Item #703390 703499 Model #DF-5416-BK-A DF-5416-WH-A USE AND CARE GUIDE MOTION SECURITY LIGHT Questions, problems, missing parts? Before returning to the store, call Defiant Customer Service 8 a.m. - 6 p.m., EST, Monday - Friday 1-866-308-3976 HOMEDEPOT.COM THANK YOU We appreciate the trust and confidence you have placed in Defiant through the purchase of this motion security light. We strive to continually create quality products designed to enhance your home.
Table of Contents Tools Required .......................................3 Hardware Included.................................4 Package Contents ..................................5 Mounting Locations ...............................5 Installation ................................................6 Operation...................................................7 Care and Cleaning ..................................10 Troubleshooting ......................................10 Table of Contents .........................
Specifications Range Up to 70 ft. (21.
Pre-Installation (continued) HARDWARE INCLUDED NOTE: Hardware shown to actual size.
Pre-Installation (continued) PACKAGE CONTENTS B A A D D C Part Description Quantity A Bulb holder 2 B Canopy 1 C Motion sensor 1 D Shell 2 MOUNTING LOCATIONS Ƒ Determine the mounting location – a wall or under an eave. Ƒ Position bulb holders (A) in the general direction of the desired light coverage and tighten the lock nuts (1) and the thumb screws (2). Ƒ If needed, lift the motion sensor (C) up and rotate it so the controls face the ground after installation.
Installation the Mounting 1 Installing Bracket the Light Fixture 2 Hanging Temporarily Ƒ WARNING: Turn the power off at the circuit breaker or fuse. Place tape over the circuit breaker switch and verify power is off at the light fixture. Ƒ Ƒ Insert the small end of the plastic hanger (II) through the center hole of the canopy (B) and the gasket (GG). Insert the small end of the plastic hanger (II) into one of the two small, slotted holes on the mounting bracket (HH).
Installation (continued) Around the Light 5 Caulking Fixture Ƒ 6 Installing the Shells and Bulbs Ƒ Caulk around the canopy (B) and mounting surface with silicone sealant (not included). Ƒ Ƒ Ƒ Align the three slots on the shell (D) with the three nibs on the bulb holder (A). Insert the shell (D) into the bulb holder (A) and twist clockwise to lock. Repeat for the other shell (D). Install bulbs (not included) into both bulb holders (A).
Operation (continued) the Motion Sensor 3 Setting the Sensor for Testing 4 Adjusting Detection Zone Ƒ When the “ON-TIME” switch is set to the “TEST” position, the light fixture will operate during the day or night. The light will stay on for 5 seconds after all motion is stopped. Ƒ Ƒ Ƒ Ƒ Ƒ Ƒ Set the “ON-TIME” switch to the “TEST” position. Set the “DUALBRITE” switch to the “OFF” position. Turn the “RANGE” dial to the “MIN” position.
Operation (continued) the DUALBRITE 7 Adjusting Switch the LAMP MODE 8 Adjusting Switch The “DUALBRITE” switch determines the amount of time the lights stay on at a reduced light level after sundown. Switching this setting to “OFF” will not effect the “ON-TIME” setting. Ƒ The “LAMP MODE” switch determines the way the lights will turn on when motion is detected. Set the “DUALBRITE” switch to OFF, 3 hours, 6 hours, or dusk-to-dawn (sunset to sunrise). C Ƒ Security (“NORMAL”) - Light comes on instantly.
Care and Cleaning Ƒ To prolong the original appearance, clean with clear water and a soft, damp cloth only. Ƒ Do not use paints, solvents, or other chemicals on this light fixture. They could cause a premature deterioration of the finish. This is not a defect in the finish and will not be covered by the warranty. Ƒ Do not spray with a hose or power washer. Troubleshooting Problem The light will not come on. The light comes on during the day. The light comes on for no apparent reason.
Troubleshooting (continued) Problem The lights stay on continuously. The lights flash on and off. The lights flash once then stay off in manual mode. Possible Cause Solution Ƒ A bulb is positioned too close to the motion sensor or pointed at nearby objects that cause heat to trigger the light sensor. Ƒ Reposition the bulb away from the motion sensor or nearby objects. Ƒ The motion sensor may be picking up a heat source like an air vent, dryer vent, or brightly painted, heat-reflective surface.
Questions, problems, missing parts? Before returning to the store, call Defiant Customer Service 8 a.m.-6 p.m., EST, Monday-Friday 1-866-308-3976 HOMEDEPOT.COM Retain this manual for future use.
Articulo #703390 703499 Modelo #DF-5416-BK-A DF-5416-WH-A GUÍA PARA EL USO Y CUIDADO LUZ DE SEGURIDAD POR MOVIMIENTO ¿Tiene preguntas, problemas o piezas perdidas? Antes de la devolución al almacén llame a Servicio al Cliente de Defiant 8 a.m.- 6 p.m., Hora del Este, de lunes a viernes 1-866-308-3976 HOMEDEPOT.COM GRACIAS Agradecemos la fe y la confianza que usted ha depositado en Defiant al comprar esta luz de seguridad por movimiento.
Contenido Herramientas Requeridas ....................15 Ferretería Incluida................................16 Contenido del Paquete .........................17 Sitios Para el Montaje ..........................17 Instalación ..............................................18 Operación ................................................19 Cuidado y limpieza .................................22 Análisis de averías .................................22 Contenido ................................................
Especificaciones Alcance Hasta 70 pies (21,3 m) – Varía con la temperatura circundante Ángulo de detección Hasta 180° Carga eléctrica-Incandescente Hasta 240 vatios máximo (Hasta 120 vatios máximo por cada porta-bombillas) Carga eléctrica- estabilización incorporada CFL (SBCFL) Hasta 60 vatios máximo PAR 38 luz reducible SBCFL (Hasta 30 vatios máximo por cada porta-bombillas) - Clasificada para uso exterior.
Antes de la instalación (continuación) FERRETERÍA INCLUIDA NOTA: La ferretería se muestra en su tamaño real AA BB CC DD GG Pieza EE HH FRONT Descripción Cantidad AA Capuchón para cable 3 BB Tapón de caucho 1 CC Tornillo de montaje 1 DD Tornillo del soporte de montaje 2 EE Tornillo del soporte de montaje 2 FF Tornillo del soporte de montaje 2 GG Empaque (no está a escala) 1 HH Soporte de montaje (no está a escala) 1 Colgador plástico (no está a escala) 1 II FF 16 II
Antes de la instalación (continuación) CONTENIDO DEL PAQUETE A B A D D C Pieza Descripción Cantidad A Porta bombilla 2 B Escudete 1 C Detector de movimiento 1 D Casco 2 SITIOS PARA EL MONTAJE Ƒ Determine el sitio para el montaje - una pared o debajo de un alero.
Instalación del soporte de 1 Instalación montaje temporalmente el 2 Cuelgue aparato de luz Ƒ ADVERTENCIA: Desconecte la energía eléctrica en el disyuntor o en el fusible. Coloque cinta aislante sobre el interruptor disyuntor y compruebe que no haya energía eléctrica en el aparato de luz. Ƒ Ƒ Ƒ Retire el aparato de luz existente. Instale el soporte de montaje (HH) con la palabra estampada “FRENTE” en dirección contraria a la caja de conexiones.
Instalación (continuación) alrededor del aparato de los cascos y las 5 Calafatee 6 Instalación de luz bombillas Ƒ Ƒ Calafatee alrededor del escudete (B) y en la superficie de montaje con un sellador de silicona (no incluido) Ƒ Ƒ Ƒ Alinee las tres ranuras del casco (D) con los tres puntas del porta bombillas (A). Inserte el casco (D) en el porta-bombillas (A) y gírelo en sentido horario para bloquearlo. Repita igual con el otro casco (D).
Operación (continuación) del detector para de la zona de 3 Calibración 4 Regulación prueba detección del detector de movimiento Cuando el interruptor de “DURACIÓN” (“ON-TIME”) se fija en la posición “PRUEBA” (“TEST”) el aparato de luz operará durante el día o la noche. La luz permanecerá encendida 5 segundos después que todo movimiento se ha detenido. Ƒ Ƒ Ƒ Ƒ Ƒ Ƒ Fije el interruptor de “DURACIÓN” en la posición “PRUEBA (“TEST”). Fije el interruptor “DUALBRITE” en la posición “APAGADO” (“OFF”).
Operación (continuación) del interruptor 7 Regulación DUALBRITE del interruptor 8 Regulación FASE LÁMPARA El interruptor DUALBRITE determina el lapso de tiempo que la luz permanece encendida con un nivel de luz reducido luego de la puesta del sol. Cambiando esta calibración a “OFF” (“DESCONECTADO”) no quedará afectada la calibración de la DURACIÓN. Ƒ El interruptor FASE LÁMPARA determina la manera en que las luces se encenderán cuando se detecta movimiento.
Cuidado y limpieza Ƒ Para mantener la apariencia original, limpie solamente con agua limpia y un paño húmedo y suave. Ƒ No use pinturas, solventes ni otros químicos en este aparato de luz. Podrían ser la causa de una prematura deterioración del acabado. Esto no es un defecto del acabado y no será cubierto por la garantía. Ƒ No rocíe con manguera ni con una lavadora eléctrica. Análisis de averías Problema La lámpara no se enciende. La luz se enciende durante el día.
Análisis de averías (continuación) Problema Causa Probable Solución Las luces se apagan demasiado tarde en la calibración crepúsculo-al-amanecer. El aparato de luz puede estar instalado en un sitio relativamente oscuro. Vuelva a ubicar el aparato de luz o utilice la calibración 3 horas o 6 horas. Las luces permanecen encendidas constantemente. Ƒ Una bombilla está demasiado cerca del detector de movimiento o enfocando a objetos cercanos que producen calor y activan el detector de luz.
¿Tiene preguntas, problemas o piezas faltantes? Antes de la devolución al almacén llame al Servicio al Cliente de Defiant de 8 a.m.-6 p.m., Hora del Este, de lunes a viernes. 1-866-308-3976 HOMEDEPOT.COM Guarde este manual para uso futuro.