PART LIST Top Panel Bottom Panel Left Panel Right Panel Middle Partition Panel 1PC 1PC 1PC 1PC 1PC Left Door Right Door Left Cross Rail | Right Cross Rail | Front Top Rail Panel Panel 1PC 1PC 1PC 1PC 1PC Back Top Panel Back Bottom |Back Partition Rail| Back Panel Adjustable Shelf Rail 1PC 1PC PCS PCS PCS Drawer Front Drawer Left Drawer Right Drawer Back Drawer Bottom Panel Panel Panel Panel Panel PCS PCS PCS PCS PCS uU Towel Bar PCS
HARDWARE LIST #1 & 28*30mm #2 & @8*50mm #3 @ & Short Wood Lowell Long Wood Cam Lock Cam Bolt Barrel Nut Dowel 27 PCS (Extra 1) 1PC 18 PCS (Extra 1)| 18 PCS (Extra 1) 6 PCS | | Long Bolt Short Bolt Long Round Short Round Round Head Head Bolt Head Bolt Screw 6 PCS (Extra) | 4 PCS (Extra) | PCS (Extra) | 4 PCS (Extra 1) | 8 PCS (Extra _ Flat Head Short Flat Head Magnet Knob Handle Screw Screw 1PC 16 PCS (Extra 1) 4 PCS PCS PCS #16 #17 #18 Shelf Holder [Adjustable Leveler| Allen Wrench 8 PCS (Extra 1) 4 PCS 1PC
Step 1. Attach cam bolts (part #4) to panels (parts using fillips head screwdriver. NOTE: Do not over tighten cam bolts. Stop tightening once the threads on cam bolt are no longer visible. Step 2. Attach magnets (part #13) to middle partition panel (part E) using round head screws (part #10) and fillips head screwdriver. Attach knobs (part #14) to door panels (parts F & G) using long round head bolts (part #8) and fillips head screwdriver.
Step 3. Attach handle (part #15) to drawer front panel (part P) using short round head bolts (part #9) and fillips head screwdriver. Attach drawer panels (parts drawer front panel (part P) using short flat head screws (part #12) and fillips head screwdriver. Slide drawer bottom panel (part T) into grooves of assembled unit (parts Attach drawer back panel (part S) to assembled unit (parts using short flat head screws (part #12) and fillips head screwdriver. Repeat for remaining drawer. #150x 2 Step 4.
Step 5. Attach back top panel (part K) to left panel (part C) using short wood dowel (part #1) and cam locks (part #3). Attach back partition rails (part M) to back top panel (part K) using short wood dowels (part #1). Slide back panels (part N) into grooves of assembled unit (parts NOTE: Cam locks must rotate a full 180°. See pictured insert. ete ote Step 6. Attach back bottom rail (part L) to assembled unit (parts using short wood dowels (part #1) and cam lock (part #3).
Step 7. Attach right panel (part D) to assembled unit (parts using short wood dowels (part #1) and cam locks (part #3). NOTE: Cam locks must rotate a full 180°. See pictured insert. Step 8. Attach bottom panel (part B) to assembled unit (parts using short wood dowels (part #1), barrel nuts (part #5), long bolts (part #6) and Allen wrench (part #18). Attach adjustable levelers (part #17) to bottom panel (part B).
Step 9. Carefully turn unit upright. Attach towel bars (part U) to panels (parts C & D) using short bolts (part #7) and Allen wrench (part #18). #7 ~ x4 #185 x1 Step 10. Attach top panel (part A) to assembled unit (parts using short wood dowels (part #1) and cam locks (part #3). NOTE: Cam locks must rotate a full 180°. See pictured insert.
Step 11. Place shelf holders (part #16) into desired position and then slide adjustable shelves (part O) into place. #16 & x8 Step 12. Attach door panels (parts placing bottom pin hinge (per-installed in door) in the per-drilled hole of bottom panel (part B). Then depress the top spring-loaded pin hinge so it can be placed in the per-drilled hole of cross rails (parts NOTE: Be sure top and bottom pin hinges are fully extended to secure doors in place.