DOUBLE SIDE BURNER/GRIDDLE GDSBE1-30 Models INSTALLATION GUIDE US CA 592076A 11.
SAFETY AND WARNINGS ! WARNING! Electric Shock Hazard Failure to follow this advice may result in electric shock or death. ! DANGER IF YOU SMELL GAS • Shut off gas to the appliance. • Extinguish any open flame. • Open lid. • If odor continues, keep away from the appliance and immediately call your gas supplier or your fire department.
SAFETY AND WARNINGS ! WARNING! ! WARNING! Hot Surface Hazard Failure to follow this advice may result in fire, burns, scalds or personal injury. Explosion Hazard Failure to follow this advice may result in injury or death • Accessible parts may become hot during use. • If you smell gas, do not use the appliance. • When in use, do not touch the burner, grate, or immediate surrounding area as these areas become extremely hot. Clean the with caution.
SAFETY AND WARNINGS zz zz Do not store a full LP tank in direct sunlight. After a period of storage or non-use, the appliance should be checked for gas leaks, deterioration, proper assembly, and burner obstructions before use. Gas requirements zz zz General Use zz zz zz zz zz zz zz zz zz zz zz zz zz zz zz zz zz zz zz zz zz zz zz zz zz This appliance is not intended to be installed in or on recreational vehicles, trailers or boats.
PRODUCT DIMENSIONS j k k g l f a D e h I b FRONT PROFILE PRODUCT DIMENSIONS INCHES MM 10 1/2 266 30 762 C Overall depth (excluding dials) 26 7/8 683 D Depth of chassis 22 5/8 574 27 13/16 707 9 15/16 252 9/16 14 H Depth of control panel to front of chassis 2 1/16 52 I Depth from control panel to rear of product 25 1/2 648 J Depth of lid 23 585 K Width of lid 14 3/8 365 L Height of lid 1 11/16 43 A Overall height (excluding burners and pan supports) B Overall width
CUTOUT DIMENSIONS STANDARD CUTOUT INSULATED JACKET CUTOUT If the unit is to be placed into a combustible enclosure, an insulated jacket is required.
CLEARANCES Clearances to non-combustible construction Material which is not capable of being ignited and burned, such as materials consisting entirely of, or a combination of, steel, iron, brick tile, concrete, slate, and plaster. The side burner/griddle is designed for easy placement into builtin masonry enclosures. For non-combustible applications the unit drops into the opening and hangs from its side flanges. A deck is not required to support it from the bottom.
CLEARANCES Clearances to combustible construction Any materials of a building structure or decorative structure made of wood, compressed paper, plant fibres, vinyl/plastic or other materials that are capable of transferring heat or being ignited and burned. Such material shall be considered combustible even though flame-proofed, fire-retardant treated or surface-painted, or plastered. Do not use this appliance under unprotected overhead combustible surfaces.
ELECTRICAL CONNECTION All units are supplied with a 12V power transformer to operate the products ignition and dial illumination features. The transformer is sealed in a box with an attached power supply cord. Electrical requirements Use only a Ground Fault Interrupter (GFI) protected circuit with this product.
GAS CONNECTION GAS REQUIREMENTS Verify the type of gas supply to be used, either natural or LP, and make sure the marking on the appliance rating plate agrees with that of the supply. The rating plate is located on the underside of the drip tray. Never connect an unregulated gas line to the appliance. You must use a gas regulator even if the supply is controlled. Gas conversion kits are available from Customer Care.
GAS CONNECTION CART LP CONNECTION BUILT-IN LP CONNECTION Units set for use with LP gas come equipped with a high capacity hose/regulator assembly for connection to a standard 20 lb. LP cylinder (Type 1). The LP tank is not included. The system is leak tested, do not remove the Regulator/Hose assembly from the product during cart installation. Connection: 1/2” NPT female with 3/8” flare adapter. Operating pressure: 11.0” W.C. Supply pressure: 12” to 14” W.
LEAK TESTING A complete gas tightness check must be performed at the installation site. Periodically check the whole system for leaks, or immediately if the smell of gas is present. Testing for leaks Removing the valve panel Prepare soap solution by combining one part liquid detergent and one part water. Pour into a spray bottle. Ensure all control valves are in the OFF position before turning the gas supply ON. 1 1 Remove all dials by pulling outwards.
LOW FLAME ADJUSTMENT The valves on the double side burner/griddle unit feature an adjustable low setting. Due to fluctuations in gas pressure, or heating value you may feel it necessary to increase or decrease gas flow in the low position. If the gas type has been converted from natural to LP or vice-versa, the low flame setting must be reviewed and adjusted. 1 2 Push in and hold the selected dial for two seconds before turning to HI. Hold for 10 seconds to light the selected burner.
FREESTANDING CART INSTALLATION (OPTIONAL) Designed with flexibility in mind, the 30” double side burner/griddle can be either built-in or mounted on a freestanding cart. If the unit is to be placed onto a freestanding cart, an approved DCS cart is required and can be purchased separately from your local DCS dealer.
INSTALLER CHECKLIST IMPORTANT! Read all installation instructions in this manual to see if the unit has been correctly installed. Ensure that installation has been completed correctly before use.
DCSAPPLIANCES.COM © Fisher & Paykel Appliances 2019. All rights reserved. The product specifications in this document apply to the specific products and models described at the date of issue. Under our policy of continuous product improvement, these specifications may change at any time. You should therefore check with your Dealer to ensure this document correctly describes the product currently available. US CA 592076A 11.
