Item #317526607/317526608 Model #IS01a012NK-50W1/IS01a012NK-50B1 USE AND CARE GUIDE MOTION SECURITY LIGHT Questions, problems, missing parts? 8 a.m.-7 p.m., EST, Monday-Friday, 9 a.m. - 6 p.m., EST, Saturday 1-866-308-3976 HOMEDEPOT.COM THANK YOU We strive to continually create quality products designed to enhance your home.
Table of Contents Tools Required .......................................3 Hardware Included.................................4 Package Contents ..................................4 Installation ................................................5 Operation...................................................8 Care and Cleaning ..................................10 Troubleshooting ......................................10 Table of Contents ......................................2 Safety Information ..................
Pre-Installation PLANNING INSTALLATION Hardware Included and Package Contents sections. If any part is missing or damaged, do not attempt to assemble, install, or operate this SPECIFICATIONS Range Up to 40 ft. (12.2 m) (Varies with surrounding temperature) Sensing angle Up to 240° Wattage 12 Watts Lumens 1200lm Input voltage 120 VAC, 60 Hz Operating modes Test, Motion on, DTD(motion off) Time delay Adjustable – 1, 5, 10 minutes TOOLS REQUIRED Phillips screwdriver 1/8 in.
Pre-Installation (continued) HARDWARE INCLUDED NOTE: Hardware shown to actual size.
Installation the mounting 1 Determining location NOTE: mounted higher than recommended, aiming the sensor down will reduce the coverage area. □ □ Wall Mount Determine the mounting location – wall or eave mount. Position the lamp heads (A) in the general direction of the desired light coverage. A Eave Mount the electrical 2 Installing the mounting bracket 3 Making connections WARNING: Turn the power off at the circuit breaker or fuse.
Installation (continued) 4 Mounting the light fixture □ □ FF Align the fixture (B) with the mounting plate (FF). And then tighten the mounting bolt (EE) securely through the center of the mounting plate (FF). Do not over tighten. EE Push the rubber plug (AA) firmly into the mounting bolt hole on the light fixture (B). B NOTICE: When attaching this light to an external, surface mount junction box, caulk around the inside of the light fixture (B) before attaching to the light fixture (B).
Operation 1 Adjusting the lamp heads WARNING: □ □ Turn the power on at the circuit breaker or fuse and turn on the wall switch. If needed, gently grasp the lamp heads (A) and tilt them up or down or side to side to adjust the light coverage area. 2 Setting the sensor for testing NOTE: The motion sensor will need to completely warm up (30 seconds) before beginning the setup process. NOTE: When the “Test / Timer” control is set to the “Test” night.
Operation (continued) the SENSITIVITY 4 Adjusting control □ □ To increase the sensitivity, turn the “SENSITIVITY” control counterclockwise. To decrease the sensitivity, turn the “SENSITIVITY” control clockwise. NOTE: The motion sensor (C) is more sensitive to motion moving across the front of the sensor. The motion sensor (C) is less sensitive to motion moving directly toward the front of the sensor. NOTE: The higher the “SENSITIVITY” setting, the greater the possibility of false triggering.
Care and Cleaning □ □ □ Troubleshooting Problem Possible Cause Solution The light will not come on. □ The light switch is turned off. □ Turn the light switch on. □ The fuse is blown or the circuit breaker is turned off. □ Replace the fuse or turn the circuit breaker on. □ Daylight turn-off (photocell) is in effect. □ Recheck after dark. □ The circuit wiring is incorrect (if this is a new installation). □ Verify the wiring is correct. □ The motion sensor is aimed in the wrong direction.
Troubleshooting (continued) Problem Possible Cause Solution The lights stay on continuously. □ □ Decrease the “SENSITIVITY” setting or reposition the motion sensor. □ Do not use a dimmer or timer to control the light The motion sensor may be picking up a heat source, such as an air vent, dryer surface. □ dimmer or timer. or timer with a standard on/ off wall switch. □ □ a circuit without motors, bulb. bulbs. □ □ □ Heat or light from the bulbs may be turning the motion sensor on and off.
Questions, problems, missing parts? 8 a.m.-7 p.m., EST, Monday-Friday, 9 a.m. - 6 p.m., EST, Saturday 1-866-308-3976 HOMEDEPOT.COM Retain this manual for future use.
