5713216831/06.
BEAN TO CUP ESPRESSO AND DE CAPPUCCINO MACHINE Instructions for use GB ESAM 2200/ ESAM2600/ESAM2800
2
A6 A3 A4 A5 A7 A2 A1 A8 A21 A20 A9 A19 A10 A18 A12 A17 A13 A14 A16 A23 A15 B2 B4 B6 B7 B1 B3 B8 B11 B5 B9 B12 B13 B14 3 B15 B10 A11
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 4
16 20 17 18 21 22 5 19 23
CONTENTS SETTING WATER HARDNESS.................. 15 Measuring water hardness............................... 15 Set water hardness.......................................... 16 INTRODUCTION...................................7 Symbols used in these instructions .................. 7 Letters in brackets............................................. 7 Troubleshooting and repairs.............................. 7 Setting the temperature................. 16 TECHNICAL SPECIFICATION................... 16 SAFETY....
INTRODUCTION SAFETY Thank you for choosing the ESAM2 Bean to cup coffee maker. To get the best result of your new coffee machine please readthese instructions carefully before use. This should ensure optimum results and maximum safety. Fundamental safety warnings Danger! This is an electrical appliance and may therefore cause electric shock. You should therefore follow the following safety warnings: • Never touch the appliance with damp hands or feet. • Never touch the plug with damp hands.
DESIGNATED USE DESCRIPTION This appliance is designed and made to prepare coffee and heat drinks. All other use is considered improper. This appliance is not suitable for commercial use. The manufacturer is not liable for damage deriving from improper use of the appliance. This is a household appliance only.
Using the coffee maker for the first time B12. light: grounds container full B13. light: general alarm B14. Rinsing or descaling button with light B15. ECO energy saving mode button with light Please note: Coffee has been used to factory test the appliance and it is therefore completely normal for there to be traces of coffee in the mill. The machine is, however, guaranteed to be new.
tion of this cycle. 15min Danger of burns! During rinsing, a little hot water comes out of the coffee spouts and is collected in the drip tray underneath. Avoid contact with splashes of water. 30min 1h 2h 3h . 3. Press the ECO button to confirm the selection and return to normal use of the appliance. Auto-off is programmed. • To turn the appliance on, press the button (fig. 4). The and lights flash while the appliance is heating up and performing an automatic rinse cycle.
Selecting the quantity of coffee in the cup Select the required quantity of coffee by turning the knob. • nal circuits of the appliance and thus raising the coffee temperature. warm the cups by rinsing them with hot water (using the hot water function). Making coffee using coffee beans Important! Do not use caramelised or candied coffee beans as they could stick to the coffee mill and make it unusable. Turning it clockwise increases the amount of coffee obtained.
• damage the appliance. Never use more than one level measure or it could dirty the inside of the machine or block the funnel. 6. Turn the steam knob to the I position. Steam is delivered from the cappuccino maker, giving the milk a creamy frothy appearance and making it more voluminous; 7. For a creamier froth, rotate the container with slow movements in an upward direction. (You should not discharge steam for more than 3 minutes at a time); 8.
CLEANING 2. Wait for a few minutes for the cappuccino maker to cool down. Grip the handle of the cappuccino maker tube firmly in one hand and with the other rotate the cappuccino maker anticlockwise (fig. 14) and remove by pulling downwards (fig. 15). 3. Wash all parts of the cappuccino maker thoroughly with a sponge and warm water. 4. Make sure the holes shown by the arrows in fig. 16 are not blocked. If necessary, clean with a pin. 5.
Cleaning the drip tray Cleaning the pre-ground coffee funnel Check regularly (about once a month ) that the pre-ground coffee funnel (A6) is not blocked. If necessary, remove coffee deposits with a brush. Important! If the drip tray is not emptied regularly, the water could overflow from the edge and seep inside or around the machine. This could damage the machine, the surface it rests on or the surrounding area.
red buttons have snapped out. 8. Close the infuser door. 9. Replace the water tank. DESCALING Descale the appliance when the panel flashes. forms a series of rinses and pauses to remove limescale deposits from inside the machine. After about 30 minutes, the water tank is empty and the light comes on. Turn the steam knob a half turn clockwise as far as it will go. The appliance is now ready for rinsing through with clean water. 11.
Level 3 • • Level 4 Set water hardness 1. Make sure the appliance is off (but connected to the mains electricity supply and with the main switch in the I position); 2. Press and hold the button for at least 6 seconds. The lights come on; 3. Confirm the selection by pressing the button. 4. Turn the selection knob and set the level shown by the indicator paper (see previous paragraph). 5. Press the button to confirm the setting. 6. Press the button to exit the menu.
MEANING OF LIGHTS DURING NORMAL OPERATION LIGHTS 1 DESCRIPTION MEANING The lights flash The water is not yet at the ideal temperature.
1 2 LIGHTS 3 1 DESCRIPTION MEANING WHAT TO DO The light is on ste- The grounds container is Empty the grounds container and drip tray, clean and replace (fig. full or missing adily 23). Important: when removing the drip tray, the grounds container MUST be emptied, even if it contains few grounds.
TROUBLESHOOTING Below is a list of some of the possible malfunctions. If the problem cannot be resolved as described, contact Customer Services. PROBLEM POSSIBLE CAUSE SOLUTION The coffee is not hot • The cups were not preheated. • Warm the cups by rinsing them with hot water (N.B. you can use the hot water function). • The infuser has cooled down because 2/3 minutes have elapsed since the last coffee was made. • Before making coffee, heat the infuser by pressing the button.
Electrical requirements Before using this appliance ensure that the voltage indicated on the product corresponds with the main voltage in your home, if you are in any doubt about your supply contact your local electricity company. The flexible mains lead is supplied connected to a B.S. 1363 fused plug having a fuse of 13 amp capacity. Should this plug not fit the socket outlets in your home, it should be cut off and replaced with a suitable plug, following the procedure outlined below.