Dell PowerEdge M1000e Enclosure Owner's Manual Regulatory Model: BMX01 October 2019 Rev.
Notes, cautions, and warnings NOTE: A NOTE indicates important information that helps you make better use of your product. CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. WARNING: A WARNING indicates a potential for property damage, personal injury, or death. © 2014 – 2019 Dell Inc. or its subsidiaries. All rights reserved. Dell, EMC, and other trademarks are trademarks of Dell Inc. or its subsidiaries.
Contents Chapter 1: About your system........................................................................................................6 System Overview.................................................................................................................................................................6 System Control-Panel Features....................................................................................................................................... 8 LCD Module..............
FlexAddress Plus................................................................................................................................................................33 Chapter 3: Configuring The I/O Modules..................................................................................... 34 Network Information........................................................................................................................................................ 34 I/O Connectivity...............
Installing A Blade..........................................................................................................................................................68 Power Supply Modules.................................................................................................................................................... 68 Power Supply Blanks..................................................................................................................................................
1 About your system Topics: • • • • • • • • • System Overview System Control-Panel Features LCD Module Configuration Wizard Back-Panel Features Avocent iKVM Analog Switch Module (Optional) CMC Module System Messages Documentation Matrix System Overview Your system can include up to 16 half-height blades (server modules), eight full-height blades, eight sleeves with quarter-height blades, or a mix of the three blade types.
Figure 2. Blade Numbering – Full Height Blades Figure 3.
Figure 4. Blade Numbering – Mixed Full-Height, Half-Height, and Quarter-Height Blades System Control-Panel Features Figure 5. Control-Panel Features 1. USB port (mouse only) 3. video connector 5. system power indicator 8 About your system 2. USB port (keyboard only) 4.
Control Panel Features USB ports for keyboard and mouse Description Icon Description USB port 1 connects to the mouse and USB port 2 connects to the keyboard. NOTE: The USB ports are functional if an optional iKVM module is installed and front panel ports are enabled (default setting) in the CMC interface. NOTE: These ports do not support USB storage devices. Only connect USB storage devices to the USB ports on the front panel of the blade.
Figure 6. LCD Display 1. LCD screen 2. scroll buttons (4) 3. selection ("check") button LCD Module Features The primary function of the LCD module is to provide real-time information on the health and status of the modules in the enclosure. LCD module features include: ● ● ● ● ● ● ● ● ● A deployment setup wizard that allows you to configure the CMC module’s network settings during initial system set up. Menus to configure the iDRAC in each blade. Status information screens for each blade.
Main Menu The Main Menu options include links to the LCD Setup Menu, Server Menu, and Enclosure Menu. LCD Setup Menu You can change the default language and start-up screen for the LCD menu screens using this menu. Server Menu From the Server Menu dialog box, you can highlight each blade in the enclosure using the arrow keys, and view its status. ● A blade that is turned off or booting is designated by a gray rectangle. An active blade is indicated by a green rectangle.
NOTE: The configuration wizard automatically configures each blade’s iDRAC internal network interface if you do not choose to manually configure the iDRAC settings. NOTE: You cannot set a static IP address for the iDRAC using the LCD configuration wizard. To set a static IP address, use the CMC web-based interface or Remote Access Controller Administrator (RACADM). 6.
Figure 8. Back-Panel Module Bay Numbering 1. CMC 1 (primary CMC module) 3. iKVM (iKVM module) 5. CMC 2 (secondary CMC module) 2. A1 B1 C1 (left I/O modules) 4. C2 B2 A2 (right I/O modules) Power Supply Indicators NOTE: The AC power supplies must be connected to a Power Distribution Unit (PDU), not directly to an electrical outlet. For DC power supplies, plug the other end of the power cables to a branch circuit-protective ground DC power source of – (48–60) V DC.
Figure 9. Power Supply Indicators 1. DC power output indicator 2. power supply fault indicator 3. AC power indicator The power supply indicators provide the following information: Indicator DC power output indicator Description Icon Description Power supply fault indicator Icon Description AC power source present indicator Amber indicates a problem with the power supply, which can result from either a failed power supply or a failed fan within the power supply.
Fan Module Indicators Figure 10. Fan Module Indicators 1. fan power indicator 2. fan fault indicator The indicators provide the following information: Indicator Description Fan power indicator Solid Green The fan is receiving DC power and working properly. Off The fan has failed. Amber The fan is in a fault condition.
Avocent iKVM Analog Switch Module (Optional) Figure 11. Avocent iKVM Switch Module 2. power indicator 1. status/identification indicator 3. link indicator 4. Analog Console Interface (ACI) port (for tiering connection only) CAUTION: Do not connect the ACI port to a LAN device such as a network hub. Doing so may result in equipment damage. 5. activity indicator 7. video connector 6.
Module Indicator Activity indicator Description Green The ACI is connected to the external switch. Off Data is not being sent or received. Amber blinking Data is being sent or received. Avocent Analog iKVM Switch Module Features ● Local iKVM access can be remotely disabled on a per blade basis, using the blade’s iDRAC interface (access is enabled by default). NOTE: A console session (enabled by default) to a given blade is available for both iDRAC interface and iKVM users.
CMC Module Figure 12. CMC Module Features 1. Ethernet connector Gb1 3. 5. 7. 9. Link indicator DB-9 serial connector for local configuration Optional iKVM module Blue status/identification indicator 2. Ethernet connector STK ("stack") - used for daisy-chaining CMCs in separate enclosures 4. Activity indicator 6. Optional secondary CMC (CMC 2) 8. Primary CMC (CMC 1) 10.
○ Checks I/O fabric consistency between the I/O modules and blades and disables components if necessary to protect the system hardware ○ User access security NOTE: It is recommended that you isolate chassis management from the data network. Dell cannot support or guarantee uptime of a chassis that is improperly integrated into your environment. Due to the potential of traffic on the data network, the management interfaces on the internal management network can be saturated by traffic intended for servers.
of management network connections required from eight to two. If each chassis has only one CMC, you can reduce the connections required from four to one. When daisy-chaining chassis together, GB is the uplink port and STK is the stacking (cable consolidation) port. Connect the GB ports to the management network or to the STK port of the CMC in a chassis that is closer to the network. You must connect the STK port only to a GB port further from the chain or network.
Documentation Matrix The documentation matrix provides information about documents that you can refer to, for setting up and managing your system. Table 1. Documentation Matrix To... Refer to... Install your system into a rack Rack documentation included with your rack solution Set up your system and know the system technical specifications Getting Started Guide Install the operating system Operating system documentation at dell.
Figure 14.
2 Initial system configuration Topics: • • • • • • • • • • • • Before You Begin Initial Setup Sequence Initial CMC Network Configuration Logging In To The CMC Using The Web-Based Interface Adding And Managing CMC Users Configuring iDRAC Networking Using The Web-Based Interface Setting The First Boot Device For Servers Configuring And Managing Power Installing Or Updating The CMC Firmware Configuring The Optional iKVM Switch Module FlexAddress FlexAddress Plus Before You Begin CAUTION: The enclosure power
6. Configure the I/O modules to allow proper network or storage management or paths. 7. After the Ethernet and fibre channel switches are configured, you can turn on your server blades. This allows time for the Ethernet switch to boot and allow PXI\UNDI traffic for all blade modules. Initial CMC Network Configuration Prerequisites The CMC is preset for DHCP.
NOTE: If you want to use static addresses rather than DHCP to access the iDRACs, you must configure them using the CMC web-based interface or CLI. Configuring The CMC Using A Management Station And CLI The LCD configuration wizard is the quickest way to initially configure the CMC network settings. However, you can also use a management station and a local connection to access the CMC. About this task There are two ways to create a local connection to the CMC: ● The CMC Console, using the optional iKVM.
The CMC Login page is displayed. NOTE: The default CMC user name is root, and the password is calvin. The root account is the default administrative account that ships with the CMC. For added security, you must change the default password of the root account during initial setup. NOTE: The CMC does not support extended ASCII characters, such as ß, å, é, ü, or other characters used primarily in non-English languages.
Configuring iDRAC Networking Using The Web-Based Interface About this task Follow this procedure to configure the iDRAC in the LCD configuration wizard. NOTE: If you did not configure the iDRAC using the LCD configuration wizard, iDRAC is disabled until you configure it using the web-based interface. NOTE: You must have Chassis Configuration Administrator privileges to set up iDRAC network settings from the CMC. NOTE: The default CMC user name is root and the default password is calvin. Steps 1.
Configuring And Managing Power You can use the web-based and RACADM interfaces to manage and configure power controls on the CMC, as outlined in the following sections. For more information on the various power management options, see the CMC User’s Guide at support.dell.com/manuals. About this task The CMC’s power management service optimizes power consumption for the entire chassis (the chassis, servers, I/O modules, iKVM, CMC, and PSUs) and re-allocates power to different modules based on the demand.
Use the Firmware Update page to update the CMC firmware to the latest revision. When you run the firmware update, the update retains the current CMC settings. The following is the link to the M1000e downloads page:https://www.dell.com/ support/home/us/en/19/product-support/product/poweredge-m1000e/drivers NOTE: The firmware update, by default, retains the current CMC settings. During the update process, you have the option to reset the CMC configuration settings back to the factory default settings.
5. In the Value field, type the path on your management station or shared network where the firmware image file resides, or click Browse to navigate to the file location. NOTE: The default iKVM firmware image name is ikvm.bin. However, the iKVM firmware image name can be renamed. If you are unable to locate ikvm.bin, verify if another user has renamed the file. 6. Click Update. A dialog box prompts you to confirm the action. 7. Click Yes to continue. Next steps When the update is complete, the iKVM resets.
NOTE: Soft switching allows you to switch servers using a hot key sequence. To soft switch to a server, press and type the first few characters of its name or number. If you have a Delay Time set and you press the key sequences before that time has elapsed, OSCAR does not display. Configuring The Analog Switch Steps 1. Press to launch the iKVM Switch OSCAR. 2. Click Setup > Devices > Device Modify. 3. Select the 16-port option to match the number of blades in your system. 4.
5. Click Next to update the database. If a cascade switch was detected, the Enter Cascade Switch Information dialog box is displayed. 6. Select the type of switch connected to the appliance from the drop-down list. If the type you are looking for is not available, you can add it by clicking Add. 7. Click Next. The completion dialog box is displayed. 8. Click Finish to exit. 9. Start up the analog switch and the system.
For example: (starting_mac)00188BFFDCFA + 0xCF = (ending_mac)00188BFFDDC9 NOTE: To prevent modifying any of the contents accidentally, you must lock the SD card prior to inserting in the USB "Memory Card Reader". You must then unlock the SD card before inserting it into the CMC. For more information on the FlexAddress feature, see the following resources: ● The CMC Secure Digital (SD) Card Technical Specification document at support.dell.
3 Configuring The I/O Modules Topics: • • • • • • • • Network Information I/O Connectivity Port Auto-Disablement in Quad-Port Network Daughter Card (Dell PowerEdge M710HD Only) Mezzanine Cards I/O Module Port Mapping—Full-Height Blades I/O Module Port Mapping─Half-Height Blades I/O Modules—Switches I/O Modules—Pass-Through Network Information You can configure your I/O switch modules using: ● CMC web-based interface. NOTE: The default IP address for the CMC is 192.168.0.120.
NOTE: Modules designed specifically for Fabric B or Fabric C cannot be installed in slots A1 or A2, as indicated by the colorcoded labeling on the faceplate of each module. Fabric B Fabric B is a 1 to 40 Gb/sec redundant fabric, supporting I/O module slots B1 and B2. Fabric B currently supports 1 Gb or 10 Gb Ethernet, DDR/QDR Infiniband, and 4 Gbps or 8 Gbps fibre channel modules. Additional fabric types may be supported in the future.
Table 2. Port Auto-Disablement Decision Table (continued) IOM Slot A1 IOM Slot A2 NIC3 and NIC4 (Enabled/ Disabled) Port Auto-Disablement Quad or Greater Port Quad or Greater Port Enabled Inactive Mezzanine Cards PowerEdge M610x Only PowerEdge M610x supports two mezzanine cards. Mezzanine cards can be installed in both the slots on the midplane interface card. NOTE: PowerEdge M610x is a full-height blade but supports only two mezzanine cards in the expansion bay.
Table 3.
● Mezzanine card 4, connection 1 connects to I/O module B1, port n+8. Mezzanine card 4, connection 2 connects to I/O module B2 port n+8. For example, in a full-height blade: ● Mezzanine card 3 connection 1 connects to I/O module C1, port 13. ● Mezzanine card 3 connection 2 connects to I/O module C2 port 13. The following table shows the port number assignments for the eight possible full height blade locations.
Table 5. I/O Module Port Assignments - Full-Height Blades (not applicable for PowerEdge M610x) Blade 1 I/O Module B1 Mezz1_Fab_C Mezz2_Fab_B C2 B2 Port 1 Port 1 Port 1 Mezz3_Fab_C Mezz4_Fab_B C1 Port 1 Port 9 Port 9 Port 9 Port 9 Table 6. I/O Module Port Assignments - Full-Height Blades (not applicable for PowerEdge M610x) Blade 2 I/O Module B1 Mezz1_Fab_C Mezz2_Fab_B C2 B2 Port 2 Port 2 Port 2 Mezz3_Fab_C Mezz4_Fab_B C1 Port 2 Port 10 Port 10 Port 10 Port 10 Table 7.
Table 10. I/O Module Port Assignments - Full-Height Blades (not applicable for PowerEdge M610x) (continued) Blade 6 I/O Module B1 Mezz2_Fab_B C2 Port 6 Mezz3_Fab_C Mezz4_Fab_B C1 B2 Port 6 Port 14 Port 14 Port 14 Port 14 Table 11. I/O Module Port Assignments - Full-Height Blades (not applicable for PowerEdge M610x) Blade 7 I/O Module B1 Mezz1_Fab_C Mezz2_Fab_B C2 Port 7 Port 7 Port 7 Mezz3_Fab_C Mezz4_Fab_B C1 B2 Port 7 Port 15 Port 15 Port 15 Port 15 Table 12.
Figure 16. Example of Full-Height Blade Port Mapping – Blade 3 (not applicable for PowerEdge M610x) Quad-Port Mezzanine Cards The following table illustrates the I/O module port mapping for full-height blades with quad-port mezzanine cards. NOTE: For a detailed mapping of each PowerEdge system, see Quadport Capable Hardware for the M1000e Modular Chassis at support.dell.com/manuals. Table 13.
Table 13. Example of I/O Module Port Assignments - PowerEdge M610x in Slot 2 (continued) Blade n and Blade (n + 8) NOTE: n denotes a variable value from 1 to 8.
I/O Module Port Mapping─Half-Height Blades Standard LOM (Dual-Port) and Network Daughter Card (QuadPort) Mapping Each standard LOM has two port connections. For a half-height blade in bay n: Integrated LOM, connection 1 connects to I/O module A1, port n. Integrated LOM, connection 2 connects to I/O module A2, port n. Half-height blades with network daughter card (M710HD) hosts two network controllers (LOM1 and LOM2), each with two port connections.
Figure 17. Example of Half-Height Blade Port Mapping Quad-Port Mezzanine Cards The following table illustrates the I/O module port mapping for a half-height blade with the quad-port mezzanine card. In the following table, n denotes a variable value from 1 to 16. NOTE: For a detailed mapping of each PowerEdge system, see Quadport Capable Hardware For the M1000e Modular Chassis at support.dell.com/manuals. Table 16.
Table 16. Example of I/O Module Port Assignments - PowerEdge M610x in Slot 2 (continued) Blade n Mezz_FAB_C_Blade n_Port1 I/O Module Port n Mezz_FAB_C_Blade n_Port2 Mezz_FAB_C_Blade n_Port3 Port n Port (n+16) Mezz_FAB_C_Blade n_Port4 Port (n+16) I/O Modules—Switches Configuring A Switch Module Network Ethernet Port Using The Web-Based Interface You can use the CMC web-based interface to configure an I/O module’s Ethernet port.
Brocade M6505 16 Gbps FC SAN I/O Module The Brocade M6505 16 Gbps FC I/O module includes eight external fibre channel ports, 16 internal ports, and one serial port with an RJ-45 connector. The external fibre channel ports operate at 4 Gbps, 8 Gbps, or 16 Gbps. Internal ports support speeds of 8 Gbps and 16 Gbps. NOTE: This module can be upgraded to 24 ports using a Ports on Demand (POD) license.
Figure 19. Cisco Nexus B22 Fabric Extender Module 1. 2. 3. 4. external network ports (8) port LED indicator status indicator identification indicator Dell PowerEdge M I/O Aggregator Switch The PowerEdge I/O Aggregator is a layer 2 switch blade with two fixed 40 GbE ports on the base module and provides support for two optional plug-in modules. The Aggregator runs the Dell Force10 Operating System (FTOS) and autoconfigures as an unmanaged switch with bridging and multiplexing features.
Figure 20. Dell PowerEdge M I/O Aggregator Switch 1. expansion slot 1 3. USB storage port 5. USB console port 2. expansion slot 0 4. activity and link LEDs 6. 40 GbE QSFP+ ports Dell Force10 MXL 10/40 GbE Switch The Force10 MXL 10/40 GbE switch module has two fixed 40 GbE ports on the base module and provides support for two optional plug-in modules. This module provides: ● Thirty two 1 GbE or 10 GbE internal ports — each port can operate in either 1 GbE or 10 GbE mode.
Figure 21. Dell Force10 MXL 10/40 GbE Switch I/O Module 1. 3. 5. 7. expansion slots (8) USB storage port status/identification indicator 40 GbE QSFP+ ports (2) 2. LED status indicators 4. USB console port 6. power indicator Mellanox M4001F/M4001Q/M4001T Infiniband Switch I/O Module The Mellanox M4001F/M4001Q/M4001T Infiniband switch delivers 56 Gb/s at FDR speed and 40 Gb/s at QDR and FDR10 speed (full bisectional bandwidth per port).
Figure 22. Mellanox M4001F/M4001Q/M4001T Infiniband Switch Module 1. Infiniband QSFP ports (16) 3. serial port (RJ-45 connector) 5. power indicator 2. LED status/module status indicators 4. module status indicator Dell PowerConnect KR 8024-k Switch The PowerConnect KR M8024-k switch provides 16 internal 10 GbE ports, four external 10 GbE SFP+ ports, and one 10 GbE expansion slot for 10 GbE external uplinks.
Figure 23. Dell PowerConnect KR 8024-k Switch 1. SFP+ ports (4) 3. status/identification indicator 5. expansion slot 2. console management connector 4. power indicator Dell PowerConnect M8428-k 10 Gb Converged Network Switch The Dell PowerConnect M8428-k 10 Gb Converged Network switch module supports FCoE protocols and allows fibre channel traffic to travel over 10 Gbps Enhanced Ethernet (DCB) networks. This module consists of: ● ● ● ● Four 8 Gbps external autosensing fibre channel ports.
Figure 24. Dell PowerConnect M8428-k 10 Gb Converged Network Switch 1. 3. 5. 7. LED status indicators (12) module status indicator power indicator 10 GbE ports (ports 17–24) 2. serial port (RJ-45 connector) 4. diagnostic status indicator 6. 8 Gb fibre channel ports (ports 25–27 and port 0) Mellanox M2401G DDR Infiniband Switch I/O Module The Mellanox M2401G DDR Infiniband switch I/O module includes 24 4x DDR Infiniband ports.
Figure 25. Mellanox M2401G DDR Infiniband Switch Module 1. Infiniband ports (8) 3. port activity indicators (8) 5. module status indicator 2. port link status indicators (8) 4. module diagnostic power indicator Mellanox M3601Q QDR Infiniband Switch I/O Module The Mellanox M3601Q QDR Infiniband switch I/O module includes 32 4x QDR Infiniband ports. Of these, 16 ports are external uplink ports, while 16 internal ports provide connectivity to the blades in the enclosure.
Figure 26. Mellanox M3601Q QDR Infiniband Switch I/O Module 1. Infiniband ports (16) 3. port activity indicators (16) 5. module status indicator 2. port link status indicators (16) 4. module diagnostic power indicator Cisco Catalyst Ethernet Switch I/O Modules Your system supports three Cisco Catalyst Blade Switch (CBS) versions: ● The Cisco 3130G-S switch includes four 10/100/1000 Mb Ethernet uplink ports and two Stackwise Plus ports.
Figure 27. Cisco Catalyst Ethernet Switch Module Features 1. 3. 5. 7. Stackwise Plus connectors (not enabled in CBS 3032) option bays (2) mode button power indicator 2. 4. 6. 8. 10/100/1000 Mb Ethernet connectors (4) Cisco status indicators console port for switch management status/identification indicator Dell PowerConnect M6348 1 Gb Ethernet Switch I/O Module PowerConnect M6348 is a hot-swappable 48-port 1 Gb Ethernet switch.
Figure 28. PowerConnect M6348 1 Gb Ethernet Switch I/O Module Features 1. standard 10/100/1000 Mb Ethernet connectors (16) 3. CX4 stacking connectors (2) 5. power indicator 2. SFP+ connectors (2) 4. console management connector 6. status/identification indicator Dell PowerConnect M6220 Ethernet Switch I/O Module The PowerConnect M6220 Ethernet switch module includes four external 10/100/1000 Mbps Ethernet connectors and one USB type A form factor serial connector.
Figure 29. PowerConnect M6220 Ethernet Switch I/O Module 1. optional modules (2) (dual 10 Gb Ethernet uplink module shown) 3. serial connector (USB type-A form factor) 5. status/identification indicator 2. standard 10/100/1000 Mb Ethernet connectors (4) 4.
Figure 30. PowerConnect M8024 10 Gb Ethernet Switch I/O Module 2. optional module with three CX4 ports 1. optional module with four SFP+ ports 3. serial connector for optional USB type-A form-factor cable 4. power indicator 5.
Figure 31. Dell 8/4 Gbps FC SAN Module 1. 3. 5. 7. fibre channel ports (8) fibre channel port speed indicators (8) module status indicator status/identification indicator 2. fibre channel port status indicators (8) 4. serial port (RJ-45 connector) 6.
Figure 32. Brocade M5424 FC8 I/O Module 1. 3. 5. 7. fibre channel ports (8) fibre channel port speed indicators (8) module status indicator status/identification indicator 2. fibre channel port status indicators (8) 4. serial port (RJ-45 connector) 6.
Module status indicator Module power indicator Status/ identification indicator Indicator Status Off Module is off or enclosure power is off Green on All ports are ready for use Amber on Module is booting, being reset, or ports are offline Green/amber blinking Diagnostic message is in error log, or environmental range is exceeded Indicator Status Off Power to the module is off Green Module has power Indicator Status Blue on Normal health Blue off Boot in progress Blue blinking Iden
Figure 33. 4 Gbps Fibre Channel Pass-Through Module 1. SFP fibre channel connectors (16) 3. power indicator 2. fibre channel green/amber indicators (two per port) 4. status/identification indicator The following are the fibre channel pass-through indicators: 1. Power Indicator: ● Off: Power to the module is off ● Green: Module has power 1.
9. Off/amber flashing (twice per second): Connection has lost synchronization Dell 10 GbE KR Pass-Through I/O Module The 10 GbE KR pass-through module supports 10 Gb connections and provides a direct connection between the optional internal Ethernet KR mezzanine card or KR network daughter card in the blade and an external Ethernet device. This module has 16 external SFP+ ports on the front panel and sixteen 10 GbE KR internal ports through the backplane.
Figure 35. 10 Gb Ethernet Pass-Through Module II 1. SFP+ ports (16) 3. status/identification indicator 2. green/amber indicators (two per port) 4. power indicator 10/100/1000 Mb Ethernet Pass-Through I/O Module The Ethernet pass-through module supports 10/100/1000 Mb connections and provides a direct connection between the optional internal Ethernet mezzanine card in the blade and an external Ethernet device.
Figure 36. 10/100/1000 Mb Ethernet Pass-Through I/O Module 1. activity indicators (16) 3. RJ-45 Ethernet connectors (16) 5. status/identification indicator 2. link indicators (16) 4. power indicator NOTE: Connectors on the Ethernet pass-through module correspond directly to the blade number. For example, blade 5 is connected to port 5 on the Ethernet pass-through module. Integrated network adapter 1 maps to I/O slot A1. Integrated network adapter 2 maps to I/O slot A2.
4 Installing Enclosure Components NOTE: To ensure proper operation and cooling, all bays in the enclosure must be populated at all times with either a module or with a blank.
NOTE: A full-height blade requires two blade blanks. 4. Slide the blade out of the enclosure. CAUTION: To protect the I/O connector pins, install the I/O connector covers any time a blade is removed from the enclosure. NOTE: A full-height blade requires four connector covers and a half-height blade requires two connector covers. 5. Install the I/O connector cover over the I/O connector. Figure 37. Removing and Installing a Half-Height Blade 1. blade handle 3. blade 5.
Figure 38. Removing and Installing a Full-Height Blade 1. blade handle 3. blade 5. guide rail on blade (or blade blank) 2. release button 4. guide rail on enclosure Installing A Blade Steps 1. If you are installing a new blade, remove the plastic cover from the I/O connector(s) and save for future use. 2. Orient the blade so that the blade handle is on the left side of the blade.
Power Supply Blanks If the M1000e enclosure is operated with only three power supplies, power supply blanks must be installed in the three unoccupied power supply bays (4 through 6) to maintain proper cooling airflow in the enclosure. AC Power Supply Modules NOTE: A 2700 W power supply module requires 110 V to 240 V input from an AC power source.
Figure 39. Power Cable Retention Clip 1. power supply 3. notch in power supply handle 5. power cable 70 Installing Enclosure Components 2. retention clip tether 4.
Figure 40. Removing and Installing a Power Supply Module a. power supply b. handle c. release button Installing An AC Power Supply Prerequisites CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty.
NOTE: For equipment using –(48–60) V DC power supplies, a qualified electrician must perform all connections to DC power and to safety grounds. Do not attempt connecting to DC power or installing grounds yourself. All electrical wiring must comply with applicable local or national codes and practices. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow all safety instructions that came with the product.
Kit Contents ● Molex # 394260002 at PSU end ● Molex # 39422-0012 mating DC power connector Required Tools ● Hand-crimping tool (Tyco Electronics 1490749-1, Upper Die 1490414-2, Lower Die 1-1490413-6). ● Wire-stripper pliers capable of removing insulation from size 4 AWG solid or stranded, insulated copper wire. NOTE: Use alpha wire part number 3080 or equivalent (65/30 stranding).
Figure 41. Assembling and Connecting the Safety Ground Wire 1. grounding post 3. locking washer 2. safety ground wire terminal 4. #5/16 nut Assembling The DC Input Power Wires And DC Power Connector About this task NOTE: For equipment using –(48–60) V DC power supplies, a qualified electrician must perform all connections to DC power and to safety grounds. Do not attempt connecting to DC power or installing grounds yourself.
4. Insert the DC power connector into the power supply. 5. Tighten the screws on the wings of the DC power connector. Figure 42. Assembling the DC Input Power Wires 1. 3. 5. 7. DC power socket captive screws (2) wire –48 V wings (2) 2. rubber cap 4. DC power connector 6. wire RTN Removing A DC Power Supply About this task NOTE: For equipment using –(48–60) V DC power supplies, a qualified electrician must perform all connections to DC power and to safety grounds.
NOTE: The power supply modules have internal fans that provide thermal cooling to these modules. A power supply module must be replaced if an internal fan failure occurs. NOTE: You may have to unlatch and lift the optional cable management arm if it interferes with power supply removal. For information about the cable management arm, see the system’s rack documentation. Steps 1. Disconnect the power wires from the power source and the connector from the power supply you intend to remove. 2.
Steps 1. Verify that both the power supplies are the same type and have the same maximum output power. NOTE: The maximum output power (shown in Watts) is listed on the power supply label. 2. If applicable, remove the power supply blank. 3. Slide the new power supply into the chassis until the power supply is fully seated and the release latch snaps into place. NOTE: If you unlatched the cable management arm, re-latch it. For information about the cable management arm, see the system’s rack documentation. 4.
Figure 44. Removing and Installing A Fan Module a. fan module b. release button Installing A Fan Module Prerequisites CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty.
2. Push the release latch on the handle and rotate the handle away from the module front panel. 3. Slide the CMC module out of the enclosure. 4. Install the I/O connector cover. Figure 45. Removing and Installing a CMC Module or iKVM Module (CMC Module Shown) a. I/O connector cover b. release latch c. release lever Installing A CMC Module Prerequisites CAUTION: Many repairs may only be done by a certified service technician.
Steps 1. Remove the CMC module from the M1000e enclosure. NOTE: Verify the write protection latch is in the "unlock" position. 2. Locate the SD card slot on the bottom of the CMC module and insert the contact-pin end of the card into the slot with the label on the card facing upwards. 3. Reinstall the CMC module and reattach any cables that were disconnected. On a single CMC system, the SD card activates automatically.
Steps 1. Disconnect the cables attached to the iKVM module. 2. Press in the release latch on the handle and rotate the handle away from the module front panel. 3. Slide the module out of the enclosure. 4. Install the I/O connector cover. Figure 47. Removing and Installing a CMC Module or iKVM Module (CMC Module Shown) a. I/O connector cover b. release latch c. release lever Installing An iKVM Module Prerequisites CAUTION: Many repairs may only be done by a certified service technician.
Removing An I/O Module Prerequisites CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that are shipped with your product. Steps 1.
Steps 1. Unpack the I/O module and prepare it for installation. For instructions, see the documentation that accompanied the I/O module. 2. Remove the I/O connector cover from the back of the module. 3. Lift the handle release latch and open the I/O module handle. 4. Slide the module into the enclosure. 5. Close the handle until it snaps securely into place and the module is fully seated. 6. Connect all cables that must be attached to the I/O module.
Figure 49. Removing and Installing the Bezel 1. bezel 3. Torx T20 screws (6) 2. enclosure 4. Torx T8 screws (2) Installing The Enclosure Bezel Prerequisites CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty.
Steps 1. Press the enclosure power switch to turn off the system. CAUTION: To avoid damaging the modules, you must remove all the modules installed in the enclosure before removing the front module cage assembly and midplane. NOTE: If you remove the chassis from the rack, you must remove all modules before moving the chassis. Do not use the LCD display as a handle when moving the chassis. 2. Remove the following: a. b. c. d. e. f.
Figure 51. Removing and Installing the Midplane a. front module cage assembly b. midplane c. Torx T15 screws (4) Installing The Midplane And Front Module Cage Assembly Prerequisites CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team.
Removing The Control Panel Prerequisites CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product. Steps 1. Press the system power switch to turn off the system. 2.
telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product. Steps 1. Connect the LCD panel cable to the new control panel. 2. Connect the control panel cable to the underside of the new control panel. 3. Reinstall the control panel using the two screws. 4. Reinstall the bezel. 5. Install the blades.
Figure 53. Removing and Installing the LCD Module 1. cable cover 3. ribbon cable 5. Torx T8 screws (2) 2. LCD module 4. hinges (2) Installing The LCD Module Prerequisites CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty.
5 Troubleshooting The Enclosure NOTE: For troubleshooting information on the blades in your enclosure, see the blade documentation at support.dell.com/manuals. Safety First—For You and Your System CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team.
● CMC module ● Network switch module Troubleshooting A Wet Enclosure Prerequisites CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that are shipped with your product. Steps 1.
Steps 1. Locate the faulty power supply module and check the indicators. The power supply's AC indicator is green if AC power is available. The power supply's fault indicator is amber if the power supply is faulty. If no indicators are lit, ensure that 208 V AC power is available from the PDU and that the power cable is properly connected to the power supply module. 2. Install a new power supply.
Troubleshooting I/O Modules Prerequisites NOTE: To eliminate the possibility of a hardware problem with the module or its attaching devices, first ensure that the module is properly initialized and configured. Steps 1. Check that you have installed the module in an I/O slot that matches its fabric type. 2. Check that the pass-through module or switch ports are cabled correctly. A given mezzanine card in a full-height blade connects to two I/O ports on the two associated I/O modules. 3.
6 Technical Specifications Table 17. Enclosure Specifications Physical Height 44.0 cm (17.3 inch) Width 44.7 cm (17.6 inch) Depth 75.5 cm (29.7 inch) Weight (maximum) 200.5 kg (442 lb) Weight (empty) 44.6 kg (98.1 lb) Table 18.
Table 18. Power Supply Module (continued) Power Supply Module System voltage requirements 75 A, 48 V DC to 60 V DC Table 19. Optional Avocent iKVM Module Optional Avocent iKVM Module Externally accessible connectors USB Two 4-pin, USB 2.0-compliant connectors for keyboard and mouse support ACI port RJ-45 Video 15-pin VGA Table 20.
Table 22. I/O Module Specifications Dell Force10 MXL 10/40 GbE Switch Module Externally accessible connectors Serial 4-pin, USB 2.0 type A connector. Must use provided USB type A to DB9 adapter to connect to terminal. Optional Modules Two optional bays. Each bay supports an Uplink module with four 40 GbE optical SFP+ connectors, or 10GBASE-T module using RJ-45 connectors. Table 22.
Table 22. I/O Module Specifications Mellanox Infiniband Switch Module Externally accessible connectors Infiniband ports Eight Infiniband uplink ports Table 22. I/O Module Specifications Gb Ethernet Pass-Through Module Externally accessible connectors Ethernet Sixteen RJ-45 ports. Pass-through ports support 10/100/1000 Mbps connections. Table 22.
Table 23. Environmental Specifications (continued) Environmental range, see the technical specifications in the blade's Owner's Manual at dell.com/support/manuals. ● 2700 W power supplies are supported as per the power supply rated capacity. ● 3000 W power supplies are supported with a capacity of 2800 W per power supply. ● Install fans of the following ratings: ○ 12 V, 5.0 A ○ 12 V, 6.
7 Getting help Topics: • • • Contacting Dell EMC Quick Resource Locator Documentation Feedback Contacting Dell EMC Dell EMC provides several online and telephone based support and service options. If you do not have an active internet connection, you can find contact information about your purchase invoice, packing slip, bill, or Dell EMC product catalog. Availability varies by country and product, and some services may not be available in your area.
Figure 54. Quick Resource Locator Documentation Feedback If you have feedback for this document, write to documentation_feedback@dell.com. Alternatively, you can click on the Feedback link in any of the Dell documentation pages, fill up the form, and click Submit to send your feedback.
