulatory Conformance 30 Battery Statements 30 Proper Disposal of Dell Equipment 30 Waste of Electrical and Electronic Equipment 30 European Union RoHS 30 India RoHS 30 China RoHS 31 Dell Networking W-7024 Controller | Installation Guide Contents | 5
Preface This document describes the hardware features of the Dell Networking W-7024 Controller. It provides a detailed overview of the physical and performance characteristics of the controller and explains how to install the controller and its accessories. Guide Overview l W-7024 Controller on page 8 provides a detailed hardware overview of the W-7024 controller and its components. l Installation on page 18 describes how to install the W-7024 controller and its components.
Chapter 1 W-7024 Controller The W-7024 Controller is a wireless LAN controller that connects, controls, and intelligently integrates wireless Access Points (APs) and Air Monitors (AMs) into a wired LAN system. There are two models of the W-7024 controller that do not differ physically or functionally from each other.
Table 3: Package Contents Item Quantity Power Cable 1 Micro-USB Cable 1 Rubber Feet 4 Installation Guide (this document, printed) 1 Quick Start Guide (printed) 1 Dell Safety, Environment, and Regulatory Information (printed) 1 Dell Warranty and Support Information (printed) 1 Dell Software License Agreement (printed) 1 NOTE: Optional accessories are available for use with the W-7024 controller and are sold separately. Contact your Dell sales representative for details and assistance.
The following table lists the different components of the W-7024 controller: Table 4: W-7024 Controller Components Component Description Page Access ports 24 x 10/100/1000BASE-T PoE/PoE+ Ethernet ports 10 Uplink ports 2 x 10GBASE-X ports 11 Management port Allows connection to a separate management network 13 Power, Status, and Peered LED Provides basic monitoring of the controller 13 LCD Allows configuration of LCD behavior and other basic operations 14 Enter button Allows execution of
l LINK/ACT— Placed on the left side of the port, this LED displays the link status and activity of the port. l STATUS— Placed on the right side of the port, this LED displays the status of the port. The information displayed by this LED changes based on the LCD mode. The LED behavior corresponding to each LCD mode is listed in Table 5.
l STATUS— Placed on the top right of the port, this LED displays the status of the port. The information displayed by this LED changes based on the LCD mode. The LED behavior corresponding to each LCD mode is listed in Table 6.
Table 8: Supported SFP/SFP+ Modules SFP/SFP+ Description SFP-SX SFP, 1000BASE-SX, LC Connector; 850nm pluggable GbE optic; up to 300 meters over multi-mode fiber (Type OM2). SFP-LX SFP, 1000BASE-LX, LC Connector; 310nm pluggable GbE optic; up to 10,000 meters over single-mode fiber. SFP-TX SFP, 1000BASE-T SFP; copper GbE pluggable; RJ45 connector; up to 100 meters over Category-5, 5e, 6 and 6a unshielded twisted pair cable.
Table 10: Power, Status, and Peered LEDs LED Function Indicator Status Power System Power Green (Solid) Power On Off Power Off Green (Solid) Operational Green (Blinking) Device is loading software Amber (Blinking) Major alarm Amber (Solid) Critical alarm Off No power NA NA Status Peered System Status Reserved for future use LCD Panel The W-7024 controller is equipped with an LCD panel that displays information about the controller’s status, and provides a menu that allows basic ope
Table 11: LCD Panel Mode LCD Mode Function Displayed Status/ Command Description Status Displays the ArubaOS version.
USB Interface The W-7024 controller is equipped with a USB 2.0 interface on the back panel of the controller. A USB storage device can be used to save and upload configurations to the controller. USB functions are controlled through the LCD panel on the front of the controller. For more information on the LCD panel and its functions, see "LCD Panel" on page 14. Serial Console Port For direct local management of the controller, use the serial console port located on the back panel of the controller.
Figure 6: RJ-45 (Female) to DB9 (Male) Modular Adapter Conversion RJ-45 Female Pin-Out 1 2 3 TxD 4 5 GND 6 RxD 7 8 Internal Connections RJ-45 TxD 3 4 5 GND RxD 6 DB-9 Male Pin-Out DB-9 2 5 3 9 8 7 6 5 4 3 2 1 Ground RxD TxD Micro-USB Console Port The W-7024 controller is equipped with one Micro-USB (type B) connector on the back panel of the controller that provides console access for direct local access.
Chapter 2 Installation This chapter describes how to install a W-7024 controller using the different mounting options available. The W7024 controller ships with equipment needed to mount the controller in a standard two-post 19-inch Telco rack. CAUTION: Only use the included or Dell specified cables, power cords, AC power supplies, and batteries. The power cord should not be used with other electric equipment than what is specified by Dell.
Selecting a Location The W-7024 controller, like other networking and computing devices, requires the following “electronic-friendly” environment: l Reliable power n l l l Verify that the electrical outlet is compatible with the W-7024 controller power supply. Cool, non-condensing ventilation n For proper operation, the W-7024 controller requires an environment with an ambient air temperature between 0º C and 40º C (32º F and 104º F).
Installation Steps To install a W-7024 controller from the front in a standard two-post 19-inch Telco rack: 1. Place the mounting brackets over the mounting holes on either side of the controller towards the front (see Figure 7). Figure 7: Rack Mounting Brackets 2. Secure the brackets to the controller using the eight screws for the mounting bracket (four per bracket) and a suitable screwdriver. 3.
ATTENTION: Chaque contrôleur W-7024 doit disposer de son propre équipement de montage. Veillez à ne placer aucun autre équipement réseau directement sur un contrôleur W-7024 installé. Dans le cas contraire, vous risqueriez d’endommager le périphérique.
Figure 10: Mid-Mount Rack Installation NOTE: Leave a minimum of 10 cm (4 inches) of space on the left and right side of the controller for proper air flow and ventilation. Leave additional space in the front and the back of the controller to access network cables, LED status indicators, and power cord. Table or Shelf Installation Required Tools and Equipment l Rubber feet Installation Steps 1. Attach the rubber feet to the bottom of the controller (see Figure 11). 2.
Required Tools and Equipment The following tools and equipment are required for installing a W-7024 controller on a wall: l Wall-mount brackets (x2) (included in the mounting accessory kit) l Screws for the wall mounting bracket (x8): M4 x 8 mm Phillips Flat Head Screws l Wall anchors: Optional (not included in the package) l Wall-mount screws (not included in the package, the type of screw depends on the installation surface) l Suitable screwdrivers for all screw types (not included in the package
Figure 13: Wall-Mount Installation Connecting and Disconnecting the AC Power Cord Once the controller is installed, it is ready to be powered on. The W-7024 controller is not equipped with an On/Off switch. The controller will power on when the AC power cord is connected to the AC power connector and an AC power outlet. Connecting the AC Power Cord To connect the AC power cord to the W-7024 controller: 1. Lift the power cord retaining clip so that it is not blocking the AC power connector. 2.
Disconnecting the AC Power Cord To disconnect the AC power cord from the W-7024 controller: 1. Lift the power cord retaining clip off the AC power cord. 2. Pull the AC power cord from the AC connector. 3. The W-7024 controller is now turned Off. Installing an SFP/SFP+ Module NOTE: Use standard ESD precautions when installing or removing an SFP/SFP+ module. To install an SFP/SFP+ module into the W-7024 controller: 1.
Figure 15: Connecting an LC Fiber Optic Cable Disconnecting an LC Fiber Optic Cable To disconnect an LC fiber optic cable from an SFP-SX or SFP-LX module, depress the transceiver handle to release the latch on the cable and simultaneously pull the cable out of the port.
Chapter 3 Specifications, Safety, and Compliance W-7024 Specifications Physical l Device Dimensions (without mounting brackets) (HxWxD): 1.72” x 17.40” x 12.32” (4.37 cm x 44.2 cm x 31.3 cm) l Device Weight: 11.303 lbs (5.127 kgs) Power Supply Specifications l 580 W Integrated Power Supply n AC Input Voltage: 115 VAC to 230 VAC n AC Input Current: 6.
CLASS 1 LASER PRODUCT CAUTION: Use of controls or adjustments of performance or procedures other than those specified in this manual may result in hazardous radiation exposure. ATTENTION: L’utilisation de commandes ou de réglages de performances ou de procédures qui ne sont pas spécifiées dans ce manuel risque d’entraîner une exposition à des rayonnements dangereux. This product complies with 21 CFR Chapter 1, Subchapter J, Part 1040.10, and IEC 60825-1: 1993, A1: 1997, A2: 2001, IEC 60825-2: 2004+A1.
This product complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
EU Regulatory Conformance This product is CE marked according to the provisions of the EMC Directive (2004/108/EC) - CE. Dell, hereby declares that W-7024 controller device models are in compliance with the essential requirements and other relevant provisions of Directive (2004/108/EC) – CE. The Declaration of Conformity made under Directive 1999/5/EC is available for viewing on dell.com. Battery Statements CAUTION: The battery supplied with this product may contain perchlorate material.
China RoHS Dell products also comply with China environmental declaration requirements and are labeled with the “EFUP 50” label shown at the left.
| Specifications, Safety, and Compliance Dell Networking W-7024 Controller | Installation Guide
