API Guide

ManualsBrandsDell ManualsAccess PlatformsPowerSwitch S5296F-ON

841

842

843

844

845

846

847

848

849

850

AG1(config)# interface ethernet 1/1/32:1

AG1(conf-if-eth1/1/32:1)# no shutdown

AG1(conf-if-eth1/1/32:1)# no switchport

AG1(conf-if-eth1/1/32:1)# ip address 16.0.0.1/24

AG1(conf-if-eth1/1/32:1)# flowcontrol receive off

AG1(conf-if-eth1/1/32:1)# ip pim sparse-mode

AG1(conf-if-eth1/1/32:1)# ip ospf 100 area 0.0.0.0

AG1(conf-if-eth1/1/32:1)# exit

AG1(config)# interface vlan 11

AG1(conf-if-vlan-11)# no shutdown

AG1(conf-if-vlan-11)# ip address 11.0.0.1/24

AG1(conf-if-vlan-11)# ip pim sparse-mode

AG1(conf-if-vlan-11)# ip pim dr-priority 1000

AG1(conf-if-vlan-11)# ip ospf 100 area 0.0.0.0

AG1(conf-if-vlan-11)# ip ospf cost 3000

AG1(conf-if-vlan-11)# exit

AG1(config)# interface vlan 12

AG1(conf-if-vlan-12)# no shutdown

AG1(conf-if-vlan-12)# ip address 12.0.0.1/24

AG1(conf-if-vlan-12)# ip pim sparse-mode

AG1(conf-if-vlan-12)# ip pim dr-priority 10

AG1(conf-if-vlan-12)# ip ospf 100 area 0.0.0.0

AG1(conf-if-vlan-12)# exit

AG1(config)# interface vlan 13

AG1(conf-if-vlan-13)# no shutdown

AG1(conf-if-vlan-13)# ip address 13.0.0.1/24

AG1(conf-if-vlan-13)# ip pim sparse-mode

AG1(conf-if-vlan-13)# ip pim dr-priority 10

AG1(conf-if-vlan-13)# ip ospf 100 area 0.0.0.0

AG1(conf-if-vlan-13)# ip ospf cost 4000

AG1(conf-if-vlan-13)# exit

AG1(config)# interface loopback 101

AG1(conf-if-lo-101)# no shutdown

AG1(conf-if-lo-101)# ip address 101.0.0.1/32

AG1(conf-if-lo-101)# ip pim sparse-mode

AG1(conf-if-lo-101)# ip ospf 100 area 0.0.0.0

AG1(conf-if-lo-101)# exit

AG1(config)# interface port-channel11

AG1(conf-if-po-11)# no shutdown

AG1(conf-if-po-11)# switchport mode trunk

AG1(conf-if-po-11)# switchport trunk allowed vlan 11

AG1(conf-if-po-11)# vlt-port-channel 11

AG1(conf-if-po-11)# exit

AG1(config)# interface port-channel12

AG1(conf-if-po-12)# no shutdown

AG1(conf-if-po-12)# switchport mode trunk

AG1(conf-if-po-12)# switchport access vlan 1

AG1(conf-if-po-12)# switchport trunk allowed vlan 12

AG1(conf-if-po-12)# vlt-port-channel 12

AG1(conf-if-po-12)# exit

PIM neighbors of AG1 and the interface to reach the neighbors

The show ip pim neighbor command displays the PIM neighbors of AG1 and the interface to reach the neighbors.

AG1# show ip pim neighbor

Neighbor Address Interface Uptime/Expires Ver DR Priority / Mode

----------------------------------------------------------------------

11.0.0.2 vlan11 00:00:43/00:01:33 v2 10 / S

12.0.0.2 vlan12 00:01:01/00:01:44 v2 10 / S

12.0.0.3 vlan12 00:01:01/00:01:43 v2 1000 / DR S

13.0.0.2 vlan13 00:01:02/00:01:42 v2 1000 / DR S

IGMP and PIM states in AG1

842

Multicast