Storage Cabinet CF3121
PART LIST A B D C E Top Panel Left Panel Right Panel Cross Rail 1 PC 1 PC 1 PC 1 PC F H G Drawer Front Panel 1 PC K Drawer Left Panel 1 PC L Drawer Right Panel 1 PC M Left Door Panel Right Door Panel 1 PC I 1 PC 1 PC J Drawer Back Panel 1 PC N Back Panel Adjustable Shelf 1 PC 1 PC 2 Bottom Panel Drawer Bottom Panel 1 PC
HARDWARE LIST #1 #2 #3 #4 #5 Ø1/4"*25mm Ø1/4"*11mm Ø1/4"*13mm 4mm*90 Ø8*30mm Bolt Spring Washer Flat Washer Allen Wrench Wood Dowel 1 PC 12 PCS (Extra 1) #10 10 PCS (Extra 1) 10 PCS (Extra 1) 10 PCS (Extra 1) #6 #7 #8 #9 6*3*15mm Magnet 1 PC #11 7*3.
Step 1. Attach magnet (part #6) to cross rail (part D) using round head screws (part #7) and phillips head screwdriver. Attach handle (part #10) to drawer front panel (part F) using short round head bolts (part #12) and phillips head screwdriver. #7 #7 #6 #7 D #6 #12 F #6 #7 #10 #12 #10 x1 x2 x1 x2 Step 2. Attach door hinges (part #8) to left door panel (part K) and right door panel (part L) using screws (part #9) and phillips head screwdriver.
Step 3. Attach drawer panels (parts G & H) to drawer front panel (part F) using long screws (part #16) and phillips head screwdriver. Slide drawer bottom panel (part J) into the grooves of assembled unit (parts F, G & H). Attach drawer back panel (part I) to assembled unit (parts G, H & J) using long screws (part #16) and phillips head screwdriver. #16 #16 J G F G H F #16 #16 H #16 #16 I #16 #16 G J H #16 x8 Step 4.
Step 5. Attach top panel (part A) to assembled unit (parts B & C ) using wood dowels (part #5), bolts (part #1), spring washers (part #2), flat washers (part #3) and allen wrench (part #4). x4 #3 #5 #2 #1 #4 #3 #5 #2 #1 #4 A C B #1 #2 #3 #4 #5 x4 x4 x4 x1 x4 Step 6. Attach bottom panel (part E) to assembled unit (parts B & C) using wood dowels (part #5), bolts (part #1), spring washers (part #2), flat washers (part #3) and allen wrench (part #4).
Step 7. Carefully turn unit upright. Attach back panel (part M) to assembled unit (parts A, B, C & E) using short screws (part #14) and phillips head screwdriver. x16 A M #14 B C M #14 E #14 x 16 Step 8. Place shelf holders (part #13) into desired position and slide adjustable shelf (part N) and assembled drawer into place. Move the sliders to the front end of rail before sliding the drawer into place.
Step 9. Attach door panels (parts K & L) to panels (parts B & C) using screws (part #9) and phillips head screwdriver. NOTE: It is important to adjust levelers once fully assembled and uprigft. Extend adjustable leveler until it's firmly in contact with the floor. If relocating, adjust leveler as needed until it's firmly in contact with the floor in new location. Important: Safety strap kit (part #15) must be installed to prevent tipping, damage and/or injury.
#15 Safety Strap Kit 1 SET A B D C Wall Anchor Bracket 8*3*15mm Short Screw 1 PC 2 PCS 1 PC E 8*4*35mm Long Screw 1 PC Safety Wall Strap 1 PC SAFETY WALL STRAP INSTALLATION Note: It is highly recommended to install this safety strap kit to prevent tipping, damage and/or injury. 1. Insert short screw (C) and safety wall strap (E) through bracket (B) and attach to top panel (part A) using phillips head screwdriver. 2. Drill a 11/32" hole where you want to secure the unit.
