Instructions / Assembly

ManualsBrandsCROSLEY FURNITURE ManualsFurnitureDarcy Dark Brown Sideboard

Table Of Contents

Summary of content (9 pages)

PAGE 1
PAGE 2
PART LIST Top Panel Left Panel Right Panel Bottom Panel | Adjustable Shelf 1PC 1PC 1PC 1PC 4 PCS Middle Panel Left Door Right Door Middle Leg Back Panel 1PC PCS PCS 1PC 1PC
PAGE 3
HARDWARE LIST Denseness Depression => $1/4" $8x30mm Long Bolt Short Bolt Spring Washer Flat Washer Wood Dowel 4 PCS (Extra 1) |8 PCS (Extra 1) PCS PCS 12 PCS (Extra $5/32x25mm $3x14mm Handle Round Head Double Magnet Round Head Shelf Holder Bolt Screw 4 PCS 8 PCS 2 PCS 4 PCS 16 PCS (Extra $3x14mm ©3.5x14 mm Screw Bend Hinge Long Screw Allen Wrench | Safety Strap Kit 26 PCS (Extra 1) 8 PCS 48 PCS (Extra 1) 1PC 18ET ADDITIONAL TOOLS (Not Provided) Note: It is not recommended to use power tools during assembly.
PAGE 4
Step 1. Attach handles (part #6) to doors (parts G & H) using round head bolts (part #7) and fillips head screwdriver. Attach bend hinges (part #12) to doors (parts G & H) using long screws {part #13) and fillips head screwdriver. Attach double magnets (part #8) to top panel (part A) using round head screws (part #9) and fillips head screwdriver. #128 xX 8 #13» X16 Step 2. Attach middle leg (part I) to bottom panel (part D) rotate to secure.
PAGE 5
Step 3. Attach panels (parts bottom panel (part D) using wood dowels (part #5), short bolts (part #2), spring washers (part #3), flat washers (part #4) and Allen wrench (part #14). Step 4. Carefully turn unit upright. Attach top panel (part A) to assembled unit (parts using wood dowels (part #5), long bolts (part #1), short bolts (part #2), spring washers (part #3), flat washers (part #4) and Allen wrench (part #14).
PAGE 6
Step 5. Attach back panel (part J) to assembled unit (parts using screws (part #11) and fillips head screwdriver. Step 6. Place shelf holders (part #10) into desired position and slide adjustable shelves (part E) into place.
PAGE 7
Step 7. Attach right doors (part H) to panels (parts C & F) using long screws (part #13) and fillips head screwdriver. #13 = X16 Step 8. Attach left doors (part G) to panels (parts B & F) using long screws (part #13) and fillips head screwdriver. Note: It is important to adjust levelers once fully assembled and upright. Extend adjustable leveler until it's firmly in contact with the floor. If relocating, adjust leveler as needed until it's firmly in contact with the floor in new location.
PAGE 8
5/8"x #3xD8 $4xD8 Safety Strap | Wall Anchor Bracket Short Screw | Long Screw | Safety Wall Kit Strap 18ET 1PC PCS 1PC 1PC 1PC SAFETY WALL STRAP INSTALLATION Note: It is highly recommended to install this safety strap kit to prevent tipping, damage and/or injury. 1. Insert short screw (C) and safety wall strap (E) through bracket (B) and attach to top panel (part A} using fillips head screwdriver. 2. Drill a 11/32" hole where you want to secure the unit.
PAGE 9
ADJUST YOUR DOORS TO MAKE THE GAPS MORE EVEN (OPTIONAL). STEP 1 Open the door TOP PANEL STEP 2 STEP 2a MOVE DOOR IN STEP 2b MOVE DOOR OUT Adjust the gap between door panel and side panel TOP PANEL SIDE PANEL Loosen the screw indicated a little, adjust the hinge to right position (see step 2a & 2b), then tighten the screw. ANY TOP PANEL SIDE PANEL DOOR too small gap TOP oe SIDE PANEL oc big gap TOP PANEL TOP PANEL Push the hinge back a little. Pull the hinge forward a little.