Deako Smart Dimmer Single Pole Smart Dimmer Master Smart Dimmer Remote Smart Dimmer
Get to know your Deako Switch 2
LED indicators Main button Dimmer control Configure button 3
LED key LED COLOR 4 WHAT IT MEANS Blinking green Powering up Blinking purple Linking mode Blinking blue Pairing mode Blinking white Pairing or Linking
LED COLOR WHAT IT ME ANS Solid white Pairing or Linking successful Blinking red Error occured, try again Solid red Factory resetting 5
How many switches control this light? 6
1 switch 2+ switches If one switch controls this light, CONTINUE TO PAGE 8 If two or more switches control this light, TURN TO PAGE 12 7
Insert a switch 1 8 Align the blue tab on the backplate with the top of the switch
2 While pressing the switch inwards, push in the blue tab 9
Installation complete! Now let’s get smart.
Pairing Control your new smart switch by downloading the Deako App.
What you’ll need 12
1x master dimmer 1+ remote dimmer One master dimmer One remote dimmer for each additional switch location 13
Switch types Identify the switch type by looking at the sticker found on the back of your switch. You will either have a Master Smart Dimmer or Remote Smart Dimmer. If you have a different type of switch, go to support.deako.
9696669209165087 9696669209165087 15
Remove existing dimmer 1 16 If there is a switch installed in the backplate you want to upgrade, start by pulling the corner of the faceplate
2 Pull the blue tab outwards to release the switch 17
Insert Remote Dimmer 3 Locate the powered backplate in the circuit by inserting a Remote Smart Dimmer into a backplate in the circuit Align the blue tab on the backplate with the top of the switch 18
4 While pressing the switch inwards, push in the blue tab If the backplate is powered, the switch will flash green If switch does not flash green, move to the next location & repeat step 1 19
5 20 Wait until the switch stops flashing green, then press & hold the configure button until it flashes purple
6 Move to the next powered backplate, then repeat steps 1-5 for each switch in the circuit until you get to the last switch 21
Insert Master switch 7 22 On the last switch in the circuit, insert the Master Smart Dimmer
8 Wait until the switch stops flashing green, then press & hold the configure button until it flashes purple Once all switches in the circuit are flashing purple, continue to step 9 23
9 Once all switches in the circuit are flashing purple, press & hold the configure button on any switch until it flashes white Once the switches show solid white and turn off, linking is complete 24
10 To test if they’ve been successfully linked, press each switch to confirm that they control the light Now you’re ready to pair your switches with the Deako App 25
Troubleshooting • • • • 26 Linking is only required for 3-way and 4-way wiring configurations If at any point a switch blinks red, factory reset it and try again To exit linking mode at any point, press & hold the configure button for 10 seconds to factory reset each switch before retrying If you have dead-end or other nontraditional wiring in your home, you can find wiring and setup instructions at deako.
Factory reset Press & hold the configure button for 10 seconds (the LED will be appear solid red).
FCC Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
IC Statement -English: This device contains licence‐exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation of the device.
Need help? support.deako.