Item #703390 703499 Model #DF-5416-BK-B DF-5416-WH-B USE AND CARE GUIDE MOTION SECURITY LIGHT Questions, problems, missing parts? 8 a.m.-7 p.m., EST, Monday-Friday, 9 a.m. - 6 p.m., EST, Saturday 1-866-308-3976 HOMEDEPOT.COM THANK YOU We strive to continually create quality products designed to enhance your home.
Table of Contents Tools Required........................................3 Hardware Included..................................4 Package Contents...................................5 Mounting Locations................................5 Installation.................................................6 Operation...................................................7 Care and Cleaning...................................10 Troubleshooting.......................................10 Table of Contents.........................
Range Up to 70 ft. (21.3 m) - Varies with surrounding temperature Sensing angle Up to 180° Electrical load - incandescent Up to 240 watt maximum (Up to 120 watt maximum per bulb holder) Power requirements 120 VAC, 60 Hz Operating modes Test, Auto, Manual Bulb modes Security, BulbSaver, AlertFlash Time delay 1, 5, 20 minutes DualBrite timer Off, 3 hours, 6 hours, dusk-to-dawn Pre-Installation PLANNING INSTALLATION Hardware Included on page 4).
Pre-Installation (continued) HARDWARE INCLUDED NOTE: Hardware shown to actual size.
Pre-Installation (continued) PACKAGE CONTENTS B A A D D C Part Description Quantity A Bulb holder 2 B Canopy 1 C Motion sensor 1 D Shell 2 MOUNTING LOCATIONS □□ Determine the mounting location – a wall or under an eave. □□ Position bulb holders (A) in the general direction of the desired light coverage and tighten the lock nuts (1) and the thumb screws (2). Wall Mount □□ If needed, lift the motion sensor (C) up and rotate it so the controls face the ground after installation.
Installation the Mounting 1 Installing Bracket the Light Fixture 2 Hanging Temporarily □□ Insert the small end of the plastic hanger (II) through the center hole of the canopy (B) and the gasket (GG). □□ Insert the small end of the plastic hanger (II) into one of the two small, slotted holes on the mounting bracket (HH). □□ Route the light fixture wires through the large holes in the gasket (GG). WARNING: Turn the power off at the circuit breaker or fuse.
Installation (continued) Around the Light 5 Caulking Fixture 6 Installing the Shells and Bulbs □□ Align the three slots on the shell (D) with the three nibs on the bulb holder (A). □□ Insert the shell (D) into the bulb holder (A) and twist clockwise to lock. □□ Repeat for the other shell (D). □□ Install bulbs (not included) into both bulb holders (A). □□ Caulk around the canopy (B) and mounting surface with silicone sealant (not included).
Operation (continued) the Motion Sensor 3 Setting the Sensor for Testing 4 Adjusting Detection Zone When the “ON-TIME” switch is set to the “TEST” position, the light fixture will operate during the day or night. The light will stay on for 5 seconds after all motion is stopped. □□ Turn on the circuit breaker or fuse and the light switch. □□ Perform a “walk test”. Walk in an arc across the front of the motion sensor (C). □□ Watch the light.
Operation (continued) the DUALBRITE 7 Adjusting Switch the LAMP MODE 8 Adjusting Switch The “DUALBRITE” switch determines the amount of time the lights stay on at a reduced light level after sundown. Switching this setting to “OFF” will not effect the “ON-TIME” setting. The “LAMP MODE” switch determines the way the lights will turn on when motion is detected. □□ Security (“NORMAL”) - Light comes on instantly. □□ BulbSaver (“SOFT”) - Light comes on dim and gradually increases to full brightness.
Care and Cleaning □□ To prolong the original appearance, clean with clear water and a soft, damp cloth only. □□ Do not use paints, solvents, or other chemicals on this light fixture. They could cause a premature deterioration of the finish. This is not a defect in the finish and will not be covered by the warranty. □□ Do not spray with a hose or power washer. Troubleshooting Problem The light will not come on. The light comes on during the day. The light comes on for no apparent reason.
Troubleshooting (continued) Problem The lights stay on continuously. Possible Cause Solution □ A bulb is positioned too close to the motion sensor or pointed at nearby objects that cause heat to trigger the light sensor. □ Reposition the bulb away from the motion sensor or nearby objects. □ The motion sensor may be picking up a heat source like an air vent, dryer □ Decrease the “RANGE” setting or reposition the motion sensor. □ Switch the motion sensor to auto. See Using Manual Mode on page 9.
Questions, problems, missing parts? 8 a.m.-7 p.m., EST, Monday-Friday, 9 a.m. - 6 p.m., EST, Saturday 1-866-308-3976 HOMEDEPOT.COM Retain this manual for future use.
Articulo #703390 703499 Modelo #DF-5416-BK-B DF-5416-WH-B GUÍA PARA EL USO Y CUIDADO LUZ DE SEGURIDAD POR MOVIMIENTO ¿Tiene preguntas, problemas o piezas faltantes? de 08 a.m.-7 p.m., EST, Lunes - Viernes, 09 a.m.-6 p.m., EST, sábado. 1-866-308-3976 HOMEDEPOT.COM GRACIAS movimiento. Procuramos crear continuamente productos de calidad diseñados para mejorar su hogar. Visítenos en internet para ver nuestra línea completa de productos disponibles que necesita para el mejoramiento de su hogar.
Contenido Contenido.................................................14 Información de seguridad.......................14 Precauciones........................................14 Garantía...................................................14 2 Años de Garantía................................14 Especificaciones......................................15 Antes de la instalación............................15 Planificación de la Instalación..............15 Herramientas Requeridas.....................
Alcance Hasta 70 pies (21,3 m) – Varía con la temperatura circundante Ángulo de detección Hasta 180° Carga eléctrica-Incandescente Hasta 240 vatios máximo (Hasta 120 vatios máximo por cada porta-bombillas) Requisitos de la energía eléctrica 120 VCA, 60 Hz Fases de operación Prueba, automática, manual Fases de la bombilla Seguridad, ahorrador de bombilla, destello de alerta Retardo de tiempo 1, 5, 20 minutos Temporizador DualBrite Apagado, 3 horas, 6 horas, del crepúsculo al amanecer Antes de
Antes de la instalación (continuación) FERRETERÍA INCLUIDA NOTA: La ferretería se muestra en su tamaño real AA BB CC DD GG Pieza EE HH FRONT Descripción Cantidad AA Capuchón para cable 3 BB Tapón de caucho 1 CC Tornillo de montaje 1 DD Tornillo del soporte de montaje 2 EE Tornillo del soporte de montaje 2 FF Tornillo del soporte de montaje 2 GG Empaque (no está a escala) 1 HH Soporte de montaje (no está a escala) 1 Colgador plástico (no está a escala) 1 II FF 16 II
Antes de la instalación (continuación) CONTENIDO DEL PAQUETE A B A D D C Pieza Descripción Cantidad A Porta bombilla 2 B Escudete 1 C Detector de movimiento 1 D Casco 2 SITIOS PARA EL MONTAJE □□ Determine el sitio para el montaje - una pared o debajo de un alero.
Instalación del soporte de 1 Instalación montaje temporalmente el 2 Cuelgue aparato de luz □□ Inserte el extremo corto del colgador plástico (II) pasándolo por el agujero central del escudete (B) y del empaque (GG). □□ Inserte el extremo corto del colgador plástico (II) en uno de los dos agujeros pequeños y ranurados del soporte de montaje (HH). □□ Pase los conductores del aparato de luz por los agujeros grandes del empaque (GG).
Instalación (continuación) alrededor del aparato de los cascos y las 5 Calafatee 6 Instalación de luz bombillas □□ Calafatee alrededor del escudete (B) y en la superficie de montaje con un sellador de silicona (no incluido) □□ Alinee las tres ranuras del casco (D) con los tres puntas del porta bombillas (A). □□ Inserte el casco (D) en el porta-bombillas (A) y gírelo en sentido horario para bloquearlo. □□ Repita igual con el otro casco (D).
Operación (continuación) del detector para de la zona de 3 Calibración 4 Regulación prueba detección del detector de movimiento Cuando el interruptor de “DURACIÓN” (“ON-TIME”) se fija en la posición “PRUEBA” (“TEST”) el aparato de luz operará durante el día o la noche. La luz permanecerá encendida 5 segundos después que todo movimiento se ha detenido. □□ Conecte el disyuntor o el fusible y el interruptor de la lámpara. □□ Haga una “prueba caminando”.
Operación (continuación) del interruptor 7 Regulación DUALBRITE El interruptor DUALBRITE determina el lapso de tiempo que la luz permanece encendida con un nivel de luz reducido luego de la puesta del sol. Cambiando esta calibración a “OFF” (“DESCONECTADO”) no quedará afectada la calibración de la DURACIÓN. El interruptor FASE LÁMPARA determina la manera en que las luces se encenderán cuando se detecta movimiento. □□ Seguridad (“NORMAL”)- La luz se enciende instantáneamente.
Cuidado y limpieza □□ Para mantener la apariencia original, limpie solamente con agua limpia y un paño húmedo y suave. □□ No use pinturas, solventes ni otros químicos en este aparato de luz. Podrían ser la causa de una prematura deterioración del acabado. Esto no es un defecto del acabado y no será cubierto por la garantía. □□ No rocíe con manguera ni con una lavadora eléctrica. Análisis de averías Problema La lámpara no se enciende. La luz se enciende durante el día.
Análisis de averías (continuación) Problema Causa Probable Solución Las luces se apagan demasiado tarde en la calibración crepúsculo-al-amanecer. El aparato de luz puede estar instalado en un sitio relativamente oscuro. Las luces permanecen encendidas constantemente. □ Una bombilla está demasiado cerca del □ detector de movimiento o enfocando a objetos cercanos que producen calor y activan el detector de luz.
¿Tiene preguntas, problemas o piezas faltantes? de 08 a.m.-7 p.m., EST, Lunes - Viernes, 09 a.m.-6 p.m., EST, sábado. 1-866-308-3976 HOMEDEPOT.COM Guarde este manual para uso futuro.