Dell PowerVault TL2000 Tape Library and TL4000 Tape Library User's Guide
Dell PowerVault TL2000 Tape Library and TL4000 Tape Library User's Guide
Information in this document is subject to change without notice. (c) 2014 Dell Inc. All rights reserved. Reproduction in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden. Trademarks used in this text: Dell, the DELL logo and PowerVault are trademarks of Dell Inc. Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Dell Inc.
Read this first Minimum firmware levels for common library features Table 1. Minimum firmware levels for common library features Feature Minimum Firmware Level(s) Required LTO HH V2 Tape Drives Library firmware level must be at A.00, or greater, to support HH V2 Tape Drives. LTO 6 Tape Drive Library firmware must be at B.50 or greater to support the Ultrium 6 drives. Ensure the minimum version required to support Ultrium 6 tape drives are installed on the host.
Dell provides online and telephone-based support and service options. Service availability varies by country and product, and some services might not be available in your area. To contact Dell for sales, technical support, or customer service issues follow the steps that are listed: 1. Visit http://support.dell.com. 2. Verify your country or region in the Choose A Country/Region menu at the bottom of the page. 3. Click Contact Us on the left side of the page. 4.
Contents Read this first . . . . . . . . . . . . iii Minimum firmware levels for common library features . . . . . . . . . . . . . . Contacting Dell . . . . . . . . . . . . . . iii . iii Figures . . . . . . . . . . . . . . vii Tables . . . . . . . . . . . . . . . xi Safety and environmental notices . . . xiii Danger and caution notices . . Laser Safety and Compliance . Performing the safety inspection Rack safety . . . . . . . . . . . . . . xiii . . . . . . . xiv procedure . . . xiv . . . . . . .
Chapter 6. Using Ultrium Media . . . . 6-1 Data Cartridges . . . . . . . . . . . . . 6-1 Cartridge Compatibility . . . . . . . . . 6-3 WORM (Write Once, Read Many) Cartridges . . . 6-3 WORM Media . . . . . . . . . . . . 6-3 Data Security on WORM Media . . . . . . 6-3 WORM Media Errors . . . . . . . . . . 6-4 Cleaning Cartridge. . . . . . . . . . . . 6-4 Bar Code Label . . . . . . . . . . . . . 6-4 Guidelines for Using Bar Code Labels . . . . 6-6 Write-Protect Switch . . . . . . . . . . .
Figures 1-1. 1-2. 1-3. 1-4. 1-5. 1-6. 1-7. 2-1. 2-2. 2-3. 2-4. 2-5. 2-6. 3-1. 3-2. 3-3. 3-4. 3-5. 4-1. 4-2. 4-3. 4-4. 4-5. 4-6. 4-7. 4-8. 4-9. 4-10. 4-11. 4-12. 4-13. 4-14. 4-15. 4-16. 4-17. 4-18. Front panel of a 2U library . . . . . . 1-1 Front panel of a 4U library . . . . . . 1-2 Rear panel (drive sled only) of a half height Fibre Channel drive . . . . . . . . . 1-3 Rear panel of a 4U library with full height Fibre Channel drive and half height SAS drives . . . . . . . . . . . . .
5-14. 5-15. 5-16. 5-17. 5-18. 5-20 5-23 5-24 5-25 5-58. 5-26 5-27 5-29 5-29 5-30 5-30 5-31 5-32 5-60. 6-1. 6-2. 6-3. Service Library: Perform Key Path Diagnostics page . . . . . . . . . 5-63 The Service Library: Upgrade Firmware page, showing one Ultrium 3 SAS Half Height V2 drive and one Ultrium 4 SAS Half Height drive. . . . . . . . . . 5-65 Service Library: Reboot page . . . . . 5-65 The LTO Ultrium Data Cartridge . . . .
10-20. Library front panel LEDs . . . . . . 10-21. Access hole for the left magazine (facing rear of library) . . . . . . . . . . 10-22. Access hole for the right magazine (facing rear of library) . . . . . . . . . . 10-23. Left magazines pulled out of a 4U library (facing front of library) . . . . . . . 10-24. Mounting brackets and anchors for securing the library in a rack (one bracket and anchor on each side of the library). . 10-22 10-23 10-24 10-25 10-25. Front view of rack showing screw placement .
x Dell PowerVault TL2000 Tape Library and TL4000 Tape Library User's Guide
Tables 1. 1-1. 1-2. 1-3. 1-4. 1-5. 1-6. 1-7. 1-8. 1-9. 1-10. 1-11. 3-1. 3-2. 3-3. 4-1. 5-1. 5-2. 5-3. 5-4. 5-5. 5-6. 5-7. 5-8. 5-9. 5-10. 5-11. 5-12. 6-1. Minimum firmware levels for common library features . . . . . . . . . . . iii 2U library and 4U library front panel descriptions . . . . . . . . . . . 1-2 2U library and 4U library rear panel descriptions . . . . . . . . . . . 1-4 Tape drive model and host interface type 1-8 Library storage capacity and data transfer rate . . . . . . . . . . . . . .
xii Dell PowerVault TL2000 Tape Library and TL4000 Tape Library User's Guide
Safety and environmental notices When this product is used, observe the danger, caution, and attention notices that are contained in this guide. The notices are accompanied by symbols that represent the severity of the safety condition. The sections that follow define each type of safety notice and give examples. Danger and caution notices Danger Notice A danger notice calls attention to a situation that is potentially lethal or extremely hazardous to people.
If the symbol is... It means... A hazardous condition due to the unit's susceptibility to electrostatic discharge. Laser Safety and Compliance Before the library is used, review the following laser safety information. Class I Laser Product The product might contain a laser assembly that complies with the performance standards set by the US Food and Drug Administration for a Class I laser product. Class I laser products do not emit hazardous laser radiation.
Rack safety The following general safety information must be used for all rack mounted devices. DANGER v Always lower the leveling pads on the rack cabinet. v Always install stabilizer brackets on the rack cabinet. v To avoid hazardous conditions because of uneven mechanical loading, always install the heaviest devices in the bottom of the rack cabinet. Always install servers and optional devices, starting from the bottom of the rack cabinet.
CAUTION: Removing components from the upper positions in the rack cabinet improves rack stability during relocation. Follow these general guidelines whenever you relocate a populated rack cabinet within a room or building: v Reduce the weight of the rack cabinet by removing equipment, starting at the top of the rack cabinet. When possible, restore the rack cabinet to the configuration of the rack cabinet as you received it.
Preface This manual contains information and instructions necessary for the installation, operation, and service of the Dell™ PowerVault™ TL2000 Tape Library and TL4000 Tape Library. Related Publications Refer to the following publications for additional information. v Dell™ PowerVault™ TL2000 Tape Library and TL4000 Tape Library Getting Started Guide provides installation information.
xviii Dell PowerVault TL2000 Tape Library and TL4000 Tape Library User's Guide
Chapter 1. Product Description The Dell™ PowerVault™ TL2000 Tape Library (2U library) and the Dell PowerVault TL4000 Tape Library (4U library) provide compact, high-capacity, low-cost solutions for simple, unattended data backup. The 4U library houses up to 48 tape cartridges (or 45 and an elective 3-slot I/O Station) in a compact 4U form factor with easy access to cartridges via four removable magazines.
1 8 6 3 2 7 4 5 a77ug240 3 Figure 1-2. Front panel of a 4U library Table 1-1 below contains front panel descriptions for both the 2U library in Figure 1-1 on page 1-1 and the 4U library in Figure 1-2. Table 1-1. 2U library and 4U library front panel descriptions Number Item Description 1 Power button Pressing this button powers ON the library. Pressing and holding this button for 4 seconds will power OFF the unit (soft power down).
Table 1-1. 2U library and 4U library front panel descriptions (continued) Number Item 5 Control keys Description v UP (∧) - The upper left button is used to scroll upward through menu items. v DOWN (∨) - The lower left button is used to scroll downward through menu items. v CANCEL (X) - The upper right button is used to cancel a user action and return to the previous menu screen. v SELECT (') - The lower right button is used to display a sub-menu or force an accessor action.
2 11 3 10 4 9 8 7 6 5 a77ug135 1 Figure 1-5. Rear panel of a 2U library with a full height dual port SAS drive Table 1-2. 2U library and 4U library rear panel descriptions Number Item 1 Power connector(s) Description Both libraries require a 110/220 volt AC power connection. v The 2U library has one power supply. v The 4U library has a minimum of one power supply, but has the capability of adding a redundant power supply.
Table 1-2. 2U library and 4U library rear panel descriptions (continued) Number Item Description 8 Ethernet port This port is used to connect the library to a network.
CAUTION: The library must be offline from any user and all media must be removed from the drives before license keys are installed or any configuration modifications are made. Please refer to “Power ON/OFF” on page 2-4 and “Removing Cartridges from Magazine Slots” on page 9-1 for instructions to take the library offline and to eject media from the drives. To prevent possible data loss due to a key management server failure, Dell recommends the use of a primary and secondary key management server.
Supported Internet Protocols The library supports the following Internet protocols: v IPv4 v IPv6 To learn more about Internet protocols, visit http://www.iana.org/. SNMP Messaging Occasionally, the library may encounter a situation that you want to know about, such as an open magazine or a fault that causes the library to stop.
Maximum Library Storage Capacity and Data Transfer Rate Maximum library storage capacity and maximum data transfer rates are as follows: Table 1-3.
Table 1-4. Library storage capacity and data transfer rate (continued) Characteristic 2U Library Specification Sustained native data transfer rate 4U Library Specification LTO 3 HH: 60 MBs, LTO 3 HH V2: 80 MBs LTO 3 FH: 80 MBs LTO 4 HH and FH: 120 MBs LTO 5 : 140 MBs LTO 6: 160 MBs Ultrium Tape Drives This library supports the Ultrium 3, 4, 5, and 6 Tape Drives. Each tape drive in the library is packaged in a container called a drive sled.
a77ug008 Figure 1-6. Library drive sled without ESD springs (SCSI sled shown) a77ug202 1 Figure 1-7. Library drive sled with ESD springs [1] (SAS sled shown) Speed Matching To improve system performance, the Ultrium 3, Ultrium 4, Ultrium 5, and Ultrium 6 Tape Drives use a technique called speed matching to dynamically adjust its native (uncompressed) data rate to the slower data rate of the attached server.
Power Management The Ultrium 3, Ultrium 4, Ultrium 5, and Ultrium 6 Tape Drive's power management function controls the drive's electronics so that part of the electronics completely turn OFF when circuit functions are not needed for the drive's operation. Media The library uses Ultrium Tape Cartridges that provide up to 2500 GB native capacity (up to 6250 GB with 2.
Library Specifications Physical Specifications Table 1-5. Physical Specifications Specification 2U library 4U library Height Rack mount 87.6 mm (3.44 in), stand-alone 97.6 mm (3.84 in) Rack mount 175.2 mm (6.9 in), stand-alone 185.2 mm (7.3 in) Width 447.5 mm (17.6 in.) 447.5 mm (17.6 in.) Depth Rack mount 740 mm (29.13 in), stand-alone 810 mm (31.9 in) Rack mount 740 mm (29.13 in), stand-alone 810 mm (31.9 in) Weight with 1 drive and without media 15.59 kg (34.37 lbs.) 21.32 kg (47 lbs.
Table 1-8. Operation Specifications: Ultrium 5 (continued) Library with Ultrium 5 drive(s) 2U Library 4U Library Ultrium 5 Full Height Drive: Fibre Channel, SAS Ultrium 5 Half Height Drive: Fibre Channel, SAS Drive types 8 Gb/s Fibre Channel 6 Gb/s SAS Interfaces *Host Interface Drive Transfer Rates may vary depending on host usage and interface utilization. Table 1-9.
Environmental Specifications Table 1-11. Environmental Specifications Temperature Operating 10° to 35° C (50° to 95° F) Storage, without cartridges -30° to 60° C (-22° to 140° F) Wet bulb, operating 26° C (79.0° F) maximum Temperature shock immunity - maximum rate of change 10° C (18° F) per hour Miscellaneous Dust concentration less than 200 microgram/cubic meter Maximum acoustical noise sound power levels LwAd in bels 6.6/6.
Chapter 2. User Interfaces This library has two user interfaces. v Operator Control Panel - located on the front panel of the library v “Web User Interface” on page 2-4 - accessed via a web browser Operator Control Panel The Operator Control Panel operates in two basic modes. v User Interaction mode - This mode is employed when a user is pushing buttons on the Operator Control Panel. v System Driven mode - This is the normal mode of operation.
become illuminated. The error code remains on the Operator Control Panel until a push button is pressed, which causes the Operator Control Panel to return to the Home Screen. v Numeric error codes are only used for unrecoverable, fatal errors, otherwise text status messages are displayed. Power-ON Display When the library powers ON or resets, it goes through several internally controlled processes that allow it to get initialized and running. These processes are called Power-On-Self-Test (POST).
The following are additional operational details of LEDs: v The Ready/Activity LED is illuminated any time the unit is powered ON and functional. The Ready/Activity LED blinks whenever there is library or drive activity. This LED will also blink when the unit is OFFLINE. v The Clean LED is illuminated when either a cleaning requested or a cleaning required flag has been issued by the drive. The LED is turned off after a successful drive cleaning operation.
2. Using the UP and DOWN buttons, select one of the various predefined values for that item. 3. As soon as the Operator Control Panel display shows the correct value, press the SELECT button to apply the value. Toggling Values Toggle values are used to switch between two different states like ON and OFF. 1. After navigating to the menu item, press the SELECT button to select the menu item. 2. Using the UP and DOWN buttons, select one of the various predefined states for that item. 3.
User Interface, you must first set the IP address using the Operator Control Panel. Refer to "Configure: Network" on page 5-23 or "Configure Library: Network" on page 5-45. Login Important: Some options of the Web User Interface take the library OFFLINE. This inactive mode can interfere with host-based application software, causing data loss. Make sure the library is idle before attempting to perform any remote operations that will take the library OFFLINE.
a77ug070 other IPv6 address). Figure 2-2. Web User Interface login page System Status a77ug080 The System Status screen is always present after login giving current status of the library. a77ug089 Figure 2-3. 2U library System Status screen Figure 2-4. 4U library System Status screen Status icons indicate the following conditions. v The green check mark indicates that the library is fully operational and that no user intervention is required.
v If Auto Clean is enabled and a cleaning cartridge is not present, or if a cleaning cartridge is present, but not in a reserved slot, Auto Clean status will show Chk Media/Rsvd Slot? and Status will show a green check mark and the words Media Attention. The Auto Clean status disappears from the system status screen once Auto Clean has been properly configured. You will get messages if the cleaning media expires. Figure 2-5.
If your library has -05 level redundant power supplies, the "Green" LED will be ON on both power supplies. If both "Green" LEDs are not ON, replace the failed power supply (refer to “Replacing a Power Supply” on page 10-10). Web User Interface Help Pages Each screen on the Web User Interface has an associated Help page. To access a Help page, click on Help in the upper right corner of the screen. A new web page will open. Using the left navigation pane, select the desired Help page.
Chapter 3. Installation Planning Before installing your library, take time to review the following information. Determining the Number of Logical Libraries You can partition the library into as many logical libraries as there are drives in the library. Basic Guidelines v Each logical library must contain at least one drive. v A library configuration of exactly one logical library equals the entire physical library. v The library issues a warning to the user if media is moved across logical libraries.
Using Multiple Logical Libraries for Library Sharing Multiple logical libraries are an effective way for the library to simultaneously back up and restore data from heterogeneous applications.
Library Partitioning and Element Addressing Library 4U systems with firmware versions of .80 and higher, and containing at least 2 drives, have the ability to configure two logical libraries (create two partitions). This partitioning has been expanded with the new library firmware and half-high drive integration. Now it is possible to configure 1, 2, 3 or 4 partitions in the 4U library. Additionally the 2U library can now be configured into one or two partitions.
Configuration of a 1 - Partition System A one partition system configured for a 4U library contains any and all drives present in any drive positions, and it will contain all four magazines. When configured with one logical partition, the Element Address assignments will be as follows: DTE assignments will be as shown in Figure 3-1.
Configuration of a 3 - Partition System A three partition system must have at least three drives installed. A drive must be installed in drive position 1, another drive must be installed in drive position 2, and another drive must be installed in either drive position 3 or drive position 4. Partition 1 will contain the first drive and the first magazine. Partition 2 will contain the second drive and the second magazine. Partition 3 will contain any drives in drive position 3 and drive position 4.
SCSI Element Addressing Every logical library starts at the first drive slot with the current assigned element start address (default value 256). It will be incremented from the bottom to the top slots for every drive slot. There is one exception to this addressing scheme to accommodate libraries currently in the field. A 4U library containing only full height drives will continue to have the addresses assignments 256 and 257, thus causing no interruptions to their operation.
Logical Unit Number (LUN) Scanning The library uses a single SCSI or Loop ID per drive and dual LUNs to control the tape drive (LUN 0) and library accessor (LUN 1). The library requires a Host Bus Adapter (HBA) that supports LUN scanning. If it is not enabled, your host system will not scan beyond LUN 0 and will fail to discover the library. It will only see the tape drive. Important: Some HBAs, such as RAID controllers, do not support LUN scanning.
Note: For maximum performance, it is recommended to have a maximum of one drive per SCSI bus. – Only use the maximum system-to-device cable length of 25 m (82 ft) when attaching directly to one device (a point to point interconnection). Note: Daisy-chaining is NOT recommended due to potential issues with SCSI bus performance, SCSI cables/connectors, and host bus adapters. Physical Characteristics of the SCSI Interface The library operates as a set of SCSI-3 devices.
Note: Daisy-chaining is NOT recommended due to potential issues with SCSI bus performance, SCSI cables/connectors, and host bus adapters. Removal of any jumpers will create a SCSI bus for each drive installed in your library for attachment to multiple servers or to multiple SCSI adapter cards on one server. Remember that each SCSI bus must be terminated. Multiple SCSI buses may be required for maximum performance, depending on the application and data compression ratio.
active/passive cluster failover. LAN-free drive sharing is not supported. Ultrium 3 and Ultrium 4 SAS drive sleds use the SFF-8088 connection at the drive sled end and SFF-8088 or SFF-8470 at the host adapter end. Fibre Channel Interface Fibre Channel allows for an active intelligent interconnection scheme, called a Fabric, to connect devices. Everything between the ports on Fibre Channel is called the Fabric.
Zoning allows you to partition your SAN into logical groupings of devices so that each group is isolated from the other and can only access the devices in its own group. Two types of zoning exist: hardware zoning and software zoning. Hardware zoning is based on physical fabric port number. Software zoning is defined with a World Wide Node Name (WWNN) or World Wide Port Name (WWPN). While zoning can be reconfigured without causing an outage, some zoning configurations can become complicated.
3-12 Dell PowerVault TL2000 Tape Library and TL4000 Tape Library User's Guide
Chapter 4. Installation and Configuration Note: Review the information in "Installation Planning" before installing your library. To install a desktop or rack mounted 2U library or 4U library, perform the procedures in this chapter in the order they are presented. Using the Library Configuration Form Before beginning the installation and configuration of your library, make a copy of the Appendix G, “Library Configuration Form,” on page G-1.
Table 4-1. Location criteria (continued) Criteria Definition Air quality The library should be placed in an area with minimal sources of particulate contamination. Avoid areas near frequently used doors and walkways, stacks of supplies that collect dust, printers, and smoke-filled rooms. Excessive dust and debris can damage tapes and tape drives. Humidity 15-80 % RH non-condensing Clearance v Back: Minimum of 15.4 cm (6 inches) v Front: Minimum of 30.8 cm (12 inches) v Sides: Minimum of 5.
– Bar code labels – Foot pads (for desktop installation) v With every library that contains a SCSI drive: – SCSI terminator (one per SCSI drive) – SCSI library-to-host cable (if ordered by customer) v With every library that contains a Fibre Channel drive: – Fibre Channel library-to-host/switch cable (if ordered by customer) v With every library that contains a SAS drive: – SAS library-to-host cable (if ordered by customer) v Rack Mount Kit Important: If your library did not contain preinstalled drives, the
a77ug085 1 Figure 4-2. Installing foot pads on the bottom of the library enclosure 4. Carefully return the library to an upright position. Important: Do not place any objects on top of the library. Removing and Storing the Shipping Lock Important: The shipping lock, which prevents the library accessor from moving during shipment, must be removed before the library is powered ON. The shipping lock is held in place with a label and is located in the top center of the library.
1 a77ug018 2 a77ug195 Figure 4-3. Shipping lock and label Figure 4-4. Removing the Shipping lock and label 2. Store the lock ( 1 ) and label ( 2 ) on the rear panel of the library as shown in Figure 4-5 on page 4-6. Chapter 4.
1 a77ug019 2 Figure 4-5. Library shipping lock and label storage location on rear panel of library Rackmounting the Library (for Rack Installation ONLY) The 2U library and the 4U library are easily installed into a standard 19-inch rack system. The 2U library requires 2U (3.5 in.) of space. The 4U library requires 4U (7 in.) of space. If you are not rackmounting your library, skip this procedure and go to “Attaching the Library to a Server” on page 4-16. Important: A 2U library weighs 15.59 kg (34.
8 4 2 1 5 7 6 a77ug275 3 Figure 4-6. Rack Kit A mounting hardware a. Rack Kit A: The following parts make up Rack Kit A. v Packaged in cardboard material: – 2 rails (not shown) See Figure 4-9 on page 4-9 for a graphic of the rails.
8 2 1 4 7 6 5 a77ug292 3 Figure 4-7. Rack Kit B mounting hardware b. Rack Kit B: The following parts make up Rack Kit B. v Packaged in plastic material: – 2 rails (not shown) See Figure 4-10 on page 4-10 for a graphic of the rails.
3 2 1 4 2 a77ug133 1 Figure 4-8. Examples of EIA units for round hole and square hole installations 1 Two EIA units for round hole and 2 square hole installation 3 Wide Gaps within the EIA unit 4 Narrow Gaps between EIA units 3. Using the screws for your rack type (round holes or square holes) and a #2 Phillips screwdriver and ensuring that the flange on each rail points toward the other to form a shelf, secure one rail to each side of the rack in your chosen rack location.
a77ug274 Figure 4-10.
a77ug271 a77ug196 Figure 4-11. Kit A (top picture with circles) showing rails installed. Rack Kit B is below showing the front view of this kit installed. Note: The rail must be fastened with the bottom of the rail parallel to floor and at the same level. 4. Using the Torx wrench included in your shipment, remove the screws ( 1 ) as shown in Figure 4-12 on page 4-12. Screw locations on the 4U library are similar. Chapter 4.
a77ug269 1 Figure 4-12. 2U library rack anchors and mounting brackets a77ug270 5. Install the library rack anchors ( 2 ) as shown in Figure 4-12 on each side of your library using the longest counter-sunk screws included in the rack kit. Figure 4-13.
a77ug267 Figure 4-14. 2U library side screws to remove 6. Install the library mounting brackets ( 1 ) as shown on the 2U library on each side of the library using the screw that was removed from your library and an additional short, counter-sunk screw included in the rack kit. (The 4U rack anchors and mounting brackets are similar.) 7. With library rack anchors and mounting brackets installed, slide the library onto the rails (as shown in Figure 4-15 on page 4-14 and Figure 4-16 on page 4-14).
a77ug267 a77ug266 Figure 4-15. Sliding the 2U library into the rack Figure 4-16. Sliding the 4U library into the rack 8.
1 a77ug268 of each mounting bracket and tightening them ( 1 ). Figure 4-17. Securing the 2U library to the rack Chapter 4.
a77ug265 1 Figure 4-18. Securing the 4U library to the rack 9. Install either the round or the square rack hole covers for the 4U library as shown in Figure 4-18. There are 6 covers for each side for a total of 12. Attaching the Library to a Server The 2U library and the 4U library can be attached to servers using the following interfaces: v SCSI (LVD Ultra 160) v Fibre Channel v Serial Attached SCSI (SAS) Connecting the Host Interface Cable To connect the host interface cables to the library: 1.
connector. Unused SAS connectors do not need to be terminated. a77ug017 1 4 2 3 Figure 4-19. Attaching a SCSI host interface cable to the 2U library a77ug101 4 6 3 1 2 5 Figure 4-20. Attaching host interface cables to the 4U library. THE CONFIGURATION SHOWN IN THIS FIGURE IS USED FOR EXAMPLE ONLY. THIS CONFIGURATION IS NOT SUPPORTED. 2 3 a77ug134 1 Figure 4-21. Attaching a SAS interface cable to the 2U library 3.
device on the SCSI bus. Otherwise, attach one end of a SCSI cable to the remaining port and the other end to the next device on the SCSI bus. Make sure that the last device on the SCSI bus is properly terminated. Note: Only cables and terminators specified for Ultra160 or Ultra320 use or labeled as Multi Mode should be used. Note: The host bus adapter should be LVD SCSI. A single-ended (SE) SCSI host bus adapter will work, but will severely degrade performance, and limit cable length.
3. Plug the other end of each power cord into the nearest properly grounded power outlet. Use separate power sources for each power supply for redundant power. Attention: To disconnect all power from the library, remove the power cord from each outlet. The power button removes power from portions of the library and the drives, but the power supplies still have AC power at their inputs. 4. Remove the protective plastic on the exterior surfaces of the library. 5. Turn ON the library using the power button.
Item Default Setting Bar Code Label Length 8 Library Mode Random AutoClean Disabled Encryption Application Managed Encryption (AME) For a full list of factory defaults, see “Configure: Save/Restore” on page 5-26. Configuring Your Library using the Web User Interface To configure your library using the Web User Interface, complete the following procedures: 1. “Establishing Remote Access to Your Library” 2. “Logging on to the Web User Interface” on page 4-22 3.
2. Press the DOWN button to highlight the Network menu. 3. Press the SELECT button to display the Network screen. 4. Select IP STACK, and press the SELECT button to highlight the Internet Protocol field. a. Press the DOWN or UP button to scroll through the Internet Protocol options. b. Press the SELECT button on the desired Internet Protocol. If you select IPv6 protocol, the Configure Network menu will include options for Stateless Autoconfig and Prefix length.
d. After entering the digits for the last octet of your Netmask address, press the SELECT button to apply your entries. 8. Press the DOWN button to select Gateway. For IPv4, enter only an IPv4 Gateway address. For IPv6, enter only an IPv6 Gateway address. For IPv4 & IPv6, enter a Gateway address for both IPv4 and IPv6. a. Press the SELECT button to highlight the Gateway field. b. Press the UP or DOWN button to select the digit(s) in the first octet of your library's Gateway address. c.
a77ug070 3. When the login screen appears, a. Select admin for a User ID. b. Enter secure for a Password. Figure 4-23. Log in screen on the Web User Interface Verifying/Updating Firmware It is important to run the latest level of firmware. To ensure that you are running the latest levels of library firmware, drive firmware, and SNMP MIB (Management Information Base) file, complete this procedure. 1. Verify the SNMP MIB file currently installed on your SNMP server.
4. Install the MIB file on your SNMP server. Refer to your server application documentation for instructions. Choosing General Library Settings If your library contains only one drive or logical library, both general and specific settings will be combined into one table (see Figure 4-24 on page 4-25). 1. Expand Configure Library in the left navigation pane of the Web User Interface. 2. Click General and enter the following: v Library Name - Enter a name for your library.
– Refresh - Click this button to update the current screen. – Apply Selections - Click this button to submit the changes made to the screen. Figure 4-24. The 2U library Configure Library: General screen Figure 4-25. Example: The 4U library Configure Library: General screen 3. If your library has more than one drive, proceed to “Choosing the Number of Logical Libraries for Your Library.” If your library has one drive, proceed to “Entering Path Failover Feature Activation Key” on page 4-26.
One cartridge magazine cannot be assigned to two logical libraries. If you partition a multi-drive library, each of the magazines must be assigned to a logical library on a magazine boundary. The entire magazine must be part of one logical library only. Note: If you have a 2U library with two drives, you have the capability to have two logical libraries.
Figure 4-28. Feature Key verification screen Note: Follow the instructions in the Dell PowerVault TL4000 Failover Configuration Guide to configure your environment for failover. Setting Up Encryption Note: Application Managed Encryption (AME) does not require a key. Library Managed Encryption requires a license key. The customer should contact their TSR (technical sales representative) to purchase this feature.
Minimum Prerequisites for Library Managed Encryption (LME) - LTO 5: v SAS and Fibre Channel LTO Ultrium 5 Tape Drive v Ultrium 5 Tape Cartridge v Library firmware level 9.00 or higher v Drive firmware level BBNE/BBNF or higher, for reference go to http://support.dell.com. v Encryption Key Manager application (IBM SKLM) Minimum Prerequisites for Library Managed Encryption (LME) - LTO 4: v SAS and Fibre Channel LTO Ultrium 4 Tape Drive v Ultrium 4 Tape Cartridge v Library firmware level 5.
v Internal Label - Selective Encryption: Check your tape backup software application documentation to see if this feature is supported. v Internal Label - Encrypt All: Check your tape backup software application documentation to see if this feature is supported. 7. A primary and secondary key management server can be set for each logical library. Each partition has its own Encryption and key management settings.
Topology a77ug095 FC-AL Loop ID Figure 4-31. The Configure Library: Drive screen 2. Select the desired settings for each drive listed (either SCSI, SAS, or Fibre Channel). See Figure 4-31. 3. Click one of the following: v Refresh - to update the current screen v Submit - to apply the changes made to the screen Entering Library Network Settings a77ug074 This page shows the current network configuration of the library and allows modification to the configuration.
After the Submit button has been clicked, depending on the changes made, you will either be disconnected and need to login again or reboot the library. Clicking the Refresh button will refresh the page and any changes made will not be retained. 2. Select a Protocol Stack - Choose IPv4 only, IPv6 only, or Dual Stack IPv4 & IPv6. If you choose Dual Stack IPv4 & IPv6, you must be prepared to enter both IPv4 and IPv6 IP addresses. The sections below will gray out depending on the choices made here. 3.
v Refresh - to cancel the changes made to the screen. v Submit - to apply the changes made to the screen. Note: Depending on the changes made, you will either be disconnected and need to login again, or reboot the library. If a reboot is required, the following Warning message will appear after the Submit button is clicked. Figure 4-33. Warning Screen The library must be rebooted or the changes will not take place.
v v v v User (if enabled) Superuser (if enabled) Admin Service Note: Only one password can be set for each Role. 4. Enter the New Password . The password has a maximum of 10 characters (A-Z, a-z, 0-9, @, , , ). 5. In Repeat Password, enter the new password again. 6. In Support Name, enter the name of the person that will be able to offer the user help with the library. Note: Only one support person can be configured for the entire tape library.
Figure 4-36. The Configure Library: Logs and Traces screen 2. For Error Log Mode, select Continuous so all information for logs and traces will be captured. 3. Trace Level and Trace Filter options can be changed by Service personnel only. 4. Click one of the following: v Refresh - to cancel all of your entries and leave the settings as they were. v Submit - to apply the changes made to the screen.
Note: If you attempt to enter a blank value for the Domain Name, a warning message will appear. It will say If you are using Event Notification then a value is required for the Domain Name. 7. Click one of the following: v Refresh - to cancel all of your entries and leave the settings as they were. v Submit - to apply the changes made to the screen. Configuring SNMP settings This page shows the current SNMP configuration of the library and allows modification to the configuration.
v Target 3 - IP Address - Enter an optional third IP address where SNMP traps are sent, or leave as 0.0.0.0. v Version - The library offers three versions of the SNMP protocol; v1, v2, and v3. Select a version for each Target IP address. v Audit Logging - If SNMP is enabled and Audit Logging is enabled, the library sends SNMP traps to an SNMP Management console when the library or tape drive configuration changes. Note: This option is available only if the library firmware is 9.
Important: If you click the X in the upper right corner of your internet browser window, you will not log out of the Web User Interface.
Verifying the Connection 1. Depending on the server configuration, you may need to change the SCSI ID or Fibre Channel Loop ID of the library, if the current ID is the same as another device on the bus. 2. When the host server is powered ON, install the software and/or driver(s) that are compatible with the library. Backup software packages may require additional software or licensing to communicate with the library accessor. 3. If this is a SCSI attachment, ensure the library is properly terminated.
a77ug241 a77ug242 Figure 4-39. 2U library left magazine Figure 4-40. 2U library right magazine 2U Library I/O station The I/O (input/output) station (see Figure 4-41 on page 4-40) in a 2U library is part of the left magazine. To open the I/O station, select Control > Open I/O Station. The I/O station slot opens, and the "Unlocking I/O station" message displays.
a77ug248 Figure 4-41. 2U library I/O station in the left magazine 4U library cartridge magazines a77ug245 The 4U library has four cartridge magazines, two on each side (see Figure 4-42 and Figure 4-43 on page 4-41). The upper left magazine has 12 storage slots. The lower left magazine has 9 storage slots and houses the elective 3-slot I/O station ( 1 in Figure 4-42). The upper right magazine has 12 storage slots. The lower right magazine has 12 storage slots.
a77ug249 Figure 4-43. 4U library right magazines 4U library I/O station The I/O station in a 4U library (see Figure 4-44) is part of the lower left magazine. To open the I/O station, select Control > Open I/O Station. The I/O station slot opens, and the "Unlocking I/O station" message displays. Wait for the "Insert/remove cartridge and close I/O station" message to insert or remove the cartridge, then close the I/O station by gently pushing the slot back into the left magazine.
a77ug247 1 Figure 4-45. Finger Holes on back side of 4U library I/O station Populating the Library with Data Cartridges Important: Cartridges placed in the library must be labeled with the correct bar code labels. For additional information, see Chapter 6, “Using Ultrium Media,” on page 6-1. For information on working with the cartridge magazines, see “Cartridge magazines” on page 4-38. 1. Properly label the data cartridges. Refer to Chapter 6, “Using Ultrium Media,” on page 6-1. 2.
5. Put magazines back into the library. The library will automatically start up and perform an inventory check. Inserting the Cleaning Cartridge Important: Cleaning cartridges placed in the library must be labeled with the correct bar code labels. For additional information, see Chapter 6, “Using Ultrium Media,” on page 6-1. Note: Earlier versions of the 4U library contained a Dedicated Cleaning Slot (DCS). This DCS can be retained and is supported by future library firmware updates.
Note: A user has the option to perform manual cleaning by navigating in the RMU to Service > Clean Drive. In units with more than one drive to be cleaned, the user must manually refresh the screen after the clean has completed in order to be able to select an additional drive to be cleaned. 4. Replace the cleaning cartridge, if needed. v A cleaning cartridge must be replaced after 50 uses. To determine the number of cleaning uses remaining, click on the Web User Interface, Monitor Library->Inventory .
Chapter 5. Operations The following table lists menu navigation shortcuts to activities that can be performed via the Operator Control Panel and/or the Web User Interface. Before using the Operator Control Panel or the Web user Interface, please review the information in Chapter 3: User Interfaces. Table 5-1.
Table 5-1.
Table 5-1. Menu navigation shortcuts (continued) Information/ Activity Menu Navigation Shortcuts Operator Control Panel Display Contrast Service > Display Contrast DNS, modify settings Not available with this interface. Drive, change interface configuration Configure > Drive > Drive Interface Drive, change SCSI/Loop ID For More Info “Service: Display Contrast” on page 5-32 Web User Interface For More Info Not available with this interface.
Table 5-1. Menu navigation shortcuts (continued) Information/ Activity Menu Navigation Shortcuts Operator Control Panel For More Info Web User Interface For More Info Drive Dump, save Not available with this interface. Service Library > Save Drive Dump “Service Library: Save Drive Dump” on page 5-61 Encryption, activate Not available with this interface. Configure Library > Encryption “Configure Library: Encryption” on page 5-46 Encryption, configure Not available with this interface.
Table 5-1.
Table 5-1.
Table 5-1. Menu navigation shortcuts (continued) Information/ Activity Slots, number empty Menu Navigation Shortcuts Operator Control Panel Monitor > Library > Status Slots, reassign Note: Varies according to the number of active, number logical libraries.
3 4 a77ug254 2 1 Figure 5-1. 2U Library Control Keys 2 4 3 a77ug253 1 Figure 5-2. 4U Library Control Keys Table 5-2. Library Control Keys Control Keys Description 1 UP (∧) - Upper-left button Used to scroll upward through menu items. 2 CANCEL (X) - Upper-right button Used to cancel a user action and return to the previous menu screen. 3 SELECT (') - Lower-right button Used to display a sub-menu or force an accessor action.
1. Press the UP ( 1 ) or DOWN( 4 ) keys to enter Interaction Mode. The Main Selection Menu will appear. The Main Selection screen shows Monitor, Control, Configure, and Service. 2. Scroll to your selection, then press the SELECT ( 3 ) key. The sub-menu for the selected menu item will appear. 3. Use the UP ( 1 ) or DOWN( 4 ) and SELECT ( 3 ) keys to scroll until you get to the area/screen you wish to configure. 4. Use the CANCEL ( 2 ) key if you wish to move backwards through the menu selections.
Monitor Control Configure Service Library Open I/O Station Logical Libraries Library Verify Drive Move Cartridges Library Settings Run Tests Inventory Magazines Re-Inventory Drive Service (Drives) Network Display Contrast Set Access PIN Telnet Service Port Save/Restore Control Path Failover a77ug050 Set Date and Time Figure 5-3.
Monitor Library Status Identity Status Serial Number Act. Cart. Version Error Log Network IPv4 IPv6 IP Stack On Time Vendor ID Slots Empty Product ID Moves Active Slots I/O Station DHCP ON-OFF Stateless autoconfig Netmask Prefix Length Static IPv6 Address WWNN Lib. x Mode Note: x = number of logical libraries (1-4 partitions) An example with a library with 4 partitions: Lib.1 Mode Lib.2 Mode Lib.3 Mode Lib.
v Identity v Error Log v Network Under Monitor > Library > Status are the following items: v Status - Status of the library v Act.
Monitor Drive Status Identity Drive (n) Drive (n) Status Firmware Rev Activity Vendor ID Source Product ID Encryption Serial Number Topology (A) Port A Status Speed (A) Speed (A) Loop ID (A) Hashed Address (A) Speed (A) Port B Status Loop ID (A) WWNN PID (A) SCSI ID SCSI Drive Topology (A) PID (B) Version* SAS Drive Fibre Channel Drive Version* Hashed Address (B) Fibre Channel Drive *Ultrium 3 and 4 half high SAS drive sleds and Ultrium 4 Fibre Channel drive sled may be list
Under Status and Drive (n) are the following items: v Status - the current status of the drive v Activity - the current action being performed by the drive v Source - the serial number of the cartridge currently in the drive v Encryption - indicates the type of data encryption currently set for the selected drive (will not appear on Gen3 or SCSI drives) v Topology - the topology chosen for a fibre library (see “Fibre Channel Interface” on page 3-10) v Speed - indicates the speed of the fibre channel (fibre
Monitor Inventory Magazines Drive (n) Upper Left Upper Right Lower Left Lower Right (Graphic of left magazine) (Graphic of right magazine) a77ug036 (Drive status) Figure 5-6. Example of a 4U Monitor: Inventory menu Note: 2U has a single right-side magazine. Under Magazine choose one of the following to see a graphical representation of the cartridge magazine(s). Slots containing cartridges will be highlighted.
Note: Left magazine of a 2U Library has a 1-slot I/O Station. The black boxes are inventoried cartridges. Press the up and down keys to scroll. Note that this magazine has a 3-slot I/O Station. These slots can be changed to storage slots if needed. See “Configuring I/O Stations and Reserving Slots” on page 5-67. Press SELECT to display all empty slots and cartridge serial numbers in the associated magazine. Figure 5-8. Detailed information on cartridges residing in a magazine Table 5-3.
Important: Wait for the messages before you insert or remove cartridges to ensure that the library is ready to handle the cartridges. After the I/O station is closed, you must wait for the library to complete its inventory before normal library operations commence. Control: Move Cartridges Use this menu item to move cartridges in the library. Control Source Type Source Volume Serial Destination Type Destination a77ug053 Move Cartridges Figure 5-10.
Control Left Right "Left magazine unlocking" "Right magazine unlocking" a77ug054 Magazine Figure 5-11. Control: Magazine menu Choose "Left" or "Right" to unlock the corresponding cartridge magazine(s). The magazines can now be removed from the library by gently pulling each magazine out of the library. To replace a magazine, insert the back of the magazine into the front of the library and gently push the magazine into the library. The magazine will lock when inserted into the library.
v Set Access PIN v Save/Restore v Set Date and Time Configure: Logical Libraries Use this menu item to select the number of logical libraries. The Currently Configured - x section shows the number of logical libraries currently configured. Figure 5-13. Configure: Logical Libraries menu Note: The maximum number of Logical Libraries in a 2U is two. Note: This menu is only available on libraries with multiple drives.
Configure: Library Configure Logical Library Settings Logical Lib Settings General 1 3 2 4 Auto Clean Mode I/O Station(s) enabled Host Label Length Random Sequential Autoload Active Slots a77ug056 Loop Figure 5-14. Configure: Library menu Note: The Remove DCS No is only available on libraries with the DCS feature.
- Autoload: Sequential mode with autoload mode ON loads the first available cartridge (slot with the lowest numerical value that contains a cartridge) automatically if the library powers ON with an empty drive. - Loop: Sequential mode with loop mode ON loads the cartridge in the lowest numerical slot after the cartridge in the highest numerical slot has been filled and sent back to its home slot. This allows endless backup operations without user interaction.
Note: The universal cleaning cartridge has a bar code CLNUxxLx. This cleaning cartridge is used to clean all LTO generation tape drives. For Auto Clean to function, the following criteria must be met: – On 4U libraries with library firmware of .80 or lower that still contain a Dedicated Cleaning Slot (DCS), or 4U libraries with library firmware higher than 1.95 that chose to retain the DCS in their library, a CLN cartridge must be present in that slot.
Configure: Drive Configure Drive Control Path Drive Interface SAS drives do not require user configuration SCSI ID A Speed A Type Fibre Channel Drive a77ug299 A Loop ID Figure 5-15. Configure: Drive menu The following items are in this menu: v Drive Interface - use this to assign a SCSI ID to a SCSI drive or to assign a Port Speed, Port Type, and Loop ID to a Fibre Channel drive. SAS drives do not require user configuration.
Configure: Network Configure Network IP Stack DHCP-ON DHCP-OFF (IPv4 & IPv4+IPv6) DHCP-OFF (IPv6) IP Address Stateless autoconfig Netmask Prefix Length Static IPv6 Address Ethernet Gateway Ethernet a77ug043 Gateway Figure 5-16. Configure: Network menu Use these menu items to change the current network settings which allow you to access the library remotely via a web browser. v IP Stack - Choose IPv4 only, IPv6 only, or IPv4 & IPv6.
v Netmask - the Network Mask address of the library v IP Stack - the IP Stack manages static IP addresses v Stateless autoconfig - allows IPv6 hosts to be configured automatically when connected to a routed IPv6 network v Prefix length - the length of the IP address prefix v Static IPv6 address - a static IPv6 address that has been assigned to the library v Gateway - the Gateway address of the library v Ethernet - the current speed setting of the ethernet interface v DNS Server 1 - the first DNS server addr
2. 3. 4. 5. 6. Press the SELECT button to highlight the first digit of the 4-digit Access PIN. Use the UP and DOWN buttons to select each digit. Press the SELECT button to move to the next digit. Repeat these steps for repeating the Access PIN. After entering the final digit, press the DOWN button and select one of the following: v Save - to apply your settings. v Cancel - to delete your settings.
Configure Restore Passwords Restore All Restore Library Config. Save Library Config. a77ug045 Save/Restore Figure 5-19. Configure: Save/Restore menu v Restore Passwords - This menu item restores the factory default for both the RMU Admin user access password and the service password. v Restore all - This menu item restores all factory default settings (refer to Table 5-4). v Restore Library Config - This menu item restores your saved library configuration from a USB device.
Table 5-4. Factory Default Settings (continued) Restored Item Default Setting* Comments DHCP Enabled Note: DNS server addresses, if available, will be automatically assigned. If the DHCP server does not find any DNS server, the DNS fields will be set to "0.0.0.0".
Configure: Set Date and Time Use this menu item to set the current date and time in your library. a77ug046 Configure Set Date and Time Figure 5-20. Configure: Set Date and Time menu Configure: Path Failover Use this menu item to enter the Path Failover Feature Activation key (Supported on 4U library only for library firmware levels at or below 8.xx. Supported on both the 2U and 4U libraries with library firmware levels above 8.xx). Path Failover a77ug119 Configure Figure 5-21.
Library Verify a77ug047 Service Figure 5-22. Service: Library Verify menu 1. On the Operator Control Panel, navigate to Service > Library Verify and start diagnostic. v Push the Select key to highlight the drive field. Use the Up/Down keys to select the drive. Push the Select key to complete the selection. v Push the Down key to highlight . v Push the Select key to execute Library Verify. 2.
Note: After running the System Test or the Slot to Slot Test, the library will need to be re-inventoried. It might be required to reboot the library after library diagnostics completes to ensure proper library re-detection on some backup applications. Service: Service (Drives) Service Clean Drive Drive Tests Drive Power a77ug058 Service Figure 5-24.
changes. When configuration changes of a disabled drive are made from the Web Interface (RMU), the drive does not power ON after committing changes. Service: Display Contrast Display Contrast a77ug170 Service Figure 5-25. Service: Display Contrast menu The following display contrast settings are available in this menu: v The numbers 1 through 10 will display, with 10 being the lightest shade and 1 being the brightest.
Table 5-5. Web User Interface Menus (continued) User Access Date & Time Logs & Traces Email Notification SNMP Save/Restore - Service Library Clean Drive Advance Diagnostic (for Service Personnel only) View Logs View Drive Logs Save Drive Dump Perform Diagnostics Key Path Diagnostics (if feature is available) Upgrade Firmware Reboot Monitor Library Menu The Monitor Library menu contains the following sub-menu items.
Table 5-6. Library Identity page elements (continued) Menu Item Description 2U 4U IPv6 static assigned address This is your library's IPv6 static assigned address. X X Router discovery This is the IPv6 router discovery address assigned to your library. IPv6 address Note: There may be more than one IPv6 discovery address if there is more than one IPv6 router available in your network environment. X X MAC Address This is the machine's access code assigned to your library.
Table 5-7. Drive Identity page elements (continued) Menu Item Description 2U Library SCSI Fibre 4U Library SAS SCSI Fibre SAS X X X X Version Only Version 2 (V2) half-high drives will have a separate version line with the number 2. X X Firmware Revision This is the current level of firmware installed on the X drive. For information on updating your firmware, refer to “Service Library: Upgrade Firmware” on page 5-63.
a77ug288 Figure 5-27. The 4U library Monitor Library: Drive Identity page showing one Ultrium 3 SAS half height V2 drive (#1) and one Ultrium 4 SAS half height drive (#2) Monitor Library: Library Status This page displays the dynamic information about the library, such as the current status of the components. No changes can be made from this page. Table 5-8 lists all available elements on the Library Identity page. An "X" indicates that the element displays for the specified library type. Table 5-8.
Table 5-8. Library Status page elements (continued) Menu Item Description 2U 4U 1. Right Magazine This displays whether the lower right magazine is "Present" or "Not Present". X 2. Left Magazine This displays whether the upper left magazine is "Present" or "Not Present". X 2. Right Magazine This displays whether the upper right magazine is "Present" or "Not Present". X Figure 5-28.
Table 5-9. Drive Status page elements (continued) Menu Item Description 2U Library SCSI Fibre Port B Status Indicates whether Port B is logged on or out. Port Name The name that is assigned to the Port on the drive. X Speed The speed setting of the drive. Choices are Auto (where the drive automatically negotiates the speed of the drive to match that of the server), 1 Gb/s, 2 Gb/s, 4 Gb/s, or 8 Gb/s for Fibre Channel; 3 Gb/s or 6 Gb/s for SAS. X Topology The type of connection to the host.
a77ug093 Figure 5-29. The 4U library Monitor Library: Drive Status page Term Definitions: v BOP (Beginning of Partition): BOP (Beginning of Partition) is a SCSI term, which in a single partition format is the same as beginning of tape. It means that policy is determined on writes at LB zero. Appending to a tape [or overwriting at a non-zero LB] does not change the policy already in use for that tape. v Key Path: The avenue where key resolution is completed.
Inventory As Of 14:02:04 Library Time Drive Inventory Drive 1 Status Empty Label Source ------------- Magazine Inventory 9 10 11 4 5 6 7 1 2 3 IO-Station 23 19 22 21 20 18 17 16 15 14 13 12 Refresh Figure 5-30.
a77ug099 *Res* Figure 5-31. The 4U library Monitor Library: Inventory page (Right Magazines) Note: The 4U graphic shows the Slot Inventory for the right magazines of this library as an example. The left magazines are similar. Manage Library Menu The Manage Library menu contains the following sub-menu items.
a77ug072 Figure 5-32. Manage Library: Move Media page The following elements appear in the Source and Destination screens. Element In the Source screen, this identifies the library element that contains a cartridge. In the Destination screen, this identifies the library element that is empty and can receive a cartridge. Volume Serial In the Source screen, this element displays the serial number of the cartridge. In the Destination screen, this element contains no information.
Configure Library Menu The Configure Library menu contains the following submenu items: v “Configure Library: General” v “Configure Library: Logical Libraries” on page 5-44 v “Configure Library: Path Failover” on page 5-45 v v v v v v v “Configure “Configure “Configure “Configure “Configure “Configure “Configure Library: Library: Library: Library: Library: Library: Library: Encryption” on page 5-46 Drives” on page 5-48 Network” on page 5-50 User Access” on page 5-52 Date & Time” on page 5-54 Logs & Trace
Table 5-11. Configure Library: Specific page elements (continued) Menu Item Description 2U 4U Active Slots It may be necessary to modify the number of active slots to agree with the number of slots allowed by your host software. To modify the number of active slots in your library, click on the drop down list and select the number of slots you want active in your library. Also, the Auto Clean function requires the cleaning cartridge to be in a DCS or reserved slot.
Note: When reducing the number of drives in your library, update the Logical Library configuration. This will remove the Attention LED on the front panel and the exclamation mark on the Home screen indicating that a drive is missing. a77ug098 Updating the Logical Library configuration will also update the drive element addressing and drive numbering.
Note: Follow the instructions in the Dell PowerVault TL4000 Failover Configuration Guide to configure your environment for failover. Configure Library: Encryption Note: Application Managed Encryption (AME) does not require a license key. Library Managed Encryption requires a license key. Contact your TSR (technical sales representative) to purchase this feature. Important: The Advanced Encryption Settings are for Engineering Support use only. These fields should always be set to "No Advanced Setting".
v v v v v SAS and Fibre Channel LTO Ultrium 4 Tape Drive Ultrium 4 Tape Cartridge Library firmware level 5.80 or higher Drive firmware level 77BE or higher Encryption Key Manager application (IBM SKLM) a77ug199 Setting or Changing a Drive's Method of Encryption 1. Enter your library's IP Address in an internet browser address field and press ENTER. 2. Log in to the Web User Interface. Refer to “Login” on page 2-5. 3. Expand Configure Library in the left navigation panel. 4. Click Encryption.
7. Select Enable SSL for EKM to enable Secure Sockets Layer for the IBM SKLM application. 8. Select an Encryption method, from the pull down menu, for each logical library. v Without an encryption license key, select None or Application Managed Encryption. v With an encryption license key, select Library Managed Encryption. 9. Select an Encryption policy, from the pull down menu, for each logical library. v Encrypt All: This is the default policy.
Table 5-12. Drive Identity page elements Menu Item Description 2U Library SCSI Fibre SAS 4U Library SCSI Fibre SAS SCSI ID For each SCSI drive, click on the drop down list and select the number of the slot in which the drive is located. X X Power On For each drive, click in the box to power ON the selected drive. X X X X X X Control Path The control path drive communicates messages from the host to the library. Select this option for each drive that you want to be a control path drive.
Topology a77ug095 FC-AL Loop ID Figure 5-42. The Configure Library: Drives page for a 4U library Click one of the following: v Refresh - to cancel the changes made to the screen. v Submit - to apply the changes made to the screen. Note: When configuration changes of a disabled drive are made from the Operator Control Panel (OCP), the drive powers ON after committing changes.
After the Submit button has been clicked, depending on the changes made, you will either be disconnected and need to login again or reboot the library. Clicking the Refresh button will refresh the page and any changes made will not be retained. 2. Select a Protocol Stack - Choose IPv4 only, IPv6 only, or Dual Stack IPv4 & IPv6. If you choose Dual Stack IPv4 & IPv6, you must be prepared to enter both IPv4 and IPv6 IP addresses. The sections below will gray out depending on the choices made here. 3.
v Refresh - to cancel the changes made to the screen. v Submit - to apply the changes made to the screen. Note: Depending on the changes made, you will either be disconnected and need to login again, or reboot the library. If a reboot is required, the following Warning message will appear after the Submit button is clicked. Figure 5-44. Warning Screen The library must be rebooted or the changes will not take place. Configure Library: User Access This page allows the user to add and modify user accounts.
Check the Disable User check box if you do not want User to be listed on the Role listbox (that is, prohibits User login). Clear the check box to allow Superuser or User login. Passwords v Role - The name that is associated with the chosen Access Level. Choose from User, Superuser, Admin, or Service. Note: Admin can select User, Superuser, and Admin roles. Service can select User, Superuser, Admin, and Service roles.
change a password, or a restore factory default password from the operator panel (if the admin account is the one that is locked out). v Maximum Number Of Days Before Password Must Be Changed - Choose the maximum number of days before the password must be changed. The factory default value is 90. Possible range for this configuration option is 0 - 365. There is no limitation if 0 is selected. Click one: v Refresh - Cancels the changes that are made to the screen.
Figure 5-47. Configure Library: Logs & Traces page It is recommended that you select Continuous for the Error Log Mode so that all information for logs and traces will be captured. Click one of the following: v Refresh - to cancel the changes made to the screen. v Submit - to apply the changes made to the screen. Note: The trace level and trace filter selection options are only changeable by Service personnel.
Note: The TL2000/TL400 email address field cannot be empty (clear). The email notification setup allows the user to turn off the feature by deselecting the notify error and notify warnings boxes. The user can add an invalid email as long as the email address format is correct (i.e. a@xxx.xxx). SMTP Server Address (IPv4 or IPv6) Enter the address of the email server of the individual you would like to receive the errors and/or warnings. This can be an IPv4 or IPv6 address, or a host name and domain.
SNMP v Enabled - Check this box to have SNMP traps sent to an SNMP Management console. v Community Name - An SNMP community name is a text string that acts as a password to authenticate messages that are sent between the SNMP remote management application and the library. Enter your preferred name, or leave as "public". SNMP DESTINATIONS v Target 1 - IP Address - If SNMP traps are enabled, enter an IP address where SNMP traps are sent.
library using a configuration file that was saved with the same version of firmware currently installed in the library. Since the RMU can be accessed remotely, its implementation will save/restore the configuration data to/from a file on the host site. When entering commands on the OCP, the unit is accessed directly. For this reason the OCP implementation will save/restore the configuration data to/from a USB memory stick that is inserted into the USB connector on the library controller.
a77ug259 Figure 5-51. No Cleaning Required a77ug260 If there is no cleaning cartridge in the library, Clean cannot be selected and the Slot # displays N.A.. See Figure 5-52 Figure 5-52. No cleaning cartridge in library a77ug122 Note: If the library is configured for Auto Clean, and a cleaning cartridge is resident in a reserved slot, the library automatically loads the drive with a cleaning cartridge. The drive completes a cleaning and the library returns the cleaning cartridge to the reserved slot.
v v v v v v Options > Security > Custom Level > Downloads > Automatic Promptingfor file Downloads and File Downloads are both Enabled. Total Number of Entries Start Entry Number of Entries per Page View Clear Log - Clears the log you are viewing Dump Log - Dumps the log you are viewing v Save Service Dump - Creates a DPA (Dump All) log output that can be viewed or saved to a file a77ug120 buttons appear if the number of logs entries exceeds the number of entries per page.
a77ug096 Figure 5-55. Service Library: View Drive Logs screen Service Library: Save Drive Dump This menu item allows a drive memory dump to be saved to the host computer. 1. Select the drive. 2. Choose the regular drive memory dump option (data that is stored in flash), or the forced drive memory dump option (data that is stored in memory and moved to flash). 3. Click Save Drive Dump. When Save Drive Dump is clicked, the user has the option of saving the drive memory dump to their hard disk drive.
Service Library: Perform Diagnostics Note: When running the "System Test", the library must contain at least the same number of data cartridges as there are drives in that library. For example, if your library has 4 drives installed, you must have 4 or more data cartridges in the library prior to the start of the test. If there are fewer data cartridges than drives in the library, an error message "Slot Empty" will occur, and the test will not complete successfully.
v Drive Test: The library performs a drive communication test to confirm communication with the drive. v Ethernet Test: For each key management IP address, the library performs a ping test and records the results. v EKM Path Test: For each key management IP address that passed the ping test, the library performs a communication test. v EKM Config Test: This test confirms that a drive is correctly configured in the key manager to service key requests.
2. The library code must be updated first, unless noted otherwise. This action supports any changes that are introduced in the library code for that drive, or any changes that are made to the drive for that release. 3. These firmware updates are intended to increase overall reliability, improve tape handling, reduce the possibility of data errors, and enhance diagnostic capabilities. Note: Library firmware and tape drive firmware are verified and released together.
a77ug289 Figure 5-59. The Service Library: Upgrade Firmware page, showing one Ultrium 3 SAS Half Height V2 drive and one Ultrium 4 SAS Half Height drive. Service Library: Reboot Important: Some options of the Web User Interface take the library OFFLINE. This inactive mode can interfere with host-based application software, causing data loss. Ensure that the library is idle before attempting to perform any remote operations that will take the library OFFLINE. This page is used to perform a library reboot.
2. Pull out the I/O Station and insert a data cartridge(s). On a 2U library, only 1 cartridge can be inserted at a time. On the 4U library, 3 cartridges can be inserted at one time. 3. Close the I/O Station. The library will automatically start an inventory. The cartridges in the I/O Station will be counted but unassigned until they are moved into storage slots. 4. From the OCP Main Menu, select Control > Move Cartridges and move the data cartridges into the desired data slots.
3. Push the magazine back into the library. The library will automatically start an inventory. Note: If you run a library configuration backup program on your host computer, use the program to run an audit of the library after cartridges have been removed to update the backup program. Configuring I/O Stations and Reserving Slots 2U libraries usually have 1 slot for an I/O Station, while 4U libraries have 3 slots assigned as an I/O Station. These slots can be configured as storage if needed.
chosen for the reserved slot containing the cleaning cartridge. As with a library with a single logical library, this slot is the last physical slot in the library (top right magazine, uppermost rear slot). Note: Configure the required number of reserved slots prior to enabling Auto Clean. To reserve a cleaning slot, follow these steps.
Chapter 6. Using Ultrium Media Figure 6-1 shows the LTO Ultrium Data Cartridge and its components. 1 2 3 LTO cartridge memory Cartridge door Leader Pin 4 5 6 Write-protect Switch Label area Insertion guide Figure 6-1. The LTO Ultrium Data Cartridge Note: The same components are on all the LTO Ultrium Data Cartridges. Data Cartridges The different generations of Ultrium data cartridges can be identified by color: Table 6-1.
When processing tape in the cartridges, Ultrium Tape Drives use a linear, serpentine recording format. The native data capacity and recording format of Ultrium data cartridges is as follows: Table 6-2. Cartridge Data Capacity and Recording Formats Type Native Data Capacity Recording Format Ultrium 6 2500 GB (6250 GB at 2.
Cartridge Compatibility Table 6-4.
that lacks WORM-capable firmware from writing on a WORM tape cartridge. For LTO 6, native data capacity is 2500 GB and compressed data capacity is 6250 GB. v When the drive senses a WORM cartridge, the firmware prohibits the changing or altering of user data already written on the tape. The firmware keeps track of the last appendable point on the tape.
Table 6-5. Bar code label requirements for Ultrium tape drives and libraries (continued) Ultrium Tape Drive/Library Bar Code Label Requirements 3583 Required 3584 Required When read by a library's bar code reader, the bar code identifies the cartridge's VOLSER to the library. The bar code also tells the library whether the cartridge is a data cartridge or cleaning cartridge. In addition, the bar code includes the two-character media-type identifier Lx, where x equals 1, 2, 3, 4, 5 or 6.
T O 1 2 3 L6 a69i0360 L Figure 6-3. Sample bar code label on the LTO Ultrium 6 Tape Cartridge. The volume serial number (LTO123) and bar code are printed on the label. Guidelines for Using Bar Code Labels Apply the following guidelines whenever using bar code labels: v Do not reuse a label or reapply a used label over an existing label. v Before you apply a new label, remove the old label by slowly pulling it at a right angle to the cartridge case.
to become a scratch (blank) data cartridge. Do not write-protect scratch (blank) cartridges; the tape drive will not be able to write new data to them. 1 A67E0026 If you must manually set the write-protect switch, slide it left or right to the desired position. Figure 6-4. Setting the write-protect switch Table 6-7. Location of the write-protect switch 1 Write-Protect Switch Handling the Cartridges Attention: Do not insert a damaged tape cartridge into the drive.
Ensure Proper Packaging v When shipping a cartridge, use the original or better packaging. v Always ship or store a cartridge in a jewel case. v Use only a recommended shipping container that securely holds the cartridge in its jewel case during transportation. v Never ship a cartridge in a commercial shipping envelope. Always place it in a box or package.
Perform a Thorough Inspection After purchasing a cartridge and before using it, perform the following steps: v Inspect the cartridge's packaging to determine potential rough handling. v When inspecting a cartridge, open only the cartridge door. Do not open any other part of the cartridge case. The upper and lower parts of the case are held together with screws; separating them destroys the usefulness of the cartridge. v Inspect the cartridge for damage before using or storing it.
Environmental and Shipping Specifications for Tape Cartridges Before you use a tape cartridge, acclimate it to the operating environment for 24 hours or the time necessary to prevent condensation in the drive (the time will vary, depending on the environmental extremes to which the cartridge was exposed). The best storage container for the cartridges (until they are opened) is the original shipping container.
Chapter 7. Troubleshooting v The library consists of the following CRUs (Customer Replaceable Units): – Control Card (electronics, processor, memory, etc.) – Power Supply – Drive Sled (drive plus drive-to-library connectivity) – Cartridge Magazines v Service Spare: – Library Enclosure (accessor, Operator control panel display, etc.
Table 7-1. Troubleshooting table (continued) Problem Solution ENCRYPTION Encryption Error: Displayed when the drive detects an error associated with an encryption operation - if the problem occurred while the tape drive was writing data to, or reading data from, tape 1. Check the host application to ensure the key management application is providing the correct encryption key. v Refer to the “Drive Sense Data” on page C-7 returned for an encryption operation.
Table 7-1. Troubleshooting table (continued) Problem Solution FRONT PANEL LEDs Attention LED To determine why the Attention LED is turned ON, log in to the Web User Interface and select Service Library > View Logs > Warning Trace. Drive Sled Issues: v Refer to “Isolating Drive Sled Problems” on page 7-9. v Whenever there is a hardware configuration change such as drives being swapped with different form factors (i.e. HH to FH or FH to HH), a library configuration change is needed.
Table 7-1. Troubleshooting table (continued) Problem Solution Determining current firmware levels Many problems can be resolved by a firmware upgrade. Ensure that both the library and drive firmware are at the latest levels available. v Library firmware: Monitor > Library > Identity > Version v Drive firmware: Monitor > Drives > Identity (select a drive) > Firmware Rev Update library firmware Refer to “Service Library: Upgrade Firmware” on page 5-63.
Table 7-1. Troubleshooting table (continued) Problem Solution Cartridge VOLSER is reported as "unknown" Probable cause: cartridge with no label or damaged label. Ensure that cartridge is properly labelled. If cartridge is properly labelled, unload the cartridge from drive and perform an inventory (OCP: Control > Re-Inventory; Web: Manage Library > Perform Inventory). If VOLSER is again reported as "Unknown", run Library Verify (Service > Library Verify).
Installation Problems Problems encountered during the installation of the library are usually caused by improper SCSI bus configuration, application software configuration errors, or an incorrectly configured operating system. If the application software that you are using is not communicating with the library after installation, check the following: v Accessor Ship Lock Key: Ensure that the Accessor Ship Lock Key on the top cover has been removed before powering on the library.
Ensure that the proper device driver, if applicable, is installed for the library. Note: Many backup applications use their own drivers for the library and drive. Before installing a driver, make sure it will not be in conflict with the software. Contact your Backup Application vendor for this information.
6 1 2 4 5 a77ug136 3 Figure 7-1. A 250w power supply with LEDs 4 5 a77ug198 6 Figure 7-2. A 80w power supply without LEDs Table 7-2. Power Supply LED Meanings 7-8 1 If the blue LED is lit, AC voltage is available. 2 If the amber LED is lit, there is a possible fan problem or other power supply issue. The power supply will need replacement. 3 If the green LED is lit, DC power is OK and active.
If the Library does not power on: 1. With library power OFF and the power cord unplugged, loosen the three thumb screws ( 5 ), grasp two of the thumb screws, pull the power supply out half way, reseat the power supply, and tighten the three thumb screws. 2. Ensure the power cord is plugged in at the power supply ( 6 ) and at the electrical outlet, then turn library power ON. 3. 4. 5. 6. 7. a. For power supplies with LED's, the "Blue" LED will be lit if AC power is good. b.
Note: If you are instructed by Dell Technical Support to copy the drive dump to your host computer, use one of the following methods: v Web User Interface: Refer to “Service Library: Save Drive Dump” on page 5-61. v ITDT: Refer to “Using the ITDT Firmware Update, Dump Retrieval and Drive Test Tool ” on page 9-5. 2. Ensure that the drive firmware is at the latest level.
4. 5. 6. 7. v If the card appears to have no abnormalities, reseat the card back in the library, tighten the thumb screws, and turn library power ON. If both the Operator Control Panel and Web User interfaces are inoperable or frozen and the latest firmware has been installed, the controller card CRU electronics is the most likely failure. If only the Web User Interface has failed, please see “Isolating Web User Interface Problems” before replacing any CRUs.
Isolating Accessor Scanner Problems If the server has reported inventory problems relating to inability to read bar code labels, or, if some or all of the cartridge labels are not being displayed on the Web User Interface, use the following procedure to determine if the scanner (library enclosure CRU) needs to be replaced. 1. Ensure that a supported bar code label (or labels) are being used. 2.
4. Remove cartridge. If cartridge was reported as Bad, properly dispose the cartridge. 5. Close the I/O Station. If the amber LED was lit because of bad media, the Attention LED will turn OFF. If the amber LED is still on, check the power supply or the power supply fans. See “Isolating a Power Supply Problem” on page 7-7. Chapter 7.
7-14 Dell PowerVault TL2000 Tape Library and TL4000 Tape Library User's Guide
Chapter 8. Error codes If an error occurs during operation of the library, the library stops the current operation and displays an error code on the LCD screen. Unless otherwise noted in “Error codes” on page 8-2, try to resolve the error by cycling power to the library and retrying the last operation. If the error persists, contact technical support. Example error code EVENT -6 8D 07 Where: v -6 indicates the position in sequence list, 0 being the most recent. v 8D 07 indicates the error.
Error codes Errors that are described are hard errors. If such an error occurs the library stops all operations and the Error LED starts flashing. An appropriate message is posted on the Operator Control Panel and the Web User Interface. These errors are also reported by way of email notification, if enabled. To enable email notifications, refer to “Configure Library: Event Notification” on page 5-55. Table 8-1.
Table 8-1.
Table 8-1. Main Error Codes (continued) Error Code Description User Action C0 Network initialization failed C1 Telnet Interface initialization failed C2 Webserver initialization failed C6 Ping command did not reach target C7 Cannot Upgrade from USB Not supported C8 Cannot Upgrade from FTP 1. Retry the Firmware upgrade. C9 Cannot Upgrade Robotic from Flash 2. If the error recurs, contact technical support. D0 ROM error. ROM checksum incorrect D1 RAM error.
Table 8-1. Main Error Codes (continued) Error Code Description DE Warning Event! See Table 8-3 on page 8-11 DF Warning Event! See Table 8-3 on page 8-11 E0 Incompatible magazine that is detected User Action 1. Remove magazine from library. 2. Insert magazine in library. If error recurs, contact technical support. E2 New hardware found. Library firmware upgrades required. Upgrade library firmware to the latest version. EB Power supply health check failed because of a power supply failure.
Table 8-1. Main Error Codes (continued) Error Code Description F1 User Action Drive Communication Error Library controller lost communication to drive The subcode indicates which drive is affected. Example: Subcode 02: drive #2 F2 Drive Sled not present The subcode indicates which drive sled is affected. Example: Subcode 02: drive sled #2 F3 Drive Hardware Error The subcode indicates which drive is affected.
Table 8-1. Main Error Codes (continued) Error Code Description User Action F6 No drive installed. A drive was never installed F7 Support ticket download from drive not possible F8 Invalid drive command F9 Invalid drive parameter FA SDCI microcode error FB Drive logged out FC Internal SCSI command failed with check condition FD Internal SCSI command timeout Refer to “Isolating Drive Sled Problems” on page 7-9. Sub Error Codes Table 8-2.
Table 8-2.
Table 8-2.
Table 8-2. Sub error codes (continued) 73 Error during move sled to block. 80 Opening I/O slot failed. 81 Error during movement to I/O slot open position. 82 Error during moving back - sensor was found. 90 Movement to home position failed. 91 Elevator movement to home position failed. 92 Error during sled movement to rotation position. 93 Error during rotation to home or far position. 94 Sled movement to home sensor position failed. 95 Sled movement to transport position failed.
Table 8-2. Sub error codes (continued) 97 Slot not free at robot unload 98 Cartridge not seated in load phase Warning events Warning events that are described are reported by way of email notification. The Attention LED flashes when warning events for the following occur: v Media v Fan v Redundant power supply An appropriate message is posted on the Operator Control Panel and the Web User Interface. Table 8-3.
Table 8-3. Warning events (continued) 48 SCSI: drive type not supported in this library Check whether a version of firmware is available that supports this drive type. For a list of supported drives, refer to “Ultrium Tape Drives” on page 1-9.
Table 8-3. Warning events (continued) 65 Invalid upgrade cartridge. Drive rejected Not supported the upgrade cartridge as invalid 66 Medium error; diagnostic tape write protected Ensure that diagnostic tape is not write protected. 67 Medium error, incompatible medium for write operation Replace incorrect cartridges. 6A Medium error, no OBDR tape Insert OBDR tape.
Table 8-3. Warning events (continued) DB External cooling fan error (fan motion stopped). The subcode indicates which drive sled fan is affected Refer to “Isolating Drive Sled Problems” on page 7-9. Subcode 01: drive sled #1(bottom) Subcode 02: drive sled #2 DC I2C Bus Failure DD Power Supply x fan failed, Redundancy might be at risk The subcode indicates which power supply fan is affected Refer to “Isolating a Power Supply Problem” on page 7-7.
Chapter 9. Service Procedures Removing Cartridges from Magazine Slots In the event of a severe mechanical problem with the library or if circumstances require you to remove tape cartridges, do the following. If the Operator Control Panel or the Web User Interface is still operational: 1. Move the tapes from the drive(s) to the magazines using the Manage Library > Move Media command (Web User Interface) or Control > Move Cartridges command (Operator Control Panel).
a77ug025 Figure 9-1.
a77ug024 Figure 9-2. Access holes for the right magazine 3. To manually release the magazines, push the end of a straightened paper clip into the access hole for each magazine at the back of the library. While holding the paper clip, have a second person pull the magazine out of the front of the unit. DO NOT push the paper clip in more than 1/2 inch. Chapter 9.
a77ug248 a77ug246 Figure 9-3. Left magazine pulled out of the 2U library Figure 9-4. Left Magazines pulled out of the 4U Library 4. If there are additional tapes still in the library, or if you were unable to manually remove the magazines and drive, contact technical support for further instructions.
Using the ITDT Firmware Update, Dump Retrieval and Drive Test Tool ITDT has multiple functional capability and is a very quick, convenient and efficient method for drive firmware updates. As a note, drive dump retrievals can be performed by the tool as well. The ITDT Tool: v Runs quick or extended diagnostics on tape drives.
9-6 Dell PowerVault TL2000 Tape Library and TL4000 Tape Library User's Guide
Chapter 10. Check, Adjust, Remove, and Replace Tools Required To service a library you may need one or more of the following tools: v #2 Phillips screwdriver v Ground strap (recommended, if available) Electrostatic Discharge Important: A discharge of static electricity can damage static-sensitive devices or microcircuitry. Proper packaging and grounding techniques are necessary precautions to prevent damage. Figure 10-1.
1 a77ug019 2 Figure 10-2. Shipping Lock and Label Storage Location 6. Insert the shipping lock ( 1 ) into the slot located on the center of the top of the library and secure with the shipping label ( 2 ). 1 a77ug018 2 Figure 10-3. Shipping Lock and Label 7. Pack the library in its original packaging materials (or equivalent packaging) for moving or shipping. Table 10-1.
Removing/Installing/Adding a Tape Drive Sled There are two types of drive sleds in a TL2000 library (2U library) and a TL4000 library (4U library). The contents of the ship groups are specific to the type of drive sled.
a77ug202 1 Figure 10-5. Library drive sled with ESD springs [1] (SAS sled shown) Removing a Tape Drive Sled 1. IT IS IMPORTANT TO PRESERVE A DRIVE DUMP FOR ANALYSIS IF ALL OF THE FOLLOWING CONDITIONS EXIST: v Library Error LED is ON. v Operator Control Panel is displaying a drive error message. v Web User Interface System Status screen is indicating that a drive has failed. IF NONE OF THE CONDITIONS LISTED ABOVE EXIST, PROCEED TO THE NEXT STEP. 2.
9 10 4 7 a77ug204 7 6 1 3 2 8 5 Figure 10-6. Drive sled components (full height fibre drive in top position, half height SCSI drive in middle position, half height SAS drive in bottom position) on back panel of a 4U library 1 SCSI cable 2 SAS cable 3 SCSI terminator 4 Fibre Channel cable 5 Ethernet cable 6 Power cords 7 Drive sled blue captive thumbscrews 8 Black pull-out tab 9 Drive sled 10 Drive sled handle 5.
a77ug027 Figure 10-7. Pulling the drive sled out of the library (drive sled without ESD springs shown) Installing a Tape Drive Sled Note: Power OFF the library before installing a SCSI drive sled. Fibre Channel and SAS drive sleds are hot pluggable and may be removed and installed while the library is powered ON. Important: In a 4U library a full height drive sled may be installed in drive slot 1 (drive will occupy slot 1 and slot 2) or drive slot 3 (drive will occupy slot 3 and slot 4).
a77ug028 Figure 10-8. Pushing the drive sled into the library (drive sled without ESD springs shown) 5. Tighten the captive thumbscrews ( 7 in Figure 10-6 on page 10-5) until the drive sled is secure. 6. If you are installing a drive sled without ESD springs (see Figure 10-4 on page 10-3), apply conductive tape to the sled as shown in Figure 10-9 on page 10-8. Chapter 10.
4U Library a77ug203 2U Library Figure 10-9. Diagrams for applying conductive tape for ESD protection to the back of a drive sled installed in a 2U or 4U library Note: The small gray markers show where conductive tape should be placed to provide ESD protection. 7. Push the black tab ( 8 in Figure 10-6 on page 10-5) back underneath the library. When inserted properly, only the handle of the tab will be visible. 8. Upgrade library firmware and drive firmware to the latest version.
Important: If the failed drive was configured for encryption, to ensure the replacement drive receives the proper encryption parameters, resubmit the encryption choices listed on Configure Library > Encryption for that particular drive or logical library even if the encryption settings did not change. Adding a Tape Drive Sled Use these instructions to add a new tape drive to your 2U or 4U Tape Library.
Configuring the Tape Drive 1. Log on to the Web User Interface. 2. Verify that you are running the latest versions of Library and Drive firmware. Upgrade the firmware at Service Library > Upgrade Firmware. 3. Use the Web UI to update the Logical Library (Configure Library > Logical Libraries) and Drive (Configure Library > Drives) configurations. Refer to Chapter 5, “Operations,” on page 5-1. Select Submit on the Configure Library > Logical Libraries web page even if there are no required changes.
a66mi096 Figure 10-10. A power supply being removed from a 2U library 5. Remove the packaging from the replacement power supply. 6. Grasp the top and bottom edge of the power supply and push it into the library. 7. Tighten the three blue captive thumbscrews on the power supply located on the back panel of the library. 8. 9. 10. 11. Connect the power cord to the library, then to the electrical source. Power ON the library using the power button on the front panel.
If the message "VPD Selection" is displayed at the Operator Control Panel, carefully highlight the “VPD from Enclosure" option to copy that version of the VPD to the new Library Controller Card. Then continue with the procedure. Removal and Replacement 1. Power OFF the library by pressing and holding the power button at the front of the library for 4 seconds. 2. Disconnect the power cord from the electrical source, then from the power supply or supplies at the back of the library. a66mi097 3.
Replacing Cartridge Magazines To replace a cartridge magazine, refer to one of the following procedures: v Using the Web User Interface, refer to “Manage Library: Release Magazine” on page 5-42. v Using the Operator Control Panel, refer to “Control: Magazine” on page 5-17. v If your library can not be powered ON, refer to “Releasing the Magazines Manually” on page 9-1. Replacing the Library Enclosure This procedure is necessary when the library enclosure, accessor, or display fails.
a77ug244 1 Figure 10-12. Removing the two mounting bracket screws anchoring the library to the rack (one screw on each side of the library) 5. Place the defective library on a clean and sturdy work surface. 6. Proceed to “Unpacking and Preparing the Replacement Library Enclosure.” Unpacking and Preparing the Replacement Library Enclosure Before installing the replacement library enclosure, it is important to verify that the enclosure is functioning properly. 1.
b. For a desktop library: 1) Carefully, lay the library on its side. 2) Peel the adhesive from the back of each of the six foot pads. 3) Install the foot pads on the bottom of the library enclosure by pressing each foot into one of the six areas ( 1 ) as shown in Figure 10-13. a77ug085 1 Figure 10-13. Foot pads installed on the bottom of the library enclosure 3. Carefully return the library to an upright position. 4.
a77ug195 Figure 10-14. Removing the shipping label and lock from the top of the library and storing on the rear panel 5. Store the lock and label on the back panel of the replacement library enclosure (see Figure 10-15). 1 a77ug019 2 Figure 10-15. Library shipping lock and label storage location on the real panel of the library 6. Proceed to “Installing your drive in the replacement library enclosure.
a77ug027 1. Remove all drives from the defective library (see Figure 10-16) and install them in the same positions in the replacement library enclosure. Figure 10-16. Removing a drive sled from the library (drive sled without ESD springs shown) a. Ensure that the power cord is unplugged from the power source for each power supply in the defective library enclosure. b. On the rear of the defective library, loosen the blue captive thumbscrews on the drive sled. c.
4U Library a77ug203 2U Library Figure 10-17. Drive sled taping diagrams Note: The gray markers show where conductive tape is placed. i. Push the black tab back underneath the drive sled. When inserted properly, only the handle of the tab is visible. 2. Power ON the replacement library enclosure. a. If power ON is successful, 1) After power up, the Ready/Activity LED ( 1 in Figure 10-20 on page 10-22) turns ON. a) If this message is displayed after the library powers ON, follow the instructions.
2. Swap the Power Supply in the defective library with the Power Supply in the replacement library enclosure. a. Remove the power supply from the defective library and from the replacement library enclosure. To remove a power supply from a library: 1) Loosen the three blue captive thumbscrews on the power supply. 2) Pull on two of the thumbscrews, on opposite sides of the power supply, and pull the unit away from the rear panel of the library.
Swapping Library Controller Cards IMPORTANT - READ ME BEFORE CONTINUING The Library Enclosure contains a copy of the vital product data (VPD) for your library. The VPD contains your current library configuration. A primary copy of this VPD is contained within the Library Controller Card. A backup copy of this VPD is maintained on the accessor in the enclosure (or chassis). When the Library Enclosure is replaced, the new enclosure electronics should contain zeros (0's) in key VPD locations.
a66mi097 Figure 10-19. Removing a Library Controller Card from the library Note: If you power on the replacement library without first swapping the Library Controller Card from the original (defective) library enclosure, the following message will appear on the Operator Control Panel shortly after applying power: "New library detected. Please remove library power and insert Library Controller Card from old Library".
1) The Error LED ( 4 in Figure 10-20) will turn ON. This indicates that the Library Controller Card from the defective library is not functioning properly. 2) Power OFF the replacement library enclosure. 3) Refer to Dell technical support for further instructions. 2 3 4 a77ug258 1 Figure 10-20. Library front panel LEDs 1 Ready/Activity LED (green) 3 Attention LED (amber) 2 Clean Drive LED (amber) 4 Error LED (amber) Swapping Cartridge Magazines 1.
a77ug025 Figure 10-21. Access hole for the left magazine (facing rear of library) Chapter 10.
a77ug024 Figure 10-22. Access hole for the right magazine (facing rear of library) b. Push the end of a straightened paper clip into the access hole for each magazine at the back of the library. DO NOT push the paper clip in more than ½ inch. While holding the paper clip, have a second person pull the magazine out from the front of the unit. Note: To prevent dropping the magazine, support both ends of the magazine before it clears the front edge of the library.
a77ug246 Figure 10-23. Left magazines pulled out of a 4U library (facing front of library) 2. Insert the cartridge magazines removed from the defective library into the same positions in the replacement library enclosure. 3. Insert the cartridge magazines removed from the replacement library enclosure into the same positions in the defective library to return to Dell. 4. Wait for inventory of the magazines to complete. a.
a77ug252 Figure 10-24. Mounting brackets and anchors for securing the library in a rack (one bracket and anchor on each side of the library) 2. With assistance, slide the replacement library enclosure onto the metal rails that are already in position in the rack (see Figure 10-25). Figure 10-25. Front view of rack showing screw placement 3. Tighten the mounting bracket screws ( 1 in Figure 10-12 on page 10-14) to anchor the replacement library enclosure to the rack. 4.
Desktop Installation: 1. Place the library in its permanent location. 2. Proceed to “Completing the Installation of the Replacement Library Enclosure.” Completing the Installation of the Replacement Library Enclosure 1. Connect all cables to the replacement library enclosure. 2. Power ON the replacement library enclosure. 3. Upgrade library firmware and drive firmware to the latest version. a. Visit http://www.support.dell.com/ to download the latest levels of library and drive firmware. b.
10-28 Dell PowerVault TL2000 Tape Library and TL4000 Tape Library User's Guide
Appendix A. SCSI Element Types, SCSI Addresses, and Physical Configurations For an overview of library partitioning and element addressing, see “Library Partitioning and Element Addressing” on page A-3. The following tables contain element addresses for the 2U library and the 4U library. Table A-1.
DTE assignments v Logical Library 1: Drive 1: 256 (0x100) v Logical Library 2: Drive 2: 256 (0x100) STE assignments v Logical Library 1: Slot 1 through slot 11 4096 (x1000) through 4106 (0x100A) v Logical Library 2: Slot 12 through slot 23 4096 (x1000) through 4107 (0x100B) Table A-3.
Table A-4.
that used to occupy two. As a result, the first half height drive position, or the first full-high drive position, will be called "Drive 1". The second half height drive position will be called "Drive 2". The third half height drive position, or the second full height drive position, will be called "Drive 3". The fourth half height drive position will be called "Drive 4".
When configured with two logical partitions, the Element Address assignments will be as follows: DTE assignments will be as shown in Figure A-2.
1: 2: 3: 4: Slot Slot Slot Slot 1 through slot 9 4096 (x1000) through 4104 (0x1008) 10 through slot 21 4096 (x1000) through 4107 (0x100B) 22 through slot 33 4096 (x1000) through 4107 (0x100B) 34 through slot 45 4096 (x1000) through 4107 (0x100B) Drive 4 Element Address 256 Drive 3 Element Address 256 Drive 2 Element Address 256 Drive 1 Element Address 256 Magazine 2 Magazine 4 Magazine 1 Magazine 3 Front side a77ug164 STE assignments v Logical Library v Logical Library v Logical Library v Logical
physically available or temporarily removed are reported. Empty (unused) slots located at the bottom or the top should not be reported, with an exception in case of a “removed” condition. A drive slot which does not contain a drive, and has a position between used slots, needs to be reported as a SCSI element. To signal the host application that this slot is not usable, its ACCESS bit will be disabled. Note: When reducing the number of drives in your library, update the Logical Library configuration.
A-8 Dell PowerVault TL2000 Tape Library and TL4000 Tape Library User's Guide
Appendix B. TapeAlert Flags This appendix is intended to provide additional information to the reader about the tape drive. All error code and diagnostic information contained in this chapter can be accessed from the Operator Control Panel of the Library. The drive portion of the Operator Control Panel Display will contain any drive error codes. Therefore there is no need to open the Library to access the buttons on the drive as described in this chapter.
04d Library Hardware D C v Ensure that the media changer and drives are not being used by any host, then reset the library from the front panel. v If the problem persists, contact technical support. 13d Library Pick Retry W There is a potential problem with the cartridge loader picking a cartridge from a drive or slot. v No action needs to be taken at this time. v If the problem persists, contact technical support. This flag is cleared when the next move command is received.
TapeAlert Flags Supported by the Drive Table B-1. TapeAlert Flags Supported by the Ultrium Tape Drive Flag Number Flag Description Action Required 3 Hard error Set for any unrecoverable read, write, See the Action Required column for or positioning error. (This flag is set in Flag Number 4, 5, or 6 in this table. conjunction with flags 4, 5, or 6.) 4 Media Set for any unrecoverable read, write, or positioning error that is due to a faulty tape cartridge. Replace the tape cartridge.
Table B-1. TapeAlert Flags Supported by the Ultrium Tape Drive (continued) Flag Number B-4 Flag Description Action Required 18 Tape directory corrupted Set when the drive detects that the in the cartridge memory tape directory in the cartridge memory has been corrupted. 19 Nearing media life Set when the tape cartridge is nearing 1. Copy the data to another tape its specified end of life. The flag is cartridge. cleared when the cartridge is removed 2. Replace the tape cartridge. from the drive.
Table B-1. TapeAlert Flags Supported by the Ultrium Tape Drive (continued) Flag Number Flag Description Action Required 53 Tape system area read failure Set when the tape system area could not be read successfully at load time. Copy the data to another tape cartridge, then discard the old cartridge. 55 Loading Failure When loading a tape into a drive, a Take this action if the tape cartridge hardware malfunction can prevent the will not load in the drive: tape from being loaded into the drive, 1.
B-6 Dell PowerVault TL2000 Tape Library and TL4000 Tape Library User's Guide
Appendix C. Sense Data When a drive encounters an error, it makes sense data available. You can use device drivers to examine the sense data and determine errors. The device drivers may conflict with some commercial software applications unless properly configured. To avoid conflicts on Windows operating systems, refer to your device driver's procedures for setting the driver to manual startup mode.
Table C-1.
Table C-1.
Table C-1.
Table C-1. Library Sense Keys, ASC and ASCQ (continued) Sense Key ASC ASCQ Description Hardware Error (04) (continued) 82h F4h Drive load timeout 82h F5h Drive unload timeout 82h F6h Drive never present 82h F7h Drive support ticket error 82h F8h Drive invalid command 82h F9h Drive invalid parameter 82h FAh SDCI microcode error 82h FBh Drive logged out 82h FCh Internal drive command failed with Check Condition 82h FDh Internal drive command timeout Appendix C.
Table C-1.
Table C-1.
Table C-2.
Table C-2. LTO Tape Drive Sense Data (continued) Bit Address or Name Byte 12-13 7 6 5 4 3 2 1 0 Additional Sense Code (ASC) Additional Sense Code Qualifier (ASCQ) Byte 12 Byte 13 ASC ASCQ 00 00 - No additional sense - The flags in the sense data indicate the reason for the command failure 00 01 - Filemark detected - A Read or Space command terminated early due to an FM The FM flag is set.
Table C-2.
Table C-2.
Table C-2.
Table C-2.
Table C-2. LTO Tape Drive Sense Data (continued) Bit Address or Name Byte 36-39 7 6 5 4 3 2 1 0 Port Identifier (Relative Target Port Address) Reporting Sense (This is the port address of the drive port through which sense is being reported. On Fibre Channel drives, it is the Fibre Channel Fabric Port Address [for example, 011E13 or 000026] with byte 36 being reserved. On SAS drives, it is the Hashed SAS Address of the drive port [for example, F32A94] with byte 36 being reserved.
Table C-2. LTO Tape Drive Sense Data (continued) Bit Address or Name Byte 7 6 65 5 4 3 2 1 0 Last Error FSC 66 67 Last Error Flag Data 68 69 LPOS Region 70-85 ERP Summary Information 86-89 Product Revision Level: YMDV (as defined in Standard Inquiry; this is also known as the Code Level) 90-95 Reserved (0) The descriptions below serve only as an overview of sense reporting in the tape drive. This tape drive conforms to all sense field reporting as specified in the SCSI standards.
means that the current direction is away from the physical beginning of the tape. A 1 means that the current direction is towards the physical beginning of the tape. 12. Relative LPOS fields (Bytes 30-33) reports the current physical position on the tape. 13. SCSI Address field (Byte 34) reports the SCSI Bus Address for the drive. Values returned range from 00h to 0Fh. 14. This field (Byte 35) contains the frame and drive number, passed across the RS-422 serial interface.
Appendix D. Enabling LUN Support in Linux To verify the detection of a tape drive, administrators should check for its entry in /proc/scsi/scsi. Current versions of Linux may not scan the logical storage unit (LUN) ID of every device. This can result in some TL2000/TL4000 devices not being identified or listed in the /proc/scsi/scsi output. Administrators can follow these steps to enable support for such devices. 1. Type cat /proc/scsi/scsi.
Red Hat Enterprise Linux RHEL doesn't automatically probe all LUNs on SCSI devices. The symptom shows LUN 0, which would be the drive, but not the loader. 1. Type #cat /proc/scsi/scsi. Attached devices: Host: scsi0 Channel: 00 Id: 06 Lun: 00 Vendor: IBM Model: ULT3580-HH3 Rev: 88M3 Type: Sequential-Access ANSI SCSI revision: 03 2. You will need to add the following to /etc/modules.conf options scsi_mod max_scsi_luns=255 Note: In RHEL 4, it is max_luns=255 3.
5. Add the /LUNS switch to the load line of the appropriate SCSI driver. If a dual channel card is installed and you are unsure which channel the LUN device is attached to, simply edit both lines. LOAD ADPT160M.HAM SLOT=201 /LUNS LOAD ADPT160M.HAM SLOT=202 /LUNS 6. After the STARTUP.NCF file has been edited, save the file and reboot the server to activate the new STARTUP.NCF. 7. Upon reboot navigate to the System Console and type scan all. This will start a scan of all the LUNS on each adapter. 8.
D-4 Dell PowerVault TL2000 Tape Library and TL4000 Tape Library User's Guide
Appendix E. Notes on IPv6 Compatibility with Windows 2003/XP and 2008/Vista IPv6 addressing is different from traditional IPv4 addressing. IPv4 addressing is listed in the format 255.255.255.255, with each value 1 byte, a total address of 4 bytes. IPv6 addresses require 16 bytes, and are listed in the format FFFF:FFFF:FFFF:FFFF:FFFF:FFFF:FFFF:FFFF, where there are 8 segments each 2 bytes long. Windows 2003/XP IPv6 support in Windows 2003 is not turned on by default.
v After upgrading the WinInet API (by upgrading to IE 7), the library RMU can be accessed from the browser by using the following format. – Replace all : with -. – Append s.ipv6-literal.net to the end of the IPv6 address. – For example, if the IPv6 address is fe80::1234:5678:abc and the interface number is 13, the address to browse to would be http://fe80--1234-5678abcs13.ipv6-literal.net.
Appendix F. SNMP Status MIB Variables and Traps Note: For additional information, refer to “SNMP Messaging” on page 1-7. Table F-1. SNMP Status Events Event Trap ID Definition Cold Start 0 Library has rebooted. Status Change 1 Library status has changed. Door Open 2 Library door has been opened. Mail Slot Accessed 3 Library I/O Station has been accessed. Fault Posted 4 Library has posted a hard fault/error. Request Drive Clean 5 Drive has requested a clean.
F-2 Dell PowerVault TL2000 Tape Library and TL4000 Tape Library User's Guide
Appendix G. Library Configuration Form Use this form when planning your library configuration. Keep this document in a secure location and update it when changes are made to the library configuration.
Drive types 4U Position 4: 4U Position 3: 2U/4U Position 2: 2U/4U Position 1: 4U Position 4: 4U Position 3: 2U/4U Position 2: 2U/4U Position 1: 4U Position 4: 4U Position 4: 4U Position 3: 2U/4U Position 2U/4U Position Position 3: 2U/4U Position 2U/4U Position 2: 1:4U 4U Position 4:4U Position 3:2U/4U Position 2:2U/4U Position 1: 2: 1: Fibre Channel Drive settings Logical Library: Position: Speed: Port type: Loop ID: Logical Library: Position: Speed: Port type: Loop ID: Logical Library: Position:
Appendix H. Accessibility Accessibility features help a user who has a physical disability, such as restricted mobility or limited vision, to use the HTML version of the customer documentation successfully. Features The major accessibility features for the HTML version of this document are: v You can use screen-reader software and a digital speech synthesizer to hear what is displayed on the screen. The following screen readers are tested: WebKing and Window-Eyes.
H-2 Dell PowerVault TL2000 Tape Library and TL4000 Tape Library User's Guide
Glossary This glossary defines the special terms, abbreviations, and acronyms that are used in this publication. If you do not find the term that you are looking for, refer to the index or to the Dictionary of Computing, 1994. Numbers 2:1 compression The relationship between the quantity of data that can be stored with compression as compared to the quantity of data that can be stored without compression.
archive To collect and store files in a designated place. ASCII American National Standard Code for Information Interchange. A 7 bit coded character set (8 bits including parity check) that consists of control characters and graphic characters. assigning a device The establishing of the relationship of a device to a running task, process, job, or program. assignment The naming of a specific device to perform a function.
buffer A routine or storage that is used to compensate for a difference in rate of flow of data or time of occurrence of events, when data is transferred from one device to another. bus A facility for transferring data between several devices that are located between two end points, only one device able to transmit at a specified moment. byte A string that consists of some bits (usually 8) that are treated as a unit and represent a character. A fundamental data unit.
compression The process of eliminating gaps, empty fields, redundancies, and unnecessary data to shorten the length of records or blocks. concurrent Refers to diagnostic procedures that can be run on one control unit while the rest of the subsystem remains available for customer applications. contingent connection A connection between a channel path and a drive that is caused when a unit check occurs during an I/O operation.
degausser A device that makes magnetic tape nonmagnetic. degradation A decrease in quality of output or throughput or an increase in machine error rate. degraded Decreased in quality of output or throughput or increased machine error rate. deserialize To change from serial-by-bit to parallel-by-byte. detented A part that is held in position with a catch or lever. device Any hardware component or peripheral device, such as a tape drive or tape library, that can receive and send data.
drive, magnetic tape A mechanism for moving magnetic tape and controlling its movement. Drive Not Configured This message occurs during the first boot after a factory settings restore is run. This message is not a real issue since it takes time for the library to configure. DRV Drive. DSA key Encryption key type. DSE Data security erase. DSP Digital signal processor. E EBCDIC Extended binary-coded decimal interchange code. EC Edge connector. Engineering change. ECC Error correction code.
EPROM Erasable programmable read only memory. EQC Equipment check. equipment check An asynchronous indication of a malfunction. Error log A data set or file in a product or system where error information is stored for later access. ESD Electrostatic discharge. ESP Encapsulating Security Payload. An Internet Protocol that provides origin authenticity, integrity, and confidentiality protection of a packet.
formatter Part of a magnetic tape subsystem that performs data conversion, speed matching, encoding, first level error recovery, and interfaces to one or more tape drives. FP File protect. frayed Damaged as if by an abrasive substance. FRU Field replaceable unit. FSC Fault symptom code. FSI Fault symptom index. FTSS Field Technical Sales Support. functional microcode Microcode that is resident in the machine during normal customer operation. G g Gram. GB gigabyte.
I IBM Security Key Lifecycle Manager (SKLM) IBM's EKM application that assists encrypting tape drives in generating, protecting, storing, and maintaining encryption keys that encrypt information that is written to and decrypt information that is read from tape media. ID Identifier. identifier (ID) (1) In programming languages, a lexical unit that names a language object; for example, the names of variables, arrays, records, labels, or procedures.
IP address An identifier for a computer or device on an Internet Protocol (TCP/IP) network. Networks that use the TCP/IP protocol route messages that are based on the IP address of the destination. See IPv4 and IPv6. IPL Initial program load. IP Stack A TCP/IP protocol stack that manages static IP addresses. IPv4 A network layer protocol for packet-switched networks. IPv4 supports 232 (about 4.3 billion) addresses. IPv6 A network layer protocol for packet-switched networks.
product and media. The “open” nature of LTO technology enables compatibility between different vendors' offerings by ensuring that vendors comply with verification standards. The LTO technology is implemented in two formats: the Accelis format focuses on fast access; the Ultrium format focuses on high capacity. The Ultrium format is the preferred format when capacity (rather than fast access) is the key storage consideration. An Ultrium cartridge has a compressed data capacity of up to 6250 GB (2.
meter In the Metric System, the basic unit of length; equal to approximately 39.37 inches. MIB Management Information Base. Information repository that is used by SNMP. micro One millionth of. microcode (1) One or more micro instructions. (2) A code, representing the instructions of an instruction set, which is implemented in a part of storage that is not program-addressable. (3) To design, write, and test one or more micro instructions. (4) See also microprogram.
node In a network, a point at which one or more functional units connect channels or data circuits. NTP Network Time Protocol. This protocol allows the library to set its internal date and time that is based on the date and time of a server. NVS Nonvolatile storage. A storage device whose contents are not lost when power is cut off. O oersted The unit of magnetic field strength in the unrationalized centimeter-gram-second (cgs) electromagnetic system.
Portable Document Format (PDF) A standard that is specified by Adobe Systems, Incorporated, for the electronic distribution of documents. PDF files are compact, can be distributed globally (by way of email, the web, intranets, or CD-ROM), and can be viewed with the Acrobat Reader, which is software from Adobe Systems that can be downloaded at no cost from the Adobe Systems home page. Private key A cryptographic key that is used to decrypt a message. PROM Programmable read only memory. PS Power supply.
RID tag Repair identification tag. RML Rack Mount Line. robot Picker. robotics Picker assembly. root CA certification In cryptography, a root certificate from a certificate authority (CA). RPQ Request for price quotation. RSA key Encryption key type. R/W read/write. S s Seconds of time. SAN Storage area network. SAS Serial Attached SCSI. A computer bus technology and serial communication protocol for direct attached storage devices.
servomechanism A feedback control system in which at least one of the system signals represents mechanical motion. signature A digital signature that is used in cryptography to identify one party to ensure authenticity. SKLM (IBM Security Key Lifecycle Manager) IBM's EKM application that assists encrypting tape drives in generating, protecting, storing, and maintaining encryption keys that encrypt information that is written to and decrypt information that is read from tape media.
special feature A feature that can be ordered to enhance the capability, storage capacity, or performance of a product, but is not essential for its basic work. SPI Security Parameters Index. SR Service representative, see also CE. SRAM Static random access memory. SS Status store. SSL (Secure Sockets Layer) A set of cryptographic protocols for secure communications on the Internet for such things as web browsing, email, Internet faxing, instant messaging, and other data transfer.
TCP/IP Transmission Control Protocol/Internet Protocol. TCU Tape control unit. TH Thermal. thread/load operation A procedure that places tape along the tape path. TM Tapemark. transport mode End-to-end communications security in which the end-point computers do the security processing. trusted certification In cryptography, a trustworthy certificate that is not registered with a certificate authority.
WORM Write Once Read Many. Write Write command. WT World trade. WWCID Worldwide Cartridge Identifier. WWN Worldwide Name. WWNN Worldwide Node Name. WWPN Worldwide port name. X XR External register. XRA External register address register.
I-20 Dell PowerVault TL2000 Tape Library and TL4000 Tape Library User's Guide
Index A Access PIN, Operator Control Panel 5-25 accessibility keyboard H-1 repeat rate of up and down buttons H-1 shortcut keys H-1 accessor 1-5 accessory package 4-2 active slots 5-20, 5-43 Active Slots 4-24 air quality 4-1 air vents, front panel 1-1 AME 5-46 Application Managed Encryption (AME) 4-27 ASC C-1 ASCQ C-1 auto clean 5-20, 5-43 Auto Clean 4-24 B Bar Code Labels 6-4 guidelines for using 6-6 bar code reader 1-5 bootcode firmware, current level 5-33 BOP 5-37 Border Gateway Protocol (BGP) 1-7 C ca
ITDT Tool K Key Path 5-37 Key Path Diagnostics keyboard H-1 N 5-62 L Labels bar code 6-4 guidelines for using 6-6 laser compliance xiv safety xiv LED, amber 7-12 LEDs 2-2, 7-7 LEDs, front panel 1-1 library configuration form G-1 library firmware, current level 5-33 library logs 5-59 library mode 4-24, 5-20, 5-33, 5-43 library name 5-43 library network configuration 4-30, 5-50 library recovery 7-7 library SNMP configuration 4-35, 5-56 library status 5-36 Library Verify 5-29 library weight 1-12 license act
Tape drives (continued) power management 1-11 quantity in library 1-9 speed matching 1-10 TapeAlert Flags for drives B-3 TapeAlert Flags, library B-1 technical support iii Telnet Service Port 5-32 Traps F-1 troubleshooting 7-1 U Ultra160 1-8 Ultra320 1-8 Ultrium Tape Drives 1-9 unpacking the library 4-2 Updating firmware using ITDT Tool 9-5 upgrade firmware 5-63 USB port 1-3 V verifying the shipment 4-2 View Drive Logs 5-60 W Web User Interface Configure Library: Event Notification 5-55 Configure Library
X-4 Dell PowerVault TL2000 Tape Library and TL4000 Tape Library User's Guide
Printed in USA