Users Guide
Table Of Contents
- Dell™ PowerEdge™ 2970
- Information Update
- Contents
- Non-Optimal Memory Configurations
- Regional Hardware Owner’s Manuals Available on the Web
- Using the Online Diagnostics
- System Setup Program Updates
- System Start-up Behavior
- Overcurrent Events on USB Ports
- LCD Status Message Update
- System Board Jumpers
- Creating a BMC User Password
- System Memory Update
- 3.5-Inch Chassis Update
- 信息更新
- Mise à jour des informations
- Table des matières
- Configurations de mémoire non optimales
- Versions régionales du Manuel du propriétaire disponibles sur le Web
- Utilisation des diagnostics en ligne
- Mises à jour apportées au programme de configuration du système
- Comportement du système au démarrage
- Surtensions sur les ports USB
- Mise à jour des message d'état affichés sur l'écran LCD
- Cavaliers de la carte système
- Création d'un mot de passe BMC
- Mise à jour de la mémoire système
- Mise à jour concernant le châssis 3,5 pouces
- Voyants et fonctions du panneau avant
- Configuration mixte de disques durs SAS/SATA (disques 3,5 pouces uniquement)
- Retrait d'un cache de lecteur 3,5 pouces
- Installation d'un cache de lecteur 3,5 pouces
- Retrait de la carte de fond de panier SAS/SATA
- Installation de la carte de fond de panier SAS
- Connecteurs de la carte de fond de panier SAS/SATA
- Informationsaktualisierung
- Inhalt
- Nicht-optimale Speicherkonfigurationen
- Regionale Hardware-Benutzerhandbücher im Web bereitgestellt
- Verwenden der Online-Diagnose
- Ergänzende Informationen zum System-Setup- Programm
- Systemverhalten beim Start
- Überstromereignisse an USB-Ports
- Update zu LCD-Statusmeldungen
- Jumper auf der Systemplatine
- Erstellen eines BMC-Benutzerkennworts
- Update zum Systemspeicher
- Update zum 3,5-Zoll-Gehäuse
- Funktionsmerkmale und Anzeigen auf der Vorderseite
- Gemischte SAS/SATA-Festplattenkonfiguration (nur 3,5-Zoll-Laufwerke)
- Entfernen eines 3,5-Zoll-Laufwerkplatzhalters
- Installieren eines 3,5-Zoll-Laufwerkplatzhalters
- Entfernen der SAS/SATA-Rückwandplatine
- Installieren der SAS-Rückwandplatine
- Anschlüsse der SAS/SATA-Rückwandplatine
- アップデート情報
- 정보 갱신본
- Actualización de información
- Contenido
- Configuraciones de memoria no óptimas
- Manual del propietario del hardware específico para cada región disponible en Internet
- Uso de los diagnósticos en línea
- Actualizaciones del programa de configuración del sistema
- Comportamiento de inicio del sistema
- Sobrecorrientes en puertos USB
- Actualización de los mensajes de estado de la pantalla LCD
- Puentes de la placa base
- Creación de una contraseña de usuario para la BMC
- Actualización de la memoria del sistema
- Actualización del chasis de 3,5 pulgadas
- Componentes e indicadores de la parte frontal
- Configuración combinada de unidades de disco duro SAS/SATA (sólo unidades de 3,5 pulgadas)
- Extracción de una unidad de relleno de 3,5 pulgadas
- Instalación de una unidad de relleno de 3,5 pulgadas
- Extracción de la placa de plano posterior SAS/SATA
- Instalación de la placa de plano posterior SAS
- Conectores de la placa de plano posterior SAS/SATA
- Information Update
Information Update 7
Default Settings Update
The following bullets are updates to information listed in your Hardware
Owner’s Manual.
•On the
Serial Communication
screen, the default setting for the
Serial
Communication
field is
On without Console Redirection
.
•On the
Serial Communication
screen, the default setting for the
Failsafe
Baud Rate
field is
115200
.
System Start-up Behavior
Note the following events that may occur on your system during start-up.
• On systems with large memory configurations, the video monitor can take
from several seconds to approximately two minutes to display an image
at startup.
• If you are running the Red Hat Enterprise Linux WS, ES, or AS
(Version 4) (x86-64) operating system, the system may display the
following on-screen message several times during start-up:
clear kernel mapping: mapping is split: will leak
memory
This message is specific to the operating system and does not indicate
a problem with your system hardware.
Overcurrent Events on USB Ports
Some USB devices can cause an overcurrent event on your system’s USB
ports. When this occurs, the system disables one or more of the affected USB
ports, and communication with the attached USB devices is lost. An on-
screen system message may appear noting the event, but this is not always
the case, particularly with devices connected to the rear USB ports. If an
overcurrent event disables your system’s USB ports, re-enable the ports by
restarting your system.
If overcurrent events persist, you may need to remove or replace the USB
device(s) connected to your system.