Users Guide
Table Of Contents
- Dell EMC PowerEdge Servers Troubleshooting Guide
- Contents
- Introduction
- Diagnostic indicators
- Status LED indicators
- System health and system ID indicator codes
- iDRAC Quick Sync 2 indicator codes
- iDRAC Direct LED indicator codes
- NIC indicator codes
- Power supply unit indicator codes
- Non-redundant power supply unit indicator codes
- Hard drive indicator codes
- uSATA SSD indicator codes
- Internal dual SD module indicator codes
- Running diagnostics
- Troubleshooting hardware issues
- Troubleshooting system startup failure
- Troubleshooting external connections
- Troubleshooting the video subsystem
- Troubleshooting a USB device
- Troubleshooting a serial Input Output device
- Troubleshooting a NIC
- Troubleshooting a wet system
- Troubleshooting a damaged system
- Troubleshooting the system battery
- Troubleshooting cooling problems
- Troubleshooting cooling fans
- Troubleshooting an internal USB key
- Troubleshooting a micro SD card
- Troubleshooting expansion cards
- Troubleshooting processors
- Troubleshooting a storage controller
- OMSA flagging PERC driver
- Importing or clearing foreign configurations using the foreign configuration view screen
- Importing or clearing foreign configurations using the VD mgmt menu
- RAID controller L1, L2 and L3 cache error
- PERC controllers do not support NVME PCIe drives
- 12 Gbps hard drive does not support in SAS 6ir RAID controllers
- Hard drives cannot be added to the existing RAID 10 Array
- PERC battery discharging
- PERC battery failure message is displayed in ESM log
- Creating non-raid disks for storage purpose
- Firmware or Physical disks out-of-date
- Cannot boot to Windows due to foreign configuration
- Offline or missing virtual drives with preserved cache error message
- Expanding RAID array
- LTO-4 Tape drives are not supported on PERC
- Limitations of HDD size on H310
- System logs show failure entry for a storage controller even though it is working correctly
- Troubleshooting hard drives
- Troubleshooting an optical drive
- Troubleshooting a tape backup unit
- Troubleshooting no power issues
- Troubleshooting power supply units
- Troubleshooting RAID
- RAID configuration using PERC
- RAID configuration using OpenManage Server Administrator
- RAID configuration by using Unified Server Configurator
- Downloading and installing the RAID controller log export by using PERCCLI tool on ESXi hosts on Dell’s 13th generation of PowerEdge servers
- Configuring RAID by using Lifecycle Controller
- Starting and target RAID levels for virtual disk reconfiguration and capacity expansion
- Replacing physical disks in RAID1 configuration
- Thumb rules for RAID configuration
- Reconfiguring or migrating virtual disks
- Foreign Configuration Operations
- Viewing Patrol Read report
- Check Consistency report
- Virtual disk troubleshooting
- Rebuilding of virtual disk does not work
- Rebuilding of virtual disk completes with errors
- Cannot create a virtual disk
- A virtual disk of minimum size is not visible to Windows Disk Management
- Virtual disk errors on systems running Linux
- Problems associated with using the same physical disks for both redundant and nonredundant virtual disks
- Enable the alarm on PERC 5/E adapter to alert in case of physical disk failures
- RAID controller displays multibit ECC errors
- PERC goes offline with an error message
- Reconfiguring the RAID level and virtual disks
- Lost shared storage access
- Troubleshooting memory or battery errors on the PERC controller on Dell PowerEdge servers
- Slicing
- RAID puncture
- Troubleshooting thermal issue
- Input/Output errors while reseating SAS IOM storage sled on hardware configurations
- Server management software issues
- What are the different types of iDRAC licenses
- How to activate license on iDRAC
- Can I upgrade the iDRAC license from express to enterprise and BMC to express
- How to find out missing licenses
- How to export license using iDRAC web interface
- How to set up e-mail alerts
- System time zone is not synchronized
- How to set up Auto Dedicated NIC feature
- How to configure network settings using Lifecycle Controller
- Assigning hot spare with OMSA
- Storage Health
- How do I configure RAID using operating system deployment wizard
- Foreign drivers on physical disk
- Physical disk reported as Foreign
- How to update BIOS on 13th generation PowerEdge servers
- Why am I unable to update firmware
- Which are the operating systems supported on Dell EMC PowerEdge servers
- Unable to create a partition or locate the partition and unable to install Microsoft Windows Server 2012
- JAVA support in iDRAC
- How to specify language and keyboard type
- Message Event ID - 2405
- Installing Managed System Software On Microsoft Windows Operating Systems
- Installing Managed System Software On Microsoft Windows Server and Microsoft Hyper-V Server
- Installing Systems Management Software On VMware ESXi
- Processor TEMP error
- PowerEdge T130, R230, R330, and T330 servers may report a critical error during scheduled warm reboots
- SSD is not detected
- OpenManage Essentials does not recognize the server
- Unable to connect to iDRAC port through a switch
- Lifecycle Controller is not recognizing USB in UEFI mode
- Guidance on remote desktop services
- Troubleshooting operating system issues
- How to install the operating system on a Dell PowerEdge Server
- Locating the VMware and Windows licensing
- Troubleshooting blue screen errors or BSODs
- Troubleshooting a Purple Screen of Death or PSOD
- Troubleshooting no boot issues for Windows operating systems
- No POST issues in iDRAC
- Troubleshooting a No POST situation
- Migrating to OneDrive for Business using Dell Migration Suite for SharePoint
- Windows
- Installing and reinstalling Microsoft Windows Server 2016
- FAQs
- Why are the USB keyboard and mouse not detected during the Windows Server 2008 R2 SP1 installation
- Why does the installation wizard stop responding during the Windows OS installation
- Why does Windows OS installation using Lifecycle Controller, on PowerEdge Servers fail at times with an error message
- Why does Windows Server 2008 R2 SP1 display a blank screen in UEFI mode after installation
- Symptoms
- Troubleshooting system crash at cng.sys with watchdog Error violation
- Host bus adapter mini is missing physical disks and backplane in Windows
- Converting evaluation OS version to retail OS version
- Partitions on disk selected for installation of Hyper-V server 2012
- Install Microsoft Hyper-V Server 2012 R2 with the Internal Dual SD module
- VMware
- Linux
- Installing operating system through various methods
- Getting help
Table 13. PSA/ePSA error codes (continued)
Error number (PSA and
ePSA)
Error message Description Steps
3. If failure continues,
contact Technical Support
PSA 1000-0321
ePSA 2000-0321
PSA LCD EDID - unable to
access EDID EEPROM
ePSA Unable to detect LCD
LCD Extended Display
Identification Data (EDID)
- unable to access the
EDID Electrically Erasable
Programmable Read-Only
Memory (EEPROM) in the
LCD display is indicating a
data failure. If there is video
on the LCD, then the Display
does not need replacement.
1. Update to the latest BIOS
version.
2. Turn off your computer
and reconnect your LCD
cable.
3. Repeat the PSA
diagnostics..
4. If failure continues,
contact Dell Technical
Support
PSA 1000-0322
ePSA 2000-0322
PSA LCD Panel - Error
accessing the LCD inverter
ePSA LCD panel - unable to
modify brightness
LCD panel - unable to modify
brightness. Try to adjust the
brightness in Windows using
the hotkeys. Boot to the BIOS
and see if brightness can be
adjusted at that point outside
of Windows
1. Update to the latest BIOS
version.
2. Turn off your computer
and reconnect your LCD
cable.
3. Repeat the PSA
diagnostics.
4. If failure continues,
contact Dell Technical
Support
PSA NA
ePSA 2000-0323
LCD panel - Unable to detect
inverter lamp status.
Check LCD connector and
cables.
1. Update to the latest BIOS
version.
2. Repeat the PSA
diagnostics.
3. If failure continues,
contact Dell Technical
Support
PSA NA
ePSA 2000-0324
LCD panel - user reported
LCD BIST colors were not
displayed
You may get this error if
you answered No to the LCD
BIST test instead of Yes.
If you were able to clearly
see red, blue, green white
and white screen with text
without distortion, lines, or
color problems, re-run the
diagnostic and if the screens
appear normal, click Yes
1. Update to the latest BIOS
version.
2. Turn off your computer
and reconnect your LCD
cable.
3. Repeat the LCD BIST
diagnostics.
4. If failure continues,
contact Dell Technical
Support
PSA NA
ePSA 2000-0325
LCD panel - user provided no
input for LCD BIST
You may get this error if
you answered No to the LCD
BIST test instead of Yes.
If you were able to clearly
see red, blue, green white
and white screen with text
without distortion, lines, or
color problems, re-run the
diagnostic and if the screens
appear normal, click Yes
1. Update to the latest BIOS
version.
2. Turn off your computer
and reconnect your LCD
cable.
3. Repeat the PSA
diagnostics.
4. If failure continues,
contact Technical Support
PSA 1000-0326
ePSA 2000-0326
LCD panel - unable to turn
lamp on or off
The backlight lamp was not
able to be turned on or off
during the diagnostic testing
1. Update to the latest BIOS.
2. Turn off your computer
and reconnect your LCD
cable.
28 Running diagnostics