Use and Care Manual

DETAILED INSTRUCTIONS
stick, being sure to stir from the bottom up to disperse any settled material at the bottom
of the can. A drill mixer attachment is also an excellent stirring option.
APPLICATION: The surface must be clean, dry, in good repair and pre-coated with the
enclosed Primer Coat from step one. Two applications of the Stone Coat must be applied.
Allow at least 4 - 6 hours between coats (longer in cool or damp conditions).
COAT ONE: (1) Use the 1” brush from the kit to apply Stone Coat into corners, along
edges and tight areas, around faucets, etc.
Brush it down at, thin and smooth. 2) Use
the enclosed 4” brush to continue application
across the raised backsplash piece (if present)
and the rest of the countertop. Apply a at,
uniform coat about 1/16” thick. Pass the
brush over the wet material a few times to
make smooth. 3) To apply over the bull nose
or at front edge of the counter, just follow the
contours with your brush.
COAT TWO: (1) Use the 1” brush from the kit
to apply Stone Coat into corners, along edges
and tight areas, around faucets, etc. 2) Use the
enclosed plastic smoother to spread on the
LuxROCK. Press rmly to spread it on thin
and uniform across the raised backsplash
piece (if present) and the rest of the countertop.
This will create a smooth even coat that lls any
indentations, resulting in a far easier sanding
step which follows.
SAND AND CONDITION THE STONE: With
your second coat of LuxROCK smoothly applied
and cured for 24 hours, it’s time to sand
and condition the stone. 1) Use the enclosed
120 grit sandpaper, followed by the 180
grit sandpaper to shave away any signicant
roughness or bumps and polish the overall
surfaces of the backsplash, front edges and
remaining at countertop surfaces. When done,
the raw stone layer should be smooth and even
beneath your hand. NOTE: There will still
be some very light texture even when
sanding is complete, which is normal.
This will be covered by the following epoxy layer. 2) Sanding can be done by hand, but
using a random orbital sander is highly recommended for easiest and fastest
results. Connect the sander to a vacuum if possible to minimize any dust
during use. 3) For the raised backsplash and front edges, the enclosed sanding sponge
can be used to smooth out any rough bits by hand to ensure smoothly contoured edges
and verticals. 4) After vacuuming the surface, wipe it down several times with a clean,
very damp (not dripping wet) rag to pick up any remaining ne dust. Failure to remove
loose dust may result in a clouded nal nish. 5) Roll a thin coat of LuxROCK Stone
Conditioner across the sanded surface. Use rm rolling pressure to maximize coverage
for this step. This will create an optimal dust-free application surface for the StoneSet
Epoxy. 6) Let the Stone Conditioner dry on the surface at least two hours before
application of StoneSet Epoxy.
StoneSet is a 2-part penetrating epoxy formula that integrates with your
new stone layer to maximize hardness and smooth feel.
MIXING COMPONENTS: Keep in a cool place prior to use for maximum pot
life. PARTS MUST BE FULLY BLENDED FOR THREE MINUTES BEFORE APPLICATION.
Pour full contents of “Part-B” into “Part-A” in original packaging or other suitable mixing
container. Use the enclosed stir stick. After mixing the parts together, immediately
pour into a clean paint tray. DO NOT leave mixed epoxy in the can during use as this
will decrease pot life, becoming very warm and less workable. Ideally, mixed epoxy
should be applied within 30 minutes or less.
**IMPORTANT: USE ONE FULL STONESET EPOXY KIT PER 20 SQ.FT. for a
thicker, self levelling application. **
APPLICATION: Follow all safety recommendations
on cans during use. The surface must be smoothly
sanded, dust free and conditioned before application
of StoneSet. 1) Use the 1” brush from the kit to brush
the coating into corners, along edges and tight areas.
Brush or roll a uniform coat across the attached raised
backsplash if applicable. Brush out any pooled coating
at the bottom of the backsplash. 2) For the remaining
at top, pour two generous beads of epoxy along the
length of the counterop and then use the enclosed low
nap 4” roller to gently distribute and roll out the epoxy
evenly across the surface. Take care not to press hard or
roll quickly which will and overwork the coating and may introduce excessive bubbles into
the clear coat. For the front edge of the counter, roll on a thin coat of the epoxy down and
along the botton of the edge so that everything is evenly coated. 3) Softly blend out any
lines or non-uniform looking wet coating and let everything settle out. Don’t worry about
any very small bubbles or imperfections that may remain. They will be removed in the
following step. 4) Periodically run the brush or roller along the bottom of the front edges
to remove any hanging droplets before they harden. 5) Let the StoneSet coat cure for 24
hours prior to proceeding.
Top Clear is the last step of the LuxROCK
™
Kit. It adds an appealing stain
and wear-resistant semi-gloss shield to your new stone surface.
MIXING: Top Clear must be thoroughly and gently stirred. DO NOT SHAKE.
SURFACE PREPARATION: The previously applied StoneSet epoxy coat must be wet
sanded prior to application of Top Clear. This is an easy and important step that removes
any pimples and other imperfections and prepares the surface for the nal clear coat step
that comes next. Use the enclosed dust mask while sanding. 1) Use the included
misting spray bottle to wet the countertop surface lightly and uniformly prior to sanding
and continue misting as you go. This will eliminate dust and lubricate the surface for
smoothest polishing. 2) Though you can perform this step by hand, we recommend using
a random orbital sander with the enclosed 400-grit sanding disk for easiest and
best results. Use the same 400 grit sanding disc to wet sand the countertop edges and
small backsplash by hand. 3) This step is faster and easier than it sounds. Just shave off
any visual aws and run your hand over the
surface to ensure it is free of protruding
bumps and textural blemishes. 4) When
complete, wash the surface with a wet lint-free
cloth until there is no dust residue visible on
the cloth or your hand. 5) Do a nal wipe of the
dry, clean surface with a lint free cloth to ensure
there is no dust you can feel under your bare
hand before proceeding.
APPLICATION: 1) Pour Top Clear into a
clean paint tray. 2) Use the enclosed one-inch
brush for tight areas as well as corners, along
edges, etc. Avoid pooling of the clear coat at
the bottom of the backsplash during application. 3) Apply Top Clear over the rest of the
countertop with one of the enclosed six-inch rollers. Apply a uniform wet coat, working
in two or three foot sections. Roll in one direction, (not back and forth) with long gentle
strokes using light roller pressure to avoid air bubbles. Softly cross-roll over the wet clear
coat once or twice for nal softening and uniformity. 4) Repeat these steps over the
reminder of the surface until complete. DO NOT DISTURB TOP CLEAR AS IT ATTEMPTS TO
DRY. Wash the roller after use. 5) Let Top Clear dry for 2 - 3 hours and then apply a second
coat in the same manner as the rst and allow it to cure for 24 hours. 6) With everything
dry and cured the following day, use a sharp utility knife to cut around the edges
of the sink and faucet hardware for clean and easy removal of masking tape.
7) If necessary, apply a bead of clear silicone caulking around the sink perimeter and
faucets to guard against water intrusion.
With these steps completed as directed, your project is complete. Congratulations!
SURFACE PREPARATION: The surface must be clean, dry and in good repair.
1) If applying to laminate, the surface must be washed and degreased thoroughly.
2) If applying to a wood tabletop or concrete, the surface must be clean. If a previous
coating exists, it must be in sound condition or otherwise must be removed. 3) For tile
countertops, apply one thin coat of DAICH ElastoLock
®
as an intermediate bonding coat.
4) Protect adjoining surfaces (cabinets, xtures,etc.) with painter’s tape, plastic or old
newspaper. 5) Protect the oor around the countertop area with heavy cardboard
or a drop cloth. 6) If installing LuxROCK around the existing sink edge and faucet
xtures, mask cleanly around all edges, to guard against coating contact. 7) For easiest
installation, we recommend lifting up a few inches – or removing – the sink and faucet
xtures prior to LuxROCK installation for completely open access. The sink and faucets
can be dropped back down and refastened over top of your new stone surface — just
like any other professional countertop installation.
The Primer Coat – is the rst step of your new LuxROCK
™
nish. It
adheres well to laminate, wood, concrete and Daich Coatings ElastoLock
®
and creates an optimal bonding surface.
APPLICATION (Stir before use) 1) Use the 1” brush
from the kit for tight areas as well as corners, along
edges, etc. Wash the brush after use. 2) Roll one thin,
uniform coat of Primer over the entire countertop
with the enclosed 4-inch roller. Wash the roller after
use. 3) Spot-apply Primer to any thin or missed spots
areas. 4) Let the surface dry for one to two hours before
proceeding with the next step.
The Stone Coat is the main component of the LuxROCK Finish System.
Its stone composition brings both strength and stunning granite
elegance to your surface.
MIXING: Prior to use, the Stone Coat must be mixed thoroughly. Use the enclosed stir
Cutting foods: Though your
new surface is durable, use a
cutting board for food prep.
Hot Objects: Your new
surface is heat resistant.
However, to be safe, use a
trivet for added protection.
Maintenance: Keep your surface
in good condition by wiping it
clean after use with a damp cloth or
common household cleaner.
For LIVE footage of the steps shown here, visit us at www.daichcoatings.com
or call 1-866-463-2424. Thank you – and enjoy your new LuxROCK
®
Surface!
CARE TIPS...
Welcome to LuxROCK, the revolutionary new stone coating system
that delivers a whole new way to enjoy authentic, luxuriously smooth
stone countertops, tables and more — at a fraction of the cost!
™
LX-INST-8/2023
**Follow these directions carefully for best results — and also
follow safety precautions on all coating containers during use.