Installation Instructions Modernist Pro Range DOP48M96D/DOP36M94D Part No.
Contents Before You Begin 3 Important Customer-Assurance Information 3 3 Important Safety Instructions 4 Read All Instructions Before Using This Manual Appliance Symbols Used In This Manual About the Anti-tip Device Installation-Related Safety Instructions 4 4 4 5 Product Specifications 10 What Is Included (DOP48M96) What Is Included (DOP36M94) Needed Tools and Parts 10 11 12 Installation Requirements 13 Pre-Installation Checklist General Requirements Location Requirements Gas Requirements Spe
Before You Begin Important Overall design/accessories may differ with the model. Installer • Read this manual before installing the cooktop. • Remove all packing material before connecting the electric and gas supply. • Observe all governing codes and ordinances. • Leave this manual with the owner, and write the unit's model/serial #s inside for easy reference. Installation of this appliance requires basic • mechanical skills. • The owner shall see to the range's proper installation.
Important Safety Instructions READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE • • • To avoid property damage/personal injury/death, follow the directions in this manual. Electrical and gas equipment with moving parts can be dangerous. The Important safety instructions in this manual are intended to minimize the risk of property damage, personal injury, and death. Read these instructions. Keep this manual in a handy place for reference.
Important Safety Instructions Installation-Related Safety Instructions This section consists of general and specific safety instructions surrounding the range's installation. WARNING Read these instructions thoroughly to reduce risk of property damage, fire, personal injury, and death, and to ensure proper installation. General Safety • Do not touch the range during or immediately after cooking. • Know where and how to shut off/on the range's gas-supply valve. • Use only dry pot holders.
Important Safety Instructions Installation-Related Safety Instructions, cont. This section consists of general and specific safety instructions surrounding the range's installation. WARNING Read these instructions thoroughly to reduce risk of property damage, fire, personal injury, and death, and to ensure proper installation. Gas Safety If you smell gas: • do not use the range, and close the gas valve. • do not light a match, candle, or cigarette. • do not turn on any gas or electric appliances.
Important Safety Instructions Installation-Related Safety Instructions, cont. This section consists of general and specific safety instructions surrounding the range's installation. WARNING Read these instructions thoroughly to reduce risk of property damage, fire, personal injury, and death, and to ensure proper installation. Installation Safety • The range should be installed/grounded/serviced by a qualified installer as instructed in this manual.
Important Safety Instructions Installation-Related Safety Instructions, cont. This section consists of general and specific safety instructions surrounding the range's installation. WARNING Read these instructions thoroughly to reduce risk of property damage, fire, personal injury, and death, and to ensure proper installation. Cooktop Safety • Turn all burners off if not using the range. • Do not line the grates or any part of the cooktop with foil.
Important Safety Instructions Installation-Related Safety Instructions, cont. This section consists of general and specific safety instructions surrounding the range's installation. WARNING Read these instructions thoroughly to reduce risk of property damage, fire, personal injury, and death, and to ensure proper installation. Oven Safety • Do not use the oven for non-cooking purposes such as drying clothes or storage. Use the oven for cooking purposes only.
Product Specifications What Is Included (DOP48M96D) The range comes with brass and porcelain burner caps to suit customer preference. Grates (3) Burner heads (6) and Burner caps (7) Griddle (1) Convection filter (3) Temp.
Product Specifications What Is Included (DOP36M94D) The range comes with brass and porcelain burner caps to suit customer preference. Grates (2) Burner heads (4) and Burner caps (5) Wire rack (1) Convection filter (2) Temp.
Product Specifications Needed Tools and Parts Parts Needed Gas line shut-off valve Flexible metal appliance connector ½ in (ID) x 5 ft Flare union adapter ¾ in (NPT) x ½ in (ID) 135-degree elbow (optional) Lag bolt or ½-in (OD) sleeve anchor Flare union adapter ½ in (NPT) x ½ in (ID) Tools Needed Flat-blade screwdriver Phillips screwdriver Open-end or adjustable wrench Pipe wrench (2) Nut driver Pencil and ruler Level Pipe joint compound Utility knife Soapy water solution 12 English
Installation Requirements Pre-Installation Checklist 1. Before installing the range, read this manual thoroughly. 2. Plan for a location where the range will not be subject to strong drafts. 3. Remove packaging, grate boxes, regulator with literature, and literature package from the range, verify that all items are present before beginning the installation. General Requirements Clearances and Dimensions • For OTR over gas stove, follow the local gas code.
Installation Requirements Product Dimensions—Product tolerances: ±1/16” (±1.6 mm) DOP36M94D: 35 7/8” (91.1 cm) wide ; DOP48M96D: 47 7/8” (121.6 cm) 48” (121.9 cm) 28 1/8” (71.4 cm) 27 1/2” (69.9 cm) 26” (66.0 cm) 23 15/16” (60.8 cm) Front of open door Front of handle Front of bull nose Front panel Rear of oven door 15/16” (2.4 cm) top of trim to top of grates (cooking surface) 36 1/8" (91.8 cm) 24” (61.0 cm) 29 7/8” (75.9 cm)*** Back of control panel Cabinet face Countertop height: 36 3/16" (91.
Installation Requirements Cabinet Dimensions Maintain all max/min dimensions and clearances in the diagrams below for safe use. CUTOUT DIMENSIONS Range Model A B C DOP36M94D 42” (106.7 cm)*; 36” (91.4 cm)** 36” (91.4 cm)**; 36 1/8” (91.7 cm)*** 33 1/2” (84.8 cm) DOP48M96D 54” (137.2 cm)*; 48” (121.9 cm)** 48” (121.9 cm)**; 48 1/8” (122.2 cm)*** 43 1/2” (110.5 cm) *Recommended, **Minimum, ***Maximum A 3/8" (1.0 cm) min. flat countertop overhang 13” (33.0 cm) max.
Installation Requirements Location Requirements DOP48M96D (rear) 8 1/8" (20.6 cm) Gas Inlet 26 5/8" (67.6 cm) Shown with electrical access cover removed 6 5/8" (16.8 cm) E - Electrical wiring access hole in bottom 5 1/2" (13.9 cm) DOP36M94D (rear) 11 3/16" (28.4 cm) Gas Inlet 24 1/4" (61.6 cm) Shown with electrical access cover removed 6 5/8" (16.8 cm) 8 7/8" (22.5 cm) 16 English 1. Measurement with appliance legs adjusted to lowest height. 2.
Installation Requirements Gas and Electrical Service • See below for the recommended location of the gas inlet and electrical junction box/receptacle. Existing utilities may be used if they are compatible with this range. Check local building codes for allowed gas-valve locations. • An external manual shut-off valve must be installed between the gas inlet and range so the range's gas supply can be turned on/off.
Installation Requirements Gas Requirements Provide Adequate Gas Supply This oven's installation must conform to local codes or, in their absence, with the National Fuel Gas Code, ANSI Z223.1/NFPA 54. This range's cooktop is designed to operate at a manifold pressure of 5 in. (13 cm) of water column for natural gas/natural gas at high altitude (NG-H) or 10 in. (25.4 cm) of water column for LP (propane)/LP at high altitude (LP-H). Verify that the oven is right for the provided gas service.
Installation Requirements Electrical Requirements Follow these directions to reduce risk of property damage, personal injury, or death. WARNING The owner shall ensure that the electrical service meets requirements and that the electrical outlet is installed by a licensed electrician. All Ranges • Do not use an extension cord or adapter plug with this range. • This range must be plugged in to a properly grounded outlet. (Check with a qualified electrician if you doubt that the outlet is properly grounded.
Installation Instructions Preparing for Installation WARNING • • If the gas or electric service provided does not meet the product specifications, do not proceed with the installation. Call the dealer, the gas supplier or a licensed electrician. Before installing the range, you must locate and secure the anti-tip bracket to the floor. Unpacking the Range Unpack the parts box and verify that all required components have been provided.
Installation Instructions Floor-Mounting the Anti-Tip Bracket, cont. • Determine the required position of the anti-tip bracket, based on the diagram below. Mark the 4 mounting-hole locations on the floor with a pencil. • Determine the screw size. The minimum full thread depth (portion of screw threaded into wood/slab) is 3/8” (1 cm) for wood and 5/8” (1.6 cm) for concrete. (See SCREW SIZE table, below, for correct screw sizes.) Attaching the Bracket to a Concrete Floor 1. Drill four 3/8” dia.
Installation Instructions Installing the Anti-Tip Bracket and Foot, cont. Wall-Mounting the Anti-Tip Bracket For this option to be suitable, the range front panel must be 26 1/2" (67.3 cm) or less from the wall, and the bracket screws must be able to engage the base plate inside the wall. Notches on the sides of the bracket indicate the minimum height of the base plate and that any floor covering thickness will not impede secure threading.
Installation Instructions Preparing for Installation, cont. Wall-Mounting the Anti-Tip Bracket, cont. This hole lines up with bracket center line #12 x 1 3/4” screw, 4 places Back wall Range center line Bracket center line C C Range front panel C ANTI-TIP BRACKET PLACEMENT Dimension DOP36M94D DOP48M96D C 14 1/8” (35.9 cm) 3 1/2” (8.9 cm) Removing the Oven Door WARNING • Do not try to disengage the hinge catches with the door(s) removed.
Installation Instructions Removing the Oven Door, cont. Door Gripping Points 3. Lift the oven door to about a 15° angle from vertical. 4. With both hands, grasp the door just below the handle, and pull up slightly. 5. On the bottom-right edge of the door, pull out the wire connector, and disconnect the wires. 6. Lift the door away from the oven. Electrical Connection CAUTION For personal safety, do not use an extension cord with the range.
Installation Installation Instructions Instructions Installing the Flexible Conduit Remove the conduit connection plate from the rear of the drawer body, and flip it as shown. (Use the 1⅛" hole.) 1⅛" 1⅜" 1⅜" 1⅛" 1. Prepare the conduit cord (Figure 1). 2. Install the conduit cord (Figure 2).
Installation Instructions Installing the Flexible Conduit, cont. Installing a 4-wire conduit • Aluminum building wire may be used but it must be rated for the correct amperage and voltage. Connect wires according to this Step 4 depending on the number of wires. • Wire used, location and enclosure of splices, etc., must conform to good wiring practices and local codes. Ground strap Ground plate Black White Red Wire tips White Black Neutral terminal Red 1.
Installation Instructions Gas Connection, cont. Regulator connection Gas line Before sliding the range into the cabinet 1. Turn off the gas-supply valve, and turn off power to the range. 2. Connect a flexible gas line to the shut-off valve installed on the stub out. The line must be long enough that the range can be pulled out for service without disconnecting the line. 3. Slide the gas line up through the chassis' access holes to the regulator.
Installation Instructions Reinstalling the Oven Door(s) WARNING To avoid personal injury or damage to the door from it falling off its hinges: • • Make sure that the notch on the bottom of each hinge rests on the lower lip of each hinge receptacle before trying to open the oven door. Flip the hinge locks toward the front of the range immediately after installation of the door. 1. Grasp the oven door on both sides, and hold it at a 15° angle from the front of the oven.
Installation Instructions Adjusting the Door (DOP48M96D only), cont. NOTE Lifting the door-hinge latches too much makes fastening the two screws difficult. To adjust door side to side, turn the upper bolt (see left). Installing the Burner-Control Knobs WARNING Installing the range knobs in the wrong position may result in damage to the griddle included with the range. The knobs for the center burners are marked with the maximum griddle settings.
Installation Instructions Rangetop Assembly Assembling the Burners CAUTION • • • Do not operate the rangetop burners unless properly assembled. Do not push in a rangetop knob while removing the burner; a slight electrical shock might result. Do not remove the top or touch a burner electrode while another burner is on. 1. Place the burner heads on the burner bases as shown at left. (The electrodes fit in the slot in the bottom of the heads.) The heads should be flat and parallel to the rangetop. 2.
Installation Instructions Dual Burner Head/Cap, cont. 3. Match the burner caps to the burners by size, then install the caps on the heads. Round Burner Head/Cap 1. Put the burner heads on the burner bases as shown at left. The bottom of the head fits within the burner base. 2. Turn the head until it drops into place. Twist the head back and forth slightly to ensure it is properly seated. 3. Put the burner caps (brass or porcelain) atop the burner heads.
Installation Instructions SimmerSear Assembly Locating Tab Keyed Hole Burner Head 1. Put the burner heads in place as shown. The locating tab on the burner head goes in the keyed hole as shown. Burner Base Burner Ring 2. Put the burner rings on the burner heads as shown. Match the tabs on the bottom of the ring to the slots on the head. Twist each ring back and forth slightly to verify it is properly seated. Tabs Slots Ridge on Bottom of Burner Cap 3. Put the burner caps on the burner rings.
Installation Instructions Installing the Grates For best results and longest life, install the grates as instructed. When installed properly, the openings in the grates are centered over the burners. The grates occupy specific positions on the rangetop. For maximum stability and safe operation, these grates should only be used in their proper positions. The back of the right grate is notched to help orient the grates correctly. (See the graphic below.) To correctly position the grates: 1.
Installation Instructions Verifying Proper Operation 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. Before starting the test procedure, turn off all burners, and see that all burner components and grates are properly positioned. Open the gas-supply valve, and check for gas leaks. Turn on power to the range at the circuit breaker or fuse box. Use the oven display to set user preferences and wireless network settings. On the display, tap MENU > BAKE. (The default bake temperature should appear.) Tap Start.
Installation Installation Instructions Instructions Installation Checklist WARNING The installer should complete this checklist to ensure thorough, proper installation. Proper installation is the responsibility of the homeowner. • Was the plastic sheeting peeled off the range exterior? • Was all packaging removed from the oven chamber? • Do all leveling legs contact the floor? Is the unit level? (Pg. 27.) • Was the range secured with the anti-tip bracket and foot as instructed? (Pgs. 20 – 23.
DG68-00936A-00 Dacor ∙ 14425 Clark Avenue, City of Industry, CA 91745 ∙ Phone: (800) 793-0093 ∙ Fax: (626) 403-3130 ∙ www.dacor.
