Precision 3260 Compact Service Manual Regulatory Model: D16U Regulatory Type: D16U001 March 2022 Rev.
Notes, cautions, and warnings NOTE: A NOTE indicates important information that helps you make better use of your product. CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. WARNING: A WARNING indicates a potential for property damage, personal injury, or death. © 2022 Dell Inc. or its subsidiaries. All rights reserved. Dell, EMC, and other trademarks are trademarks of Dell Inc. or its subsidiaries.
Contents Chapter 1: Working inside your computer...................................................................................... 6 Safety instructions.............................................................................................................................................................. 6 Before working inside your computer....................................................................................................................... 6 Safety precautions....................
Removing the M.2 2280 PCIe solid-state drive (slot-0)................................................................................... 39 Installing the M.2 2280 PCIe solid-state drive (slot-0)..................................................................................... 40 Expansion card....................................................................................................................................................................41 Removing the serial port PCIe card.............
Clearing BIOS (System Setup) and System passwords...........................................................................................87 Chapter 5: Troubleshooting.........................................................................................................88 Dell SupportAssist Pre-boot System Performance Check diagnostics................................................................88 Running the SupportAssist Pre-Boot System Performance Check.............................................
1 Working inside your computer Safety instructions Use the following safety guidelines to protect your computer from potential damage and to ensure your personal safety. Unless otherwise noted, each procedure included in this document assumes that you have read the safety information that shipped with your computer. WARNING: Before working inside your computer, read the safety information that is shipped with your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.
NOTE: If you are using a different operating system, see the documentation of your operating system for shut-down instructions. 3. Disconnect your computer and all attached devices from their electrical outlets. 4. Disconnect all attached network devices and peripherals, such as keyboard, mouse, and monitor from your computer. CAUTION: To disconnect a network cable, first unplug the cable from your computer and then unplug the cable from the network device. 5.
The more difficult type of damage to recognize and troubleshoot is the intermittent (also called latent or "walking wounded") failure. Perform the following steps to prevent ESD damage: ● Use a wired ESD wrist strap that is properly grounded. The use of wireless anti-static straps is no longer allowed; they do not provide adequate protection. Touching the chassis before handling parts does not ensure adequate ESD protection on parts with increased sensitivity to ESD damage.
ESD protection summary It is recommended that all field service technicians use the traditional wired ESD grounding wrist strap and protective anti-static mat at all times when servicing Dell products. In addition, it is critical that technicians keep sensitive parts separate from all insulator parts while performing service and that they use anti-static bags for transporting sensitive components.
2 Removing and installing components NOTE: The images in this document may differ from your computer depending on the configuration you ordered. Recommended tools The procedures in this document may require the following tools: ● Phillips # 1 screwdriver ● Small flat blade screwdriver Screw list NOTE: When removing screws from a component, it is recommended to note the screw type, the quantity of screws, and then place them in a screw storage box.
Table 1. Screw list (continued) Component Screw type Quantity M2x4 3 Speaker holder M3x4 Internal antenna - Location 1 and Location 2 M3x3 2 SATA FFC module M3x5 1 Screw image Major components of Precision 3260 Compact The following image shows the major components of Precision 3260 Compact.
Removing and installing components
1. 3. 5. 7. 9. 11. 13. Side cover Graphics card Speaker Bottom chassis Speaker holder Heat sink Wireless card 2. 4. 6. 8. 10. 12. 14. Riser-card bracket Processor fan System board Coin-cell battery Processor Memory module solid-state drive NOTE: Dell provides a list of components and their part numbers for the original system configuration purchased. These parts are available according to warranty coverages purchased by the customer. Contact your Dell sales representative for purchase options.
Removing and installing components
Steps 1. Loosen the thumbscrew (#6-32) that secures the side cover to the computer. 2. Slide the side cover towards the front of the computer and remove the side cover from the computer. Installing the side cover Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure. About this task The following image indicates the location of the side cover and provides a visual representation of the installation procedure.
Removing and installing components
Steps 1. Align the side cover with the grooves on the computer. 2. Slide the side cover into the chassis towards the front of the computer. 3. Tighten the thumbscrew (#6-32) to secure the side cover to the computer. Next steps 1. Follow the procedure in after working inside your computer. 2.5-inch hard drive Removing the 2.5-inch hard-drive assembly Prerequisites 1. Follow the procedure in before working inside your computer. 2. Remove the side cover.
About this task The following image(s) indicate the location of the 2.5-inch hard-drive assembly and provides a visual representation of the removal procedure. Steps 1. Place the computer on its side with the left side facing up. 2. Press the release tabs on the hard-drive caddy and slide the hard-drive caddy out to disconnect from the connector on the system board. 3. Lift the hard-drive assembly from the computer. NOTE: Note the orientation of the hard drive so that you can replace it correctly.
About this task The following image(s) provides a visual representation of the 2.5-inch hard-drive caddy removal procedure. Steps 1. Pry the hard-drive caddy to release the tabs on the caddy from the slots on the 2.5-inch hard drive. 2. Lift the 2.5-inch hard drive off the hard-drive caddy. Installing the 2.5-inch hard-drive caddy Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure.
Steps 1. Place the 2.5-inch hard drive into the hard-drive caddy and align the tabs on the caddy with the slots on the hard drive. 2. Snap the hard-drive caddy onto the 2.5-inch hard drive. Next steps 1. Install the side cover. 2. Follow the procedure in after working inside your computer. Installing the 2.5-inch hard-drive assembly Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure.
Steps 1. Align and place the hard-drive assembly into the slot on the computer. 2. Slide the hard-drive assembly towards the connector on the system board until it snaps into place. Next steps 1. Install the side cover. 2. Follow the procedure in after working inside your computer. Riser card Removing the riser card Prerequisites 1. Follow the procedure in before working inside your computer. 2. Remove the side cover.
About this task The following image(s) indicate the location of the riser card and provide a visual representation of the removal procedure. Steps 1. Place the computer on its side with the left side facing up. 2. Remove the two (M3x5) screws that secure the riser card to the chassis. 3. Lift the riser card away from the computer.
Installing the riser card Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure. About this task The following image(s) indicate the location of the riser card and provide a visual representation of the installation procedure.
Steps 1. Align the screw holes on the riser card with the screw holes on the chassis. 2. Replace the two (M3x5) screws to secure the riser card to the chassis. Next steps 1. Install the side cover. 2. Follow the procedure in after working inside your computer. Wireless card Removing the wireless card Prerequisites 1. Follow the procedure in before working inside your computer. 2. Remove the side cover. 3. Remove the hard-drive assembly.
Steps 1. Place the computer on its side with the left side facing up. 2. Remove the screw (M2x3) that secure the wireless-card shield to the system board. 3. Lift the wireless-card shield out of the computer. 4. Remove the screw (M2x3) that secure the Wireless-card bracket to the wireless card. 5. Slide and remove the wireless-card bracket off the wireless card. 6. Disconnect the antenna cables from the wireless card. 7. Slide and remove the wireless card from the wireless-card slot.
Installing the wireless card Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure. About this task The following image(s) indicates the location of the wireless card and provides a visual representation of the installation procedure.
Steps 1. Connect the antenna cables to the wireless card. The following table provides the antenna-cable color scheme for the WLAN card of your computer. Table 2. Antenna-cable color scheme Connectors on the wireless card Antenna-cable color Silkscreen marking Main White MAIN △ (white triangle) Auxiliary Black AUX ▲ (black triangle) 2. Place the wireless-card bracket on the wireless card. 3. Align the notch on the wireless card with the tab on the wireless-card slot. 4.
Steps 1. Disconnect the speaker cable from the connector on the system board. 2. Unroute the speaker cable from the routing guide on the fan assembly. 3. Press the release tab and lift the speaker along with the cable from the system board. Installing the speaker Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure.
Steps 1. Align and insert the speaker into the slot and press it until the release tab clicks. 2. Route the speaker cable through the routing guide on the fan assembly. 3. Connect the speaker cable to the connector on the system board. Next steps 1. Install the side cover. 2. Follow the procedure in after working inside your computer. Processor fan Removing the processor fan Prerequisites 1. Follow the procedure in before working inside your computer. 2. Remove the side cover. 3. Remove the speaker.
Steps 1. NOTE: Unroute the speaker cable from the routing guide on the processor fan. Press the blue tabs on both sides of the processor fan, and lift the fan to release it from the computer and turn it over. 2. Disconnect the fan cable from the connector on the system board. 3. Lift the processor fan out of the computer. Installing the processor fan Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure.
Steps 1. Connect the fan cable to the connector on the system board, and turn up-side down. 2. Press the release tab on the processor fan and place it on the computer until it clicks into place. NOTE: Route the speaker cable through the routing guides on the fan assembly. Next steps 1. Install the speaker. 2. Install the side cover. 3. Follow the procedure in after working inside your computer.
Memory module Removing the memory modules Prerequisites 1. Follow the procedure in before working inside your computer. 2. Remove the side cover. 3. Remove the processor fan. About this task The following image(s) indicate the location of the memory modules and provide a visual representation of the removal procedure. Steps 1. Place the computer on its side with the left side facing up. 2. Carefully spread apart the securing-clips on each end of the memory-module slot. 3.
NOTE: If the memory module is difficult to remove, gently ease the memory module back and forth to remove it from the slot. Installing the memory modules Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure. About this task The following image(s) indicate the location of the memory modules and provide a visual representation of the installation procedure. Steps 1.
NOTE: If the memory module is difficult to remove, gently ease the memory module back and forth to remove it from the slot. Next steps 1. Install the processor fan. 2. Install the side cover. 3. Follow the procedure in after working inside your computer. M.2 solid-state drive Removing the M.2 2230 PCIe solid-state drive (slot-1) Prerequisites 1. 2. 3. 4. 5. Follow the procedure in before working inside your computer. Remove the side cover. Remove the processor fan. Remove the riser card—optional.
Steps 1. Place the computer on its side with the left side facing up. 2. Remove the screw (M2x3.5) that secures the 2230 solid-state drive to the system board. 3. Slide and lift the 2230 solid-state drive from the M.2 card slot on the system board. Installing the M.2 2230 PCIe solid-state drive (slot-1) Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure.
3. Install the processor fan. 4. Install the side cover. 5. Follow the procedure in after working inside your computer. Removing the M.2 2280 PCIe solid-state drive (slot-1) Prerequisites 1. 2. 3. 4. 5. Follow the procedure in before working inside your computer. Remove the side cover. Remove the processor fan. Remove the riser card—optional. Remove the hard-drive assembly.
Installing the M.2 2280 PCIe solid-state drive (slot-1) Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure. About this task The following image(s) indicate the location of the solid-state drive and provides a visual representation of the installation procedure. Steps 1. Align the notch on the 2280 solid-state drive with the tab on the M.2 card slot on the system board. 2. Slide the 2280 solid-state drive into the M.
Removing the M.2 2230 PCIe solid-state drive (slot-0) Prerequisites 1. 2. 3. 4. 5. Follow the procedure in before working inside your computer. Remove the side cover. Remove the processor fan. Remove the riser card—optional. Remove the hard-drive assembly. About this task The following image(s) indicate the location of the solid-state drive and provide a visual representation of the removal procedure. Steps 1. Place the computer on its side with the left side facing up. 2. Remove the screw (M2x3.
About this task The following image(s) indicate the location of the solid-state drive and provides a visual representation of the installation procedure. Steps 1. Align the notch on the 2230 solid-state drive with the tab on the M.2 card slot on the system board. 2. Slide the 2230 solid-state drive into the M.2 card slot on the system board. 3. Replace the screw (M2x3.5) that secures the 2230 solid-state drive to the system board. 4. Place the computer in an upright position. Next steps 1. 2. 3. 4. 5.
5. Remove the hard-drive assembly. About this task The following image(s) indicate the location of the solid-state drive and provide a visual representation of the removal procedure. Steps 1. Place the computer on its side with the left side facing up. 2. Remove the screw (M2x3.5) that secures the 2280 solid-state drive to the system board. 3. Slide and lift the 2280 solid-state drive from the M.2 card slot on the system board. Installing the M.
Steps 1. Align the notch on the 2280 solid-state drive with the tab on the M.2 card slot on the system board. 2. Slide the 2280 solid-state drive into the M.2 card slot on the system board. 3. Replace the screw (M2x3.5) that secures the 2280 solid-state drive to the system board. 4. Place the computer in an upright position. Next steps 1. 2. 3. 4. 5. Install the hard-drive assembly. Install the riser card—optional. Install the processor fan. Install the side cover.
About this task The following image(s) indicate the location of the serial port PCIe card and provide a visual representation of the removal procedure. Steps 1. Place the computer on its side with the left side facing up. 2. Open the PCI retainer latch. 3. Slide and remove the serial port PCIe card out of the computer. 4. Insert the PCIe bracket and close the PCI retainer latch.
Steps 1. Open the PCI retainer latch and slide the PCIe bracket out of the computer. 2. Align the serial port PCIe card and slide it into the slot on the computer. 3. Ensure to check the serial port PCIe card assembly is placed within the structure limit. 4. Close the PCI retainer latch. Next steps 1. Install the side cover. 2. Follow the procedure in after working inside your computer. Removing the graphics card Prerequisites 1. Follow the procedure in before working inside your computer. 2.
About this task The following image(s) indicate the location of the graphics card and provide a visual representation of the removal procedure. Steps 1. Pull and open the PCI retainer latch. 2. Slide the graphics card along the edges of the riser card to release it from the riser card. 3. Remove the two (M3x5) screws that secure the riser card to the chassis. 4. Lift the riser card away from the computer.
Steps 1. Align the screw holes on the riser card with the screw holes on the chassis. 2. Replace the two (M3x5) screws to secure the riser card to the chassis. 3. Slide the graphics card into the slot on the riser card until it clicks into place. 4. Close the PCI retainer latch and press until it clicks into place. Next steps 1. Install the side cover. 2. Follow the procedure in after working inside your computer.
Optional I/O module Removing the optional I/O module Prerequisites 1. 2. 3. 4. Follow the procedure in before working inside your computer. Remove the side cover. Remove the hard-drive assembly. Remove the riser card. About this task The following image(s) indicate the location of the optional I/O module and provide a visual representation of the removal procedure. Steps 1. Place the computer on its side with the left side facing up.
2. Remove the two screws (M3x3) that secure the optional I/O module to the chassis. NOTE: The screw type differs with the kind of I/O module used. 3. Slide and remove the optional I/O module from its slot in the chassis. 4. Disconnect the cable that connects the optional I/O module to the system board. 5. Remove the I/O module from the computer. Installing the optional I/O module Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure.
Steps 1. Insert a flat-head screwdriver in the dummy optional-I/O module bracket. 2. Push the bracket to release the bracket from the chassis. 3. Connect the I/O-module cable to the connector on the system board. 4. Insert the I/O module into the slot from the inside your computer. 5. Replace the two screws (M3x3) to secure the optional I/O module to the chassis. NOTE: The screw type differs with the kind of I/O module used. 6. Place the computer in an upright position. Next steps 1. 2. 3. 4.
3. Remove the riser card. 4. Remove the optional I/O module . NOTE: Removing the coin-cell battery resets the BIOS setup program settings to default. It is recommended that you note the BIOS setup program settings before removing the coin-cell battery. About this task The following image(s) indicate the location of the coin-cell battery and provide a visual representation of the removal procedure. Steps 1. Place the computer on its side with the left side facing up. 2.
Steps 1. Insert the coin-cell battery into the socket with the positive side (+) label facing up and snap the battery in the socket. 2. Place the computer in an upright position. Next steps 1. 2. 3. 4. Install the optional I/O module. Install the riser card. Install the side cover. Follow the procedure in after working inside your computer. Heat sink Removing the heat sink Prerequisites 1. Follow the procedure in before working inside your computer. 2. Remove the side cover. 3. Remove the processor fan.
NOTE: For maximum cooling of the processor, do not touch the heat transfer areas on the heat sink. The oils in your skin can reduce the heat transfer capability of the thermal grease. The following image(s) indicate the location of the heat sink and provide a visual representation of the removal procedure. Steps 1. Place the computer on its side with the left side facing up. 2. Loosen the three captive screws in the sequential order (1->3->2) that secure the heat sink to the computer. 3.
Installing the heat sink Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure. About this task NOTE: If either the processor or the fan and heat-sink assembly is replaced, use the thermal grease provided in the kit to ensure that thermal conductivity is achieved. The following image indicates the location of the heat sink and provides a visual representation of the installation procedure.
Steps 1. Align the screw holes on the heat sink with the screw holes on the system board. 2. Tighten the three captive screws in a sequential order (1->2->3) to secure the heat sink to the system board. 3. Place the computer in an upright position. Next steps 1. Install the processor fan. 2. Install the side cover.
3. Follow the procedure in after working inside your computer. SATA FFC module Removing the SATA FFC module Prerequisites 1. 2. 3. 4. Follow the procedure in before working inside your computer. Remove the side cover. Remove the processor fan. Remove the hard drive. About this task The following image(s) indicate the location of the SATA FFC module and provide a visual representation of the removal procedure. Steps 1.
Steps 1. Align the screw hole on the SATA FFC module with the screw hole on the system board. 2. Replace the single screw (M3x5) that secures the SATA FFC module to the system board. 3. Connect the SATA FFC to the connector on the system board and close the latch. Next steps 1. 2. 3. 4. Install the hard drive. Install the processor fan. Install the side cover. Follow the procedure in after working inside your computer. Processor Removing the processor Prerequisites 1. 2. 3. 4.
Steps 1. Press the release lever down and then push it away from the processor to release it from the securing tab. 2. Extend the release lever completely and open the processor cover. CAUTION: When removing the processor, do not touch any of the pins inside the socket or allow any objects to fall on the pins in the socket. 3. Gently lift the processor from the processor socket.
Installing the processor Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure. About this task The following image(s) indicate the location of the processor and provides a visual representation of the installation procedure.
Steps 1. Ensure that the release lever on the processor socket is fully extended in the open position. NOTE: The pin-1 corner of the processor has a triangle that aligns with the triangle on the pin-1 corner on the processor socket. When the processor is properly seated, all four corners are aligned at the same height. If one or more corners of the processor are higher than the others, the processor is not seated properly. 2.
1. M.2 2230/2280 solid-state drive PCIe connector (SSD-1 slot) 3. Optional video port connector 5. SATA FFC connector 7. PCIe x8 Gen4 slot 9. Processor fan connector 11. Memory modules 2. Coin-cell battery 4. 6. 8. 10. 12. USB Type-C connector Keyboard and mouse serial port connector Processor Internal speaker connector M.2 2230/2280 solid-state drive PCIe connector (SSD-0 slot) 13. M.
Removing and installing components
Steps 1. Remove the single screw (M3x4) that secures the speaker holder to the system board. 2. Lift and remove the speaker holder away from the system board. 3. Remove the four screws (M3x4) that secure the system board to the chassis. 4. Remove the three screws (M2x4) that secure the system board to the chassis. 5. Slide and lift the system board away from the chassis.
1. M.2 2230/2280 solid-state drive PCIe connector (SSD-1 slot) 3. Optional video port connector 5. SATA FFC connector 7. PCIe x8 Gen4 slot 9. Processor fan connector 11. Memory modules 2. Coin-cell battery 4. 6. 8. 10. 12. USB Type-C connector Keyboard and mouse serial port connector Processor Internal speaker connector M.2 2230/2280 solid-state drive PCIe connector (SSD-0 slot) 13. M.
Removing and installing components 63
Steps 1. Align the screw holes on the system board with screw holes on the chassis. 2. Replace the three screws (M2x4) to secure the system board to the chassis. 3. Replace the three screws (M3x4) to secure the system board to the chassis. 4. Align the screw hole on the speaker holder with the screw hole on the system board. 5. Replace the single screw (M3x4) to secure the speaker holder to the system board. Next steps 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14.
Internal antennae Removing the internal antenna—location 1 Prerequisites 1. 2. 3. 4. 5. Follow the procedure in before working inside your computer. Remove the side cover. Remove the hard-drive assembly—optional. Remove the riser card—optional. Remove the wireless card. About this task The following image(s) indicate the location of the internal antenna and provide a visual representation of the removal procedure. Steps 1.
2. Remove the antenna cable from the securing clip on the computer. 3. Remove the single (M3x3) screw that secures the internal antenna to the chassis. 4. Remove the antenna holder ribs from the holes on the chassis. 5. Lift the internal antenna module away from the chassis. Installing the internal antenna—location 1 Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure.
4. Replace the single (M3x3) secure to secure the internal antennae to the chassis. 5. Replace the antenna cable into securing clip on the computer. 6. Route the antenna cable through the metallic routing guides under the EMI shielding along with the chassis using a plastic scribe. Next steps 1. 2. 3. 4. 5. Install the wireless card. Install the riser card—optional. Install the hard-drive assembly—optional. Install the side cover. Follow the procedure in after working inside your computer.
Steps 1. Pry the metallic routing guide and unroute the antenna cables from the chassis. 2. Remove the single screw (M3x3) that secures the internal antennae to the chassis. 3. Lift and remove the internal antennae away from the computer. Installing the internal antenna—location 2 Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure.
Steps 1. Remove adhesive tape and place the Aux antenna stand off into the hole on the chassis. 2. Align the antenna module screw hole with the screw hole on the chassis. 3. Replace the single screw (M3x3) to secure the internal antennae to the chassis. 4. Route the antenna cable through the metallic routing guide on the computer. Next steps 1. 2. 3. 4. 5. Install the wireless card. Install the riser card—optional. Install the hard-drive assembly—optional. Install the side cover.
3. Remove the hard-drive assembly—optional. 4. Remove the riser card—optional. About this task The following images indicate the location of the SMA antenna and provide a visual representation of the removal procedure. Steps 1. Remove the cable-protective cover from the SMA antenna. 2. Loosen the nut using the 8 mm wrench or with automatic screw driver. 3. Remove the SMA antenna module out of the chassis. 4. Remove the single (M2x3.5) screw that secures the wireless-card shield to the system board. 5.
Installing the SMA antenna—Location 3 Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure. About this task The following image indicates the location of the SMA antenna and provides a visual representation of the installation procedure. Steps 1. Route the location1 and location 2 internal antenna cables through the securing clip on the chassis. 2. Connect the antenna cables to the wireless card. 3.
8. Route the antenna cables through the routing guides on the sides of the system board. 9. Remove the cable-protective cover from the SMA antenna. 10. Use a screwdriver remove the upper filler in the SMA antenna holes on the chassis. 11. Insert the SMA antenna module through the bottom cover inside the chassis. 12. Tighten the nut using the 8 mm wrench or with automatic screw driver. 13. Replace the cable-protective cover to the SMA antenna. Next steps 1. 2. 3. 4. 72 Install the riser card—optional.
3 Drivers and downloads When troubleshooting, downloading or installing drivers it is recommended that you read the Dell Knowledge Based article, Drivers and Downloads FAQ 000123347.
4 BIOS setup CAUTION: Unless you are an expert computer user, do not change the settings in the BIOS Setup program. Certain changes can make your computer work incorrectly. NOTE: Depending on the computer and its installed devices, the items listed in this section may or may not be displayed. NOTE: Before you change BIOS Setup program, it is recommended that you write down the BIOS Setup program screen information for future reference.
The one-time boot menu displays the devices that you can boot from including the diagnostic option. The boot menu options are: ● Removable Drive (if available) ● STXXXX Drive (if available) NOTE: XXX denotes the SATA drive number. ● Optical Drive (if available) ● SATA Hard Drive (if available) ● Diagnostics The boot sequence screen also displays the option to access the System Setup screen.
Table 4. System setup options—System information menu (continued) Overview Memory Information Memory Installed Displays the total system memory installed. Memory Available Displays the total system memory available. Memory Speed Displays the memory speed. Memory Channel Mode Displays single or dual channel mode. Memory Technology Displays the technology that is used for the memory. Devices Information Panel Type Displays the Panel Type of the system.
Table 6. System setup options—Integrated Devices menu (continued) Integrated Devices Enable Audio Enable or disable the integrated audio controller. By default, all the options are enabled. USB Configuration ● Enable or disable booting from USB mass storage devices that are connected to external USB ports. By default, the Enable External USB Ports option is enabled. ● Enable or disable booting from USB mass storage devices such as external hard drive, optical drive, and USB drive.
Table 8. System setup options—Display menu (continued) Display EcoPower Enable or disable EcoPower Feature in your panel. EcoPower can increase the battery life of your system by reducing the display brightness when appropriate. By default, Enable EcoPower option is enabled. Full Screen Logo Enable or disable full screen logo. By default, the option is not enabled. Table 9. System setup options—Connection menu Connection Wireless Device Enable WLAN Enable or disable the internal WLAN device.
Table 10. System setup options—Power menu (continued) Power NOTE: This feature is only functional when the AC power adapter is connected. If the AC power adapter is removed before Standby, the BIOS will remove power from all of the USB ports to conserve battery power. By default, the Enable USB Wake Support option is disabled. Wake on Dell USB-C Dock When enabled, connecting a Dell USB-C Dock will wake the system from Standby, Hibernate, and Power Off.
Table 11. System setup options—Security menu (continued) Security By default, the Start Data Wipe option is disabled. Absolute Enable or disable or permanently disable the BIOS module interface of the optional Absolute Persistence Module service from Absolute software. By default, the option is enabled. WARNING: The 'Permanently Disabled' option can only be selected once. When 'Permanently Disabled' is selected, Absolute Persistence cannot be re-enabled.
Table 12. System setup options—Passwords menu (continued) Passwords Enable Master Password Lockout When enabled, this disables the master password support. By default, the option is disabled. Allow Non-Admin PSID Revert Enable Allow Non-Admin PSID Revert Controls access to the Physical Security ID (PSID) revert of NVMe hard-drives from the Dell Security Manager prompt. By default, the option is disabled. Table 13.
Table 14. System setup options—System Management menu (continued) System Management By default, the option is disabled. Table 15. System setup options—Keyboard menu Keyboard Numlock Enable Allows you to enable or disable the Numlock function when the system boots. By default, the option Fn Lock Options is enabled. Fn Lock Options By default, the Fn lock option is enabled. Lock Mode By default, the Lock Mode Secondary option is enabled.
Table 17. System setup options—Virtualization menu (continued) Virtualization ● Intel VT for Direct I/O By default, the option is disabled. Table 18. System setup options—Performance menu Performance Multi Core Support Active Cores Enables to change the number of CPU cores available to the operating system. By default, the All Cores option is enabled.
Updating the BIOS Updating the BIOS in Windows About this task CAUTION: If BitLocker is not suspended before updating the BIOS, the next time you reboot the system it will not recognize the BitLocker key. You will then be prompted to enter the recovery key to progress and the system will ask for this on each reboot. If the recovery key is not known this can result in data loss or an unnecessary operating system re-install. For more information on this subject, see Knowledge Article: https:// www.dell.
Updating the BIOS from the F12 One-Time boot menu Update your computer BIOS using the BIOS update.exe file that is copied to a FAT32 USB drive and booting from the F12 One-Time boot menu. About this task CAUTION: If BitLocker is not suspended before updating the BIOS, the next time you reboot the system it will not recognize the BitLocker key. You will then be prompted to enter the recovery key to progress and the system will ask for this on each reboot.
CAUTION: The password features provide a basic level of security for the data on your computer. CAUTION: Anyone can access the data that is stored on your computer if it is not locked and left unattended. NOTE: System and setup password feature is disabled. Assigning a system setup password Prerequisites You can assign a new System or Admin Password only when the status is in Not Set. About this task To enter the system setup, press F12 immediately after a power-on or reboot. Steps 1.
Clearing CMOS settings About this task CAUTION: Clearing CMOS settings will reset the BIOS settings on your computer. Steps 1. Remove the side cover. 2. Remove the riser card. 3. Remove the coin-cell battery. 4. Wait for one minute. 5. Replace the coin-cell battery. 6. Replace the riser card. 7. Replace the side cover. Clearing BIOS (System Setup) and System passwords About this task To clear the system or BIOS passwords, contact Dell technical support as described at www.dell.com/contactdell.
5 Troubleshooting Dell SupportAssist Pre-boot System Performance Check diagnostics About this task SupportAssist diagnostics (also known as system diagnostics) performs a complete check of your hardware. The Dell SupportAssist Pre-boot System Performance Check diagnostics is embedded with the BIOS and is launched by the BIOS internally.
Table 21. System-diagnostic lights (continued) Blinking pattern Amber White Problem description 2 1 CPU failure Suggested resolution ● ● 2 2 2 3 System board failure (included ● BIOS corruption or ROM ● error) No memory/RAM detected ● ● 2 4 Memory/RAM failure ● ● 2 5 Invalid memory installed ● ● 2 6 System board/Chipset Error 3 1 CMOS battery failure Run the Dell Support Assist/Dell Diagnostics tool. If problem persists, replace the system board.
Table 21. System-diagnostic lights (continued) Blinking pattern Amber White Problem description Suggested resolution ● ● 3 7 Timeout waiting on ME to reply to HECI message. ● ● 4 2 seconds to ensure all power are drained. Run "BIOS recovery from USB", and the instructions are in the website Dell support. If problem persists, replace the system board. Timeout waiting on ME to reply to HECI message If problem persists, replace the system board.
The below items may or may not reset based on your custom BIOS setting selections: ● ● ● ● Boot List Enable Legacy Option ROMs Secure Boot Enable Allow BIOS Downgrade Backup media and recovery options It is recommended to create a recovery drive to troubleshoot and fix problems that may occur with Windows. Dell proposes multiple options for recovering Windows operating system on your Dell PC. For more information. see Dell Windows Backup Media and Recovery Options.
Table 22. Computer behavior with hard drives and add-in cards which do not support modern standby (continued) System behavior Screen dGfx fan Hard drive LED PWR LED Processor fan MODS "Should be" Off Off Off Off Off MODS normal after Off second entry on SATA hard drive Off Off Off Off Intel System Agent Enhanced Speed Step (SAGV) always disabled For Precision 3260 Compact, the SAGV option is disabled by default.
6 Getting help and contacting Dell Self-help resources You can get information and help on Dell products and services using these self-help resources: Table 23. Self-help resources Self-help resources Resource location Information about Dell products and services www.dell.com My Dell app Tips Contact Support In Windows search, type Contact Support, and press Enter. Online help for operating system www.dell.com/support/windows www.dell.
