Installation Instructions

ManualsBrandsCustomCraft High Resolution Countertops ManualsBathCustomCraft Countertops® 37"W x 22"D Blue Flower Granite High-Resolution™ Laminate Vanity Top with Drop-In Sink Cut-Out

VANITY TOP INSTALLATION

Before Starting

Tools Required Optional Installation Kit Includes

Helpful Tips

• Color-Matched Caulk — Used as color match nishing caulk to seal area where

loose backsplash meets the vanity top or where the vanity top meets the wall.

We have taken extra steps to package the end splash, helping to ensure that it arrives free from damage. Inspect the vanity

top as soon as possible and prior to any tear out of existing vanity top at the job site. This inspection should take place within

twenty-four hours of pick up. Do not store materials outside or in locations where they may be exposed to water or high

humidity. Installation of a vanity top thought to be either defective or have dimensional error does not extend your warranty to

include installation or reimbursement and may void your warranty. The limited warranty covers replacement or repair only. See

laminate warranty on back of instruction sheet.

• Hammer

• Marking utensil

• Tape measure

• Screw Gun

• Safety Glasses

• Belt Sander

• Phillips-Head Screw Driver

• Square Drive

• Jig Saw Utility Knife

1. Build-up Strips

2. Shims

3. 1-1/4" Screws

4. Color-Matched Caulk

1) 2) 3) 4)

• Check all dimensions, and test-t for proper t and alignment. Any problems should be addressed now to avoid larger

ones later. Take care in removing existing vanity tops (if necessary) so as not to damage the vanity, plumbing, or

electrical wiring.

1A) Frameless Vanities

1. Check to see if the vanity is are level. Adjust vanity if possible, shims may be required

later if vanity can not be adjusted.

2. Measure the width of the build down stick next to the endcap located on the underside of

the vanity top (Fig. 1).

3. Measure in from the end of the vanity the distance of the build down stick plus 1/4" a n d

mark (Fig. 2). Pre-drill the front and back of the build-up strip where it will fasten to

the vanity. Then pre-drill an additional 3 holes of equal distance in the

middle of the build-up strip for screw installation into the bottom of the vanity top. Install

using 1-1/4" drywall screws at marked spots.

4. If applicable, Install a build-up strip on either side of the joint where two vanity meet,

making sure to leave enough room for installation of screws from the bottom

into the vanity top.

5. When installing build-up strips on sink base, measure the opening for the sink to verify

that the build up strip is installed far enough away not to impede the installation of the

sink.

Follow 1A for Frameless Vanities / Overhangs, 1B for Standard Vanities

Additional build-up strips and 1-1/4" screws may be required for

installation on a frameless cabinet system. Additional materials can be

purchased at any Menards

store.

Additional build-up strips may be required for installation on a frameless vanity system. 1x4's can be used as longer

build-up strips.

1) BUILD-UP STRIP / FRAMELESS VANITIES

Fig. 1

All overhangs require build-up strips the full depth of

the countertop for support.

Any overhangs longer than 15" require support to the oor.

Fig. 2

11/16/18

Summary of content (4 pages)

PAGE 1
VANITY TOP INSTALLATION Tools Required Optional Installation Kit Includes • • • • • • • • • 1. Build-up Strips 2. Shims 3. 1-1/4" Screws 4. Color-Matched Caulk Hammer Marking utensil Tape measure Screw Gun Safety Glasses Belt Sander Phillips-Head Screw Driver Square Drive Jig Saw Utility Knife R 1) 2) 3) 4) • Color-Matched Caulk — Used as color match finishing caulk to seal area where loose backsplash meets the vanity top or where the vanity top meets the wall.
PAGE 2
1) BUILD-UP STRIP / STANDARD VANITIES 1B) Standard Vanities 1. Check to see if the vanity is level. Adjust vanity if possible, shims may be required later if vanity can not be adjusted. 2. Pre-drill holes in the front and back of build-up strips. Attach strips to the top of the vanity face and back frame using 1-1/4" drywall screws. Place build-up strips every two feet of the vanity.
PAGE 3
5) ATTACH VANITY TOP TO THE CABINETS (NOTE: Hammer and small block of wood required) Place vanity top in place and fasten (Fig. 6.) using 3 1-1/4" black drywall screws through the build-up strips (using longer screws will result in puncturing the surface of the vanity top). Shims may be required if vanity are not level. Fig. 6 6) CAULK BACKSPLASH (NOTE: Color-matched caulk; included in installation kit sold separately) • Use color-matched caulk to seal around backsplash and walls (Fig. 7).
PAGE 4
LIMITED WARRANTY FOR CUSTOMCRAFT LAMINATE Product Subject to this Limited Warranty This Limited Warranty applies only to the CUSTOMCRAFT LAMINATE (the “Product”) sold by Midwest Manufacturing, a division of Menard, Inc., (the “Company”). Who is Entitled to this Limited Warranty The Company grants this Limited Warranty solely in favor of the original purchaser of the Product (the “Original Purchaser”), but to no other person or entity whatsoever.