Installation Instructions 24 - INCH DISHWASHER Models: ED24, ID24, MDH24, MDV24, PD24AG, PD24BK PD24BU, PD, 24GN, PD24SG, PD24TS Part No. 101891 Rev.
All specifications are subject to change without notice. Dacor ® assumes no liability for changes to specifications. © 2007 Dacor, all rights reserved.
Table of Contents Before You Begin............................................................... 1 Important Safety Instructions........................................ 1-3 Important Information About Safety Instructions............... 1 Safety Symbols and Labels.............................................. 1 General Safety Precautions.............................................. 2 Design Specifications........................................................ 3 Product Specifications......................
Important Safety Instructions General Safety Precautions To reduce the risk of fire, electric shock, serious injury or death when using your appliance, follow basic safety precautions, including the following: Warning 1. Do not install or operate this dishwasher if it has been damaged, dropped, has damaged electrical conduit or wires or is not working properly. If the product is damaged when received, immediately contact the dealer or builder. 2.
Important Safety Instructions CAUTION Keep the factory installed high loop drain hose in place to ensure proper dishwasher operation. Do not cut, tie, strap or lower it. If it is necessary to lengthen it, install an aftermarket drain extension kit, available at most home improvement stores. Design Specifications Product Specifications Technical Water Pressure 20 to 120 psi (138 - 827 kPa) Water Temperature 120°F, minimum Power Requirements 15 A, 120 Vac, 60 Hz dedicated, grounded, circuit.
Preparing for Installation IMPORTANT: Follow all cabinet and countertop minimum dimensions shown below to insure safe operation. warning Observe all governing codes and ordinances during planning and installation. Contact your local building department for further information. Preparing the Location Carefully check the location where the dishwasher is to be installed. Put it in a location with convenient access. Make certain that electrical power can be provided in the selected location.
Preparing for Installation Power Supply Preparation warning The electrical power supply for the dishwasher must be installed only by a licensed electrician as specified below. It is the owner’s responsibility to ensure that the electrical connection of this appliance is performed by a licensed electrician. Plumbing Preparation • The water pressure must be between 20 and 120 psi (138-827 kPa). The household hot water heater should supply a minimum of 120°F water to the dishwasher location for best results.
Installation Specifications Verify the Package Contents NOTE: Model ID24 ships without a front panel. It is designed for the installation of an integrated front panel that matches the surrounding cabinets. • With the assistance of at least one person, remove the dishwasher from the shipping carton. Place the unit to the side of the cabinet opening. • Remove all of the packing materials from inside and outside of the unit.
Installation Specifications warning • Do not install the dishwasher unless the electrical service provided meets the dishwasher specifications (see page 5). • A qualified technician must complete the installation of this built-in appliance. The owner is responsible to make sure the dishwasher is properly installed. Improper connection of the electrical wiring may create an electric shock or fire hazard and may result in damage to the dishwasher’s electrical system.
Installation Instructions Electrical Connection (Continued) 13. Feed the electric wire or cord into the utility hole in the side of the cut-out. Pull all of the slack out of the wire. If the unit is to be connected directly to the house wiring: • With power turned off at the circuit breaker or fuse box, remove the house junction box cover. • Feed the dishwasher wiring into the junction box. Secure the wire with a UL/CSA approved strain relief.
Installation Instructions Plumbing Connections Installing the Unit in the Cabinet 1. Connect one end of the 3/8” flexible braided fill hose to the water supply valve. • Make sure the water valve is off before sliding the unit into the cabinet. 2. Route the hose through the utility access hole in the side of the appliance cut-out. Put the unconnected end of the hose over a bucket. Turn on the water to clean any debris out of the supply line and fill the hose for leak testing. Turn the valve off.
Installation Instructions Installing the Unit in the Cabinet (continued) NOTE: The leg nuts can be removed to make the dishwasher lower. To do so: • Turn the leg until it comes out of the chassis. • Remove the nut from the leg. • Re-thread the leg into the chassis. • Reach inside the chassis and thread the nut onto the top of the leg. 2.
Installation Instructions Drain Line Installation 1. Connect the flexible drain line to the air gap or connect it directly to the waste tee or disposal (see below). 2. For installations without an air gap, put a loop in the drain line as shown. 3. Tighten the holding clamp. For installations with an air gap check to make sure the drain line from the air gap to the disposal/drain trap is complete and that the clamps are tight. Create loop and fasten to under side of cabinet 20" Min.
Installation Instructions Verifying Proper Operation WARNING • To ensure a safe and proper installation, the following checklist should be completed by the installer to ensure that no part of the installation has been overlooked and the unit is working properly. • Proper installation is the responsibility of the homeowner. The importance of proper installation of your Dacor dishwasher cannot be overemphasized.
Notes
Dacor ● 1440 Bridge Gate Drive, Diamond Bar, CA 91765 ● Tel: (800) 793-0093 ● FAX: (626) 403-3130 ● www.Dacor.
